Magellan 1000i TM On-Counter Presentation Omnidirectional Bar Code Reader Product Reference Guide
Datalogic Scanning, Inc. 959 Terry Street Eugene, Oregon 97402 Telephone: (541) 683-5700 Fax: (541) 345-7140 An Unpublished Work - All rights reserved. No part of the contents of this documentation or the procedures described therein may be reproduced or transmitted in any form or by any means without prior written permission of Datalogic Scanning, Inc. or its subsidiaries or affiliates ("Datalogic" or “Datalogic Scanning”).
Table of Contents About This Manual ............................................................................................................... 1-1 Manual Conventions ....................................................................................................... 1-1 Connecting the Scanner ....................................................................................................... 1-2 Programming ..........................................................................................
Wand Idle State ........................................................................................ Signal Speed ............................................................................................ Transmit Trailing Noise .............................................................................. Transmit Leading Noise ............................................................................. Symbology Conversion ............................................................................
Start/Stop Characters ...................................................................................................5-27 Code 39 Full ASCII .......................................................................................................5-28 Length Control .............................................................................................................5-29 Code 39 Length 1, Length 2 Programming Instructions ......................................................5-30 Quiet Zones .......
Minimum Reads ........................................................................................................... 5-67 2D Symbologies .................................................................................................................. 6-2 PDF 417 .......................................................................................................................6-2 Disable/Enable PDF 417 ...............................................................................
Chapter 1 Getting Started The Magellan® 1000i Omni-Directional Imaging Scanner offers hands-free scanning for small, easily handled items and handheld scanning for bulkier items. Its aggressive imaging performance and intuitive operation reduces user training and speeds checkout for better customer service. About This Manual This manual presents advanced user information which includes connection, programming, product and cable specifications, and other useful references.
Getting Started Connecting the Scanner The scanner kit you ordered to match your interface should provide a compatible cable for your installation. Use the appropriate instructions below to connect the scanner to the terminal, PC or other host device. Upon completing the connection via the appropriate interface instructions below, proceed to the Interface Related Features section of this manual and scan the barcode to select the correct interface type.
Programming Wand Emulation Connection — Connect the scanner to the appropriated port on the terminal/PC using the correct cable for the interface type you ordered. Reference Figure 2. IBM Connection — Connect the scanner to the IBM port on the terminal/PC using the correct IBM cable. Reference Figure 2. Keyboard Wedge Connection — Before connection, turn off power to the terminal/PC. The Keyboard Wedge cable has a ‘Y’ connection from the scanner.
Getting Started LED and Beeper Indicators The scanner’s beeper sounds and its green LED illuminates to indicate various functions or errors on the scanner. The tables below list these indications. One exception to the behaviors listed in the tables is that the scanner’s functions are programmable, and may or may not be turned on. For example, certain indications, such as the power-up beep can be disabled using programming barcode labels.
Error Codes Error Codes Upon startup, if the scanner flashes its indicator LED or sounds an unexpected series of beep tones (other than normal power-up indications), this means the scanner has not passed its automatic Selftest and has entered FRU1 isolation mode. If the scanner is reset or the trigger is pulled, the sequence will be repeated. The following table describes the LED flashes/beep codes associated with an error found.
Getting Started NOTES 1-6 Magellan® 1000i
Chapter 2 General Features Double Read Timeout The Double Read Timeout feature sets a time limit that determines how much time must pass before reading the same label again (e.g. two identical items in succession). START / END PROGRAMMING BARCODES 0.1 Second 0.2 Second 0.3 Second 0.4 Second DEFAULT 0.5 Second 0.
General Features Double Read Timeout — cont. START / END PROGRAMMING BARCODES 0.7 Second 0.8 Second 0.
Label Gone Timeout Label Gone Timeout This feature sets the time after the last label segment is seen before the scanner prepares for a new label. START / END PROGRAMMING BARCODES Sets the label gone timeout duration using hex values from 000 to 255 in increments of ten milliseconds (10ms or 0.01 seconds).
General Features Sleep Mode This feature specifies the amount of time with no barcode reads before the scanner enters sleep mode.
Sleep Mode Sleep Mode — cont.
General Features LED and Beeper Indicators Power On Alert Disables or enables the indication (a single beep) that the scanner has finished all its power up tests and is now ready for operation.
