Specifications

i50 Manual (5.10)
Page 60
© 2015 Datalink Systems, Inc.
www.datalinksystemsinc.com
ID
Name
Description
Default
159
I_MAXCORNER
Max allowed cornering g-force (1/100 g). Set to zero to disable
60
160
I_USEBATT
Voltage (1/10 V) above which engine is running. Set to zero to disable. When
disabled, unit will use Engine On input or IGN to assume engine running. This
setting is used to count engine hours and calculate drive and idle times.
130
161
I_ACCELX
Accelerometer rotation around X axis (radians*10000). Set to zero to
recalibrate
0
162
I_ACCELY
Accelerometer rotation around Y axis (radians*10000). Set to zero to
recalibrate
0
163
I_MAXTILT
Max allowed tilt when stationary (degrees). Set to zero to disable
45
164
I_MOTIONSENSE
Set g-force required to trigger motion detection (approx 1/1000 g). Range 1-255
60
165
I_TRANSUDPPORT
UDP port for sending and receiving transparent data during a dial-up or Wi-Fi
connection. Set to zero to disable
4001
166
I_EMAILUDPPORT
UDP port for sending and receiving message/email data during a dial-up or Wi-
Fi connection. Set to zero to disable
4000
167
I_FUEL1
Engine Hours (1/100 gallons)
0
168
I_FUEL2
"
0
169
I_ADVANCED
Advanced GPS report. Bit 2=Digital I/O States. Bit 3=Cell Info. Bit 4=ADC2. Bit
5=ADC1. Bit 6=Battery Voltage. Bit 7=Temperature. Bit 8=Speed. Bit
9=Altitude. Bit 10=Heading. Bit 11=GPS HDOP
0
170
I_SIGNTRANS
Bit 1=Send NTCIP data in UDP format. Bit 0=Enable transparent access to sign
terminal
0
171
I_SIGNMSG
NTCIP Sign Message Number. Set to zero to use AMSIG protocol
0
172
I_SIGNID
NTCIP Sign ID
1
173
I_KENWOOD
Kenwood settings. Bit 7=Long data. Bit 6=NXDN. Bit 5=Software ACKs. Bit
4=WAN mode. Bit 3=Transparent. Bit 0=KW Prot Ver 1
193
174
I_RFBITS
RF COM settings. Bits 0-1=(Data bits-5). Bit 2=Extra Stop bits. Bit 3=Parity. Bit
4=Even
3
175
I_UNIT
Kenwood unit number used as destination when sending data (0000, 1000-
4999 for Fleetsync, or 00000-65519 for NXDN)
0
176
I_FLEET
Kenwood fleet/ID type for sending data (0, 100-349 for Fleetsync, or 0=GID,
1=UID, 2=Broadcast for NXDN)
0
177
I_ENGINEVE
Engine volumetric efficiency (%)
80
178
I_ENGINEDISP
Engine displacement (cc)
3000
179
I_LOWBATT
Low battery warning (1/10 V). Set to zero to disable
0
180
I_OUTPUT4
Output 4 Setting. See note at bottom for values
32
181
I_OUTPOLARITY4
Output 4 polarity (0=Low 1=High)
0
182
I_VOUT
VOUT function. See I/O note at bottom for values
40
183
I_VOUTPOLARITY
VOUT polarity (0=Low 1=High)
1
184
I_ADC1HIGH
Trigger event if ADC1 exceeds this voltage (1/10 V). Set to zero to disable
0
185
I_ADC1LOW
Trigger event if ADC1 drops under this voltage (1/10 V). Set to zero to disable
0
186
I_ADC2HIGH
Trigger event if ADC2 exceeds this voltage (1/10 V). Set to zero to disable
0
187
I_ADC2LOW
Trigger event if ADC2 drops under this voltage (1/10 V). Set to zero to disable
0
188
I_DEBOUNCEADC1
Debounce time (ms) for ADC1 changes
100
189
I_DEBOUNCEADC2
Debounce time (ms) for ADC2 changes
100
190
I_NOGPS
Send alert if GPS signal is unavailable for this period (sec). Ver 4.88 and later
only increment this counter while vehicle is moving.
0
191
I_RXUNIT
Kenwood unit number used to listen for data from base radio (1000-4999 for
Fleetsync, or 00001-65519 for NXDN). Set to zero to use I_UNIT
0
192
I_RXFLEET
Kenwood fleet ID used to listen for data from base radio (Fleetsync only). Set to
zero to use I_FLEET
0