User Manual

ManualsBrandsDatacomm Electronics ManualsAccessories & SuppliesDataComm Electronics Wall Plate: Flat Panel TV Power Kit with Gang Box/Power Cable, White

Use the Recessed Pro-Power Kit with Duplex Receptacle and Straight Blade Inlet to install power and low voltage cables behind your flat panel TV,

amplifier or other audio and video devices to your equipment room or at the location of your head end equipment (see Figures 1 & 2).

DataComm Electronics, Inc.

6349 Peachtree Street

Norcross, GA 30071-1725

888.223.7977

770.662.8205

www.datacommelectronics.com

Instruction / Installation Sheet

DataComm Electronics 45-0024-WH Recessed Pro-Power Kit with Duplex Receptacle and Straight Blade Inlet

Parts Included:

1. Recessed Low Voltage Mid-Size Plate with Duplex Receptacle

2. Recessed Low Voltage Cable Plate with Straight Blade Inlet

3. Two (2) Electrical Outlet Boxes

Four (4) Screws per Outlet Box

4. 15 Amp/125 Volt Tamper Resistant Duplex Receptacle

5. Three (3) Wire Nuts

6. 6ft. 16/2 with Ground Cord Set with 360

Rotating Head

Tools Needed:

1. Drywall Saw

2. 6 Ft. Tape Measure

3. Pencil

4. Screwdriver

Figure 1 – Front View

Figure 2 – Back View

IMPORTANT INSTRUCTIONS:

 Use the local electrical code approved installation when installing this product.

 The electrical parts in this kit are designed to be used only as a kit and none of these electrical parts are designed to be used individually.

 This product is not designed to be part of your home or a commercial building’s electrical wiring system.

 This installation is only energized (electrically active) when the supplied 6 ft. cord is plugged into the recessed straight blade inlet located on the

recessed low voltage cable plate and the straight blade end of the 6 ft. cord is plugged into either your surge protector or wall receptacle.

If you are not familiar with home wiring systems, please call a qualified electrician to install this product.

IMPORTANT INSTRUCTIONS:

This product is designed for retrofit work only because the electrical outlet box cannot be attached to a stud.

Installation Instructions for Retrofit Only:

Select the location of your flat panel TV mounting bracket. Now select the location for both cable plates for the Recessed Pro- Power Kit with Duplex

Receptacle and Straight Blade Inlet.

Page 1 of 4 9/21/12

Summary of content (8 pages)

PAGE 1
Instruction / Installation Sheet DataComm Electronics 45-0024-WH Recessed Pro-Power Kit with Duplex Receptacle and Straight Blade Inlet DataComm Electronics, Inc. 6349 Peachtree Street Norcross, GA 30071-1725 888.223.7977 770.662.8205 www.datacommelectronics.com Parts Included: 1. Recessed Low Voltage Mid-Size Plate with Duplex Receptacle 2. Recessed Low Voltage Cable Plate with Straight Blade Inlet 3. Two (2) Electrical Outlet Boxes Four (4) Screws per Outlet Box 4.
PAGE 2
Installation / Instruction Sheet 45-0024-WH (Continued) 888.223.7977 www.datacommelectronics.com Installation Instructions for the Top Plate with Duplex Receptacle: Fig. 1 Figure 1 Top view - shows needed space between the drywall and the studs. Receptacle side of the Mid-Size Plate should be 3” from the stud but no more than 5” (review picture carefully). Fig. 2 Figure 2 Using the template supplied (see page 3 of instruction sheet), trace the opening needed.
PAGE 3
Installation / Instruction Sheet 45-0024-WH (Continued) 888.223.7977 www.datacommelectronics.com Installation Instructions for the Bottom Cable Plate with Straight Blade Inlet: Fig. 8 Figure 8 Wire the Cable Plate with Straight Blade Inlet to the 12/2 w/ground or 14/2 w/ground UL approved electrical building wire. Connect the hot line (black) wire to the black wire and the neutral (white) wire to the white wire on the straight blade inlet.
PAGE 4
Installation / Instruction Sheet 45-0024-WH (Continued) ONLY LICENSED PROFESSIONALS SHOULD INSTALL THIS PRODUCT 888.223.7977 www.datacommelectronics.com 6-1/2” TEMPLATE 4-1/2” Recessed Low Voltage Mid-Size Plate with Duplex Receptacle ACTUAL SIZE CUT ALONG DOTTED LINE  4-11/16” 4.
PAGE 5
Instruction / Installation Sheet DataComm Electronics 45-0028-WH Recessed Pro-Power Kit with Duplex Surge Suppressor DataComm Electronics, Inc. 6349 Peachtree Street Norcross, GA 30071-1725 888.223.7977 770.662.8205 www.datacommelectronics.com Parts Included: 1. Recessed Low Voltage Mid-Size Plate with Duplex Surge Receptacle 2. Recessed Low Voltage Cable Plate with Straight Blade Inlet 3. Two (2) Electrical Outlet Boxes Four (4) Screws per Outlet Box 4. 15 Amp/125 Volt Duplex Surge Receptacle 5.
PAGE 6
Installation / Instruction Sheet 45-0028-WH (Continued) 888.223.7977 www.datacommelectronics.com Installation Instructions for the Top Plate with Duplex Surge Receptacle: Figure 1 Top view - shows needed space between the drywall and the studs. Receptacle side of the Mid-Size Plate should be 3” from the stud but no more than 5” (review picture carefully). Fig. 1 Fig. 2 Fig. 3 Figure 2 Using the template supplied (see page 3 of instruction sheet), trace the opening needed.
PAGE 7
Installation / Instruction Sheet 45-0028-WH (Continued) 888.223.7977 www.datacommelectronics.com Installation Instructions for the Bottom Cable Plate with Straight Blade Inlet Fig. 8 Figure 8 Wire the Cable Plate with Straight Blade Inlet to the 14/2 w/ground UL approved electrical building wire. Connect the hot line (black) wire to the black wire and the neutral (white) wire to the white wire on the straight blade inlet.
PAGE 8
Installation / Instruction Sheet 45-0028-WH (Continued) ONLY LICENSED PROFESSIONALS SHOULD INSTALL THIS PRODUCT 888.223.7977 www.datacommelectronics.com 6-1/2” TEMPLATE 4-1/2” Recessed Low Voltage Mid-Size Plate with Duplex Surge Receptacle ACTUAL SIZE CUT ALONG DOTTED LINE  4-11/16” 4.