LED and Beeper Indicators Good Read: When to Indicate This feature specifies when the scanner will provide indication (beep and/or flash its green LED) upon successfully reading a barcode. Choices are: • Good Read = Indicate after decode • Good Read = Indicate after transmit • Good Read = Indicate after CTS goes inactive, then active This option (Indicate after CTS goes inactive, then active), which uses CTS, is only valid for RS-232 interfaces.
General Features Good Read Beep Control This feature enables/disables the scanner’s ability to beep upon a successful decode of a barcode. START / END PROGRAMMING BARCODES Disable Enable DEFAULT Good Read Beep Frequency Adjusts the good read beep to sound at a selectable low, medium or high frequency, selectable from the list below. (Controls the beeper’s pitch/tone.
LED and Beeper Indicators Good Read Beep Length Specifies the duration of a good read beep.
General Features Good Read Beep Volume Selects the beeper volume (loudness) upon a good read beep. There are three selectable volume levels.
Scanning Features Scanning Features Targeted Scanning Mode Upon pressing the button, the scanner will project an aiming pattern to assist in centering over the barcode. Scanning then takes place as soon as the button is released. When add-ons are enabled and a barcode is being read while in Targeted Mode, position the pointer at or near the end of the base label to ensure the scanner will read both the base and add-on label. NOTE Targeted Scanning Mode will read barcodes in any orientation.
General Features Target Mode Linger Time Specifies the time duration the scanner remains in the targeted mode of operation after reading a barcode before reverting to Omni-directional Mode.
Scanning Features Wake Up Intensity This feature indicates the percentage of ambient light change which will trigger the scanner to wake up from Sleep Mode. Lower settings provide greater sensitivity. The seelectable range for this setting is 5% to 15%.
General Features Wake Up Intensity — cont.
Chapter 3 Interface Related Features At the time of this writing, the Scanner supports the interfaces listed in Table 3-1. Select the desired interface type from the table, then reference the page number given for the customizable features section associated with each interface. See Table 3-2 for a description of each Keyboard Wedge interface type (A through Y as listed). Table 3-1.
Interface Related Features Table 3-2.
Interface Selection Interface Selection START / END PROGRAMMING BARCODES RS-232 Standard RS-232 Wincor-Nixdorf IBM 4683 Port 5B IBM 4683 Port 9B IBM 4683 Port 17 USB-OEM USB Keyboard Wand Emulation USB COM Product Reference Guide 3-3
Interface Related Features Interface Selection — cont.
Interface Selection Interface Selection — cont.
Interface Related Features Interface Selection — cont.
Interface Features Interface Features Obey/Ignore Host Commands When set to ignore host commands, the scanner will ignore all host commands except for the minimum set necessary to keep the interface active and transmit labels For normal operation of the interface, select Obey Host Commands.
Interface Related Features Interface Features — cont. Host Transmission Buffers Specifies the number of host transmission(s) that may be buffered. By buffering data from a barcode, the scanner can continue to read a new barcode while the old one is being transmitted to the host. Selecting BUFFERS = 1 means that the first barcode must be transmitted before a new one can be read. A selection of BUFFERS = 2 means that a new barcode can be read while data from the first barcode is transmitted.
Interface Features RS-232 Interface Features START / END PROGRAMMING BARCODES 1200 Baud 2400 Baud 4800 Baud 9600 Baud DEFAULT 19200 Baud ³ 38400 Baud 57600 Baud 115200 Baud Product Reference Guide 3-9
Interface Related Features RS-232 Interface Features — cont.
Interface Features RS-232 Interface Features — cont. Hardware Flow Control Disable Hardware Control— The scanner transmits to the host regardless of any activity on the CTS line. Enable CTS Flow Control— The CTS signal controls transmission of data to the host. Enable CTS Scan Control— The CTS line must be active for the scanner to read and trans- mit data.
Interface Related Features RS-232 Interface Features — cont. Intercharacter Delay This delay is inserted after each data character transmitted. If the transmission speed is too high, the system may not be able to receive all characters. You may need to adjust the delay to make the system work properly.
Interface Features Intercharacter Delay — cont. START / END PROGRAMMING BARCODES Interchar Delay = 80 msec Interchar Delay = 90 msec Software Flow Control Disables/Enables software control using XON/XOFF characters.
Interface Related Features RS-232 Interface Features — cont. Host Echo When enabled, this feature passes all data through the scanner to the host as it comes in. This feature is used for applications where “daisy chaining” of RS-232 devices onto the same cable is necessary.
