- Datalogic Scanner Quick Guide

ManualsBrandsDatalogic Scanning ManualsScannerDS1100

DS1100 QUICK GUIDE

DS1100

General View: Laser Safety:

The scanner is classified as a Class 2 laser product according

to EN 60825-1 regulations and as a Class II laser product

according to CDRH regulations.

For installation, use and maintenance it is not necessary to

open the scanner.

There is a safety device which allows the laser to be switched

on only if the motor is rotating above the threshold for its correct

scanning speed.

The motor and the laser beam can be switched off through a

software command (see also the WinHost Help On Line).

LASER LIGHT

DO NOT STARE INTO BEAM

CLASS 2 LASER PRODUCT

MAX. OUTPUT RADIATION 1mW

EMITTED WAVE LENGTH 630-680 nm

TO EN 60825-1:2001

CAUTION-CLASS 3B LASER LIGHT WHEN

OPEN AVOID EXPOSURE TO BEAM

This product conforms to the

applicable requirements of

21CFR1040 at the date of

manufacture.

AVOID EXPOSURE

LASER LIGHT EMITTED

FROM THIS APERTURE

Figure A Warning and Device Class Label

Laser Beam Output Window

Laser Warning and

Device Class Label

Power On LED

Ext Trig LED

Laser On LED

Good Read LED

TX Data LED

Mounting Holes

The laser diode used in this device is classified as a class

3B laser product according to EN 60825-1 regulations

and as a Class IIIb laser product according to CDRH

regulations. As it is not possible to apply a classification

label on the laser diode used in this device, the following

label is reproduced below.

For further details on product installation,

see the complete Installation Manual.

DS1100 can be configured through the

WinHost Windows-based software program

available on the installation CD-ROM.

For configuration it is necessary to create a

cable connecting the scanner to the PC as

indicated in the “How To Build A Simple

Interface Test Cable” section of this guide.

Power Supply:

- This product is intended to be installed by

Qualified Personnel only.

- This accessory device is intended to be

supplied by a UL Listed or CSA Certified

Power Unit with «Class 2» or LPS power

source which supplies power directly to the

scanner via the 25-pin connector.

LASER LIGHT

AVOID EXPOSURE TO BEAM

CLASS 3B LASER PRODUCT

MAX. OUTPUT RADIATION 7 mW

EMITTED WAVE LENGTH 630~680 nm

TO EN 60825-1 (2001)

Laser Diode Class Label

Any violation of the optic parts in particular can cause

radiation up to the maximum level of the laser diode

(7 mW at 630 to 680 nm).

WEEE Compliance:

3 4 5

Summary of content (8 pages)

PAGE 1
DS1100 QUICK GUIDE DS1100 General View: Laser Safety: The scanner is classified as a Class 2 laser product according to EN 60825-1 regulations and as a Class II laser product according to CDRH regulations. For installation, use and maintenance it is not necessary to open the scanner. 1 There is a safety device which allows the laser to be switched on only if the motor is rotating above the threshold for its correct scanning speed.
PAGE 2
DS1100 QUICK GUIDE Model Description: DS1100 - X X X X Optical Resolution 1 = Standard resolution 2 = High resolution Communication Interface 1 = RS232 + RS485 Optic Version 0 = Linear 1 = Raster Reading Window Position 0 = Direct 1 = 90° Reading Performance: Version 1XXX 2XXX Reading Distance 30 mm (1.2 in) - 220 mm (8.7 in) on 0.50 mm (20 mils) codes 10 mm (0.4 in) - 110 mm (4.3 in) on 0.30 mm (12 mils) codes Max Code Resolution Speed mm (mils) scans/s 0.20 (8) 0.
PAGE 3
DS1100 QUICK GUIDE Electrical Connections: DS1100 is equipped with a cable terminated by a 25-pin female D-sub connector for connection with the power supply and input/output signals. Do not connect GND and SGND to different (external) ground references. GND and SGND are internally connected through filtering circuitry which can be permanently damaged if subjected to voltage drops over 0.8 Vdc.
PAGE 4
DS1100 QUICK GUIDE Reading Position: In DS1100-XXX1 models the laser beam is emitted from the output window with a 12° (± 2) skew angle. DS1100-XXX1 90° Reading Window Position 12° ± 2 Laser Beam Laser Beam DS1100-XXX0 Direct Reading Window Position ± 2° Input/Output Connections: Input DS1100 +5V Input EXTERNAL TRIGGER 13/9 VS 5 Vdc 19 EXT TRIG - User Interface +5V V 47 K 12/22 DS1100 47 K Signal GND Ground 18 IN1 - 12/22 GND NPN Ext.
PAGE 5
DS1100 QUICK GUIDE Connectivity: RS232 Point-to-point layout c RS232 Auxiliary Serial Interface d External Trigger (for On-Line mode) RS485 Master/Slave layout c RS232 Auxiliary Serial Interface d RS485 HD Main Serial Interface e External Trigger Multiplexer layout c RS485 HD Main Interface d RS232 Auxiliary Interface (Local Echo) e External Trigger (for On-Line mode) 5
PAGE 6
DS1100 QUICK GUIDE Reading Diagrams: DS1100-1XXX (Standard Resolution) 0 0 5 4 3 1 20 2 40 3 60 4 5 6 7 8 9 (in) 10 80 100 120 140 160 180 200 220 240 260 (mm) 120 100 80 60 2 CONDITIONS Code = Interleaved 2/5 or Code 39 PCS = 0.90 Pitch angle = 0° Skew angle = 15° Tilt angle = 0° 40 1 20 0 0 1 20 2 0.20 mm (8 mils) 0.30 mm (12 mils) ≥ 0.
PAGE 7
DS1100 QUICK GUIDE User Interface: The following table contains the pinout for standard RS232 PC Host interface. For other user interface types please refer to their own manual.
PAGE 8
DATALOGIC S.p.A.