Interface Features RS-232 Interface Features — cont. Host Echo Quiet Interval This setting specifies the time interval of RS-232 channel inactivity which must transpire before the scanner will break the host echo loop to transmit the barcode data that has just been scanned to the host.
Interface Related Features Host Echo Quiet Interval — cont. START / END PROGRAMMING BARCODES Host Echo Quiet Interval = 80msec Host Echo Quiet Interval = 90msec Host Echo Quiet Interval = 100msec Signal Voltage: Normal/TTL Specifies whether the RS-232 interface provides TTL levels on the output pins TxD and RTS.
Interface Features RS-232 Invert Enables/disables inversion of RS-232 TXD and RXD signals. START / END PROGRAMMING BARCODES Disable RS-232 Invert DEFAULT Enable RS-232 Invert Beep on ASCII BEL Enables/disables ability of scanner to beep (sound a good read tone) on receiving an ASCII BEL (07 hex).
Interface Related Features Beep on Not on File Select for the host to beep (or not) when a not-on-file (host command) condition is detected by the host.
Interface Features ACK NAK Options This enables/disables the ability of the scanner to support the RS-232 ACK/NAK protocol. When configured, the scanner and/or host sends an “ACK” when it receives data properly, and sends “NAK” when the data is in error.
Interface Related Features RS-232 Interface Features — cont. — cont. ACK Character START / END PROGRAMMING BARCODES Sets the ACK character from the set of ASCII characters or any decimal value from 000 to 255. Pad entries of less than three digits with zeros, as in “005”.
Interface Features RS-232 Interface Features — cont. Retry on ACK NAK Timeout Enables/disables retry after the configurable ACK NAK Timeout Value (set in the following feature) has expired. START / END PROGRAMMING BARCODES Disable Retry on ACK NAK Timeout Enable Retry on ACK NAK Timeout DEFAULT ACK NAK Timeout Value START / END PROGRAMMING BARCODES This item specifies the time the scanner will wait for an ACK character from the host following a label transmission.
Interface Related Features RS-232 Interface Features — cont. ACK NAK Retry Count START / END PROGRAMMING BARCODES This feature sets the number of times for the scanner to retry a label transmission under a retry condition.
Interface Features RS-232 Interface Features — cont. ACK NAK Error Handling This item specifies the method the scanner will use to handle errors detected while waiting to receive the ACK character from the host. Errors include unrecognized host commands and communication errors such as parity or framing errors.
Interface Related Features RS-232 Interface Features — cont. Transmission Failure Indication Enables/disables bad-label indication upon transmission failure. START / END PROGRAMMING BARCODES Disable Transmission Error Indication Enable Transmission Error Indication DEFAULT USB-OEM Interface Features USB-OEM Device usage The USB-OEM protocol allows for the scanner to be identified as one of two different types of barcode scanners.
Interface Features IBM IBM Transmit Labels in Code 39 Format This feature enables/disables scanner's ability to set a symbology identifier for a specified label to Code 39 before transmitting that label data to an IBM host. This applies to: Code 128, Codabar and Code 93 for USB-OEM; Code 128, Codabar and Code 93 for IBM Port 5B; and Codabar and Code 93 for IBM Port 9B.
Interface Related Features Wand Emulation Supported Symbologies The Wand Emulation interface will transmit barcode data as a wand device would. This interface will transmit the following barcode symbologies: • UPC/EAN • UPC/EAN with addons • Code 39 • Full ASCII Code 39 • Interleaved 2 of 5 • Codabar • Code 128 Pharmacode 39 is transmitted as Code 39. All other barcode symbology types read by the scanner will be transmitted as Code 128.
Interface Features Wand Emulation — cont. Bar/Space Polarity Low/High — Black will be transmitted as a low voltage level (0 to +0.7V) and space as high level (+2.4 to +5.25V). High/Low — Black will be transmitted as a high voltage level (+2.4 to +5.25V) and space as low level (0 to +0.7V). START / END PROGRAMMING BARCODES Bar/Space = Low/High Bar/Space = High/Low DEFAULT Wand Idle State This feature specifies the level of the wand output signal when idle. TTL logic levels: High voltage level (+2.
Interface Related Features Wand Emulation — cont. Signal Speed The speed of the transmission can be set. This selects the width of the minimum narrow bar. 330 microseconds 660 microseconds START / END PROGRAMMING BARCODES Signal Speed = 330mS Signal Speed = 660mS DEFAULT Transmit Trailing Noise The transmission of noise pulses after the label may be enabled or disabled.
Interface Features Wand Emulation — cont. Transmit Leading Noise The transmission of noise pulses before the barcode may be enabled or disabled. START / END PROGRAMMING BARCODES Disable Leading Noise Enable Leading Noise DEFAULT Symbology Conversion Wand Emulation can convert all barcodes to a single symbology.
Interface Related Features Keyboard Wedge and USB Keyboard As a keyboard interface, the scanner supports most popular PCs and IBM terminals. The installation of the wedge is a fairly simple process that doesn’t require any changes of software or hardware. All of the options in this section apply to the Keyboard Wedge, however, only some apply to USB Keyboard. NOTE Keyboard Layout The Keyboard Layout option supports many countries.
Interface Features Keyboard Wedge — cont.
Interface Related Features Keyboard Wedge — cont. START / END PROGRAMMING BARCODES Slovakia ³ Romania Croatia Poland Caps Lock State Specifies the format in which the scanner sends character data.
Interface Features Keyboard Wedge — cont. Power-On Simulation This feature does not apply to the USB Keyboard interface. NOTE All PCs check the keyboard status during the power-on Selftest. It is recommended that you enable this function if you are working without a keyboard installation. It simulates keyboard timing and passes the keyboard status to the PC during power-on.
Interface Related Features Control Characters Specifies how the scanner transmits ASCII control characters to the host. Choices are: • Disable Control Characters • Enable transmission of control characters to host • Send characters between 00H and 1FH according to a special function-key mapping table. (This is used to send keys that are not in the normal ASCII set; a unique set is provided for each available scancode set. Reference Appendix E, Keyboard Function Key Mappings.
Interface Features Keyboard Wedge — cont. Wedge Quiet Interval This feature does not apply to the USB Keyboard interface. NOTE Quiet Interval is the amount of time to look for keyboard activity before the scanner breaks the keyboard connection in order to transmit data to the host. START / END PROGRAMMING BARCODES Selectable from 000 (no interval) to 255 in 10 msec increments.
Interface Related Features Keyboard Wedge — cont. Intercharacter Delay This feature does not apply to the USB Keyboard interface. NOTE START / END PROGRAMMING BARCODES One-half of the delay specified below is inserted between scancodes within each character. If the transmission speed is too high, the system may not be able to receive all characters. You may need to adjust the delay to make the system work properly. Selectable from 000 to 255 in 10msec increments.
Chapter 4 Data Editing Data Editing Overview It is not recommended to use these features with IBM or Wand Emulation interfaces. CAUTION When a barcode is scanned, additional information can be sent to the host computer along with the barcode data. This combination of barcode data and supplementary user-defined data is called a “message string.” The features in this chapter can be used to build specific user-defined data into a message string.
Data Editing Global Prefix/Suffix Up to 20 ASCII characters may be added as a prefix (in a position before the barcode data) and/ or as a suffix (in a position following the barcode data) as indicated in Figure 4-2. Figure 4-2. Prefix and Suffix Positions OR... Prefix Label ID AIM ID Bar Code Data Label ID Suffix 00 - 20 Characters (ASCII) AND OR Example: Setting a Prefix In this example, we’ll set a prefix for all symbologies. 1.
Global Prefix/Suffix Global Prefix/Suffix — cont. START / END PROGRAMMING BARCODES Sets up to 20 characters each from the set of ASCII characters or any hex value from 0 to FF. To configure this feature, scan the “START/END” barcode above to place the unit in Programming Mode, then the “Set Prefix” or “Set Suffix,” followed by the digits from the Alphanumeric table in Appendix C, Alpha-Numeric Pad representing your desired character(s).
Data Editing AIM ID AIM (Automatic Identification Manufacturers) label identifiers are assigned from a globally standardized list — as opposed to custom label ID characters you select yourself — and can be included with scanned barcode data. AIM label identifiers consist of three characters as follows: • A close brace character (ASCII ‘]’), followed by... • A code character (see the table below), followed by...
Label ID Label ID A Label ID is a customizable code of up to two ASCII characters (00-FF), used to identify a barcode (symbology) type. See Appendix D, Default Settings, for a listing for common symbologies. It can be appended previous to or following the transmitted barcode data depending upon how this option is enabled. This feature provides options for configuring custom Label IDs individually per symbology.
Data Editing Label ID — cont.
Label ID Label ID — cont.
Data Editing Label ID — cont.
Label ID Label ID — cont.
Data Editing 4-10 Magellan® 1000i
Label ID Label ID — cont.
Data Editing Case Conversion This feature can convert scanned barcode data to either all lower case (a through z) or all upper case (A through Z) characters. Case conversion affects ONLY scanned barcode data, and does not affect Label ID, Prefix, Suffix, or other appended data.
Character Conversion Character Conversion Character conversion is an eight byte configuration item. The eight bytes are 4 character pairs represented in hexadecimal ASCII values. The first character in the pair is the character that will be converted. The second character in the pair is the character to convert to. If the character to convert in a pair is FF, then no conversion is done.
Data Editing 4-14 Magellan® 1000i
Chapter 5 Symbologies The scanner supports the following symbologies (barcode types). Options for each symbology are included in this chapter.
Symbologies UPC-A — continued Check Digit Transmission Enable this option to transmit the check digit along with UPC-A barcode data. START / END PROGRAMMING BARCODES Don’t Send Check Digit ³ Send Check Digit DEFAULT Expand UPC-A to EAN-13 Expands UPC-A data to the EAN-13 data format. Selecting this feature also changes the symbology ID to match those required for EAN-13.
UPC-A UPC-A — continued Number System Transmission This feature enables/disables transmission of UPC-A System Number. START / END PROGRAMMING BARCODES Disable Number System Transmission Enable Number System Transmission DEFAULT UPC-A Minimum Reads This feature specifies the minimum number of consecutive times a UPC-A label must be decoded before it is accepted as good read.
Symbologies UPC-A — continued UPC-A In-store Minimum Reads This feature specifies the minimum number of consecutive times an in-store printed label must be decoded before it is accepted as good read.
UPC-E UPC-E The following options apply to the UPC-E symbology. Disable/Enable UPC-E When disabled, the scanner will not read UPC-E barcodes. START / END PROGRAMMING BARCODES Disable UPC-E Enable UPC-E DEFAULT Check Digit Transmission Enable this option to transmit the check digit along with UPC-E barcode data.
Symbologies UPC-E — continued Number System Digit The Number System Digit (NSD) which is always a zero (0) in the leading position can be optionally included (or not) with scanned barcode data. START / END PROGRAMMING BARCODES Exclude Number System Digit DEFAULT Include Number System Digit ³ 0 2 8 0 1 Expand to UPC-E to UPC-A Enables/disables expansion of UPC-E labels to UPC-A. Selecting this feature also changes the symbology ID to match those required for UPC-A.
UPC-E UPC-E — continued Expand UPC-E to EAN13 Enables/disables expansion of UPC-E labels to EAN-13. Selecting this feature also changes the symbology ID to match those required for EAN-13. START / END PROGRAMMING BARCODES Don’t Expand UPC-E to EAN-13 DEFAULT Expand UPC-E to EAN-13 Minimum Reads This feature specifies the minimum number of consecutive times a UPC-E label must be decoded before it is accepted as good read.
Symbologies GTIN The following options apply to the GTIN label data format. Expand UPC/EAN to GTIN When this feature is enabled, the scanner will translate UPC/EAN labels to the 14 digit GTIN format.
EAN-13 EAN-13 The following options apply to the EAN-13 symbology. Disable/Enable EAN-13 When disabled, the scanner will not read EAN-13 barcodes. START / END PROGRAMMING BARCODES Disable EAN-13 Enable EAN-13 DEFAULT Check Digit Transmission Enable this option to transmit the check digit along with EAN-13 barcode data.
Symbologies EAN-13 — continued EAN-13 Flag 1 Character Enables/disables transmission of an EAN/JAN13 Flag1 character. START / END PROGRAMMING BARCODES Don’t Transmit EAN-13 Flag 1 Char Transmit EAN-13 Flag 1 Char DEFAULT ISBN When enabled, this feature truncates the leading three digits from labels that contain ISBN (International Standard Book Number) and appends an ISBN check character to the end of the label. These codes are used for books and magazines. Labels with ISBN codes start with "978".
EAN-13 EAN-13 — continued Minimum Reads This feature specifies the minimum number of consecutive times an EAN-13 label must be decoded before it is accepted as good read.
Symbologies EAN-8 The following options apply to the EAN-8 symbology. Disable/Enable EAN-8 When disabled, the scanner will not read EAN-8 barcodes. START / END PROGRAMMING BARCODES Disable EAN-8 Enable EAN-8 DEFAULT Check Digit Transmission Enable this option to transmit the check Digit along with EAN-8 barcode data.
EAN-8 EAN-8 — continued Expand EAN-8 to EAN-13— Expands EAN-8 data to the EAN-13 data format. Selecting this feature also changes the symbology ID to match those required for EAN-13. START / END PROGRAMMING BARCODES Don’t Expand to EAN-13 DEFAULT Expand to EAN-13 Minimum Reads This feature specifies the minimum number of consecutive times an EAN-8 label must be decoded before it is accepted as good read.
Symbologies Enable EAN Two-Label Enables/disables the ability of the scanner to decode EAN two-label pairs.
Add-ons Add-ons Add-ons (or supplemental characters) are commonly added to the end of UPC/EAN barcodes. The scanner will read the add-ons if they are enabled and in the field of view. Three add-on types are supported: 2-digit, 5-digit and Code 128 add-ons. Supported options are: None— This option directs the scanner to ignore add-on portion of a UPC/EAN barcode but still read the main portion of the barcode. 2 Digits— The scanner will optionally read 2-digit add-ons with the UPC/EAN label.
Symbologies Add-ons — continued START / END PROGRAMMING BARCODES Disable Optional 2-Digit Add-ons DEFAULT Enable Optional 2-Digit Add-ons Disable Optional 5-Digit Add-ons DEFAULT Enable Optional 5-Digit Add-ons ³ 0 1 1 0 1 Disable Optional Code 128 Add-ons DEFAULT Enable Optional Code 128 Add-ons 5-16 Magellan® 1000i
GS1 DataBar Omnidirectional / Stacked Omnidirectional GS1 DataBar Omnidirectional / Stacked Omnidirectional The following options apply to the GS1 DataBar Omnidirectional symbology. Disable/Enable GS1 DataBar Omnidirectional When this feature is disabled, the scanner will not read GS1 DataBar Omnidirectional barcodes.
Symbologies GS1 DataBar Omnidirectional / Stacked Omnidirectional — continued Minimum Reads This feature specifies the minimum number of consecutive times an GS1 DataBar Omnidirectional label must be decoded before it is accepted as good read.
GS1 DataBar Expanded / Expanded Stacked GS1 DataBar Expanded / Expanded Stacked The following options apply to the GS1 DataBar Expanded symbology. Disable/Enable GS1 DataBar Expanded When this feature is disabled, the scanner will not read GS1 DataBar Expanded barcodes. START / END PROGRAMMING BARCODES Disable GS1 DataBar Expanded DEFAULT Enable GS1 DataBar Expanded GS1-128 Emulation When enabled, GS1 DataBar Expanded barcodes will be translated to the GS1-128 label data format.
Symbologies GS1 DataBar Expanded / Expanded Stacked — continued Length Control Fixed Length Decoding— When fixed length decoding is enabled, the scanner will decode a barcode if the label length matches one of the configurable fixed lengths. Variable Length Decoding— When variable length decoding is enabled, the scanner will decode a barcode if the label length falls in the range of the configurable minimum and maximum length. Configuring Fixed Length Decoding: 1. Scan the START/END barcode. 2.
GS1 DataBar Expanded / Expanded Stacked GS1 DataBar Expanded / Expanded Stacked — continued GS1 DataBar Expanded Length 1, Length 2 Programming Instructions 1. Scan the START/END barcode. 2. Scan either the Set Length 1 or Set Length 2 barcode. 3. Turn to Appendix C, Alpha-Numeric Pad and scan the three digits (zero padded) representing the length in decimal notation. For GS1 DataBar Expanded barcodes, only the data characters are included in the length calculations. NOTE 4. Scan the START/END barcode.
Symbologies GS1 DataBar Expanded / Expanded Stacked — continued Minimum Reads This feature specifies the minimum number of consecutive times an GS1 DataBar Expanded label must be decoded before it is accepted as good read.
GS1 DataBar Expanded / Expanded Stacked GS1 DataBar Expanded / Expanded Stacked — continued Coupon Read Control This feature controls coupon reading.
Symbologies GS1 DataBar Limited The following options apply to the GS1 DataBar Limited symbology. Disable/Enable GS1 DataBar Limited When this feature is disabled, the scanner will not read GS1 DataBar Limited barcodes. START / END PROGRAMMING BARCODES Disable GS1 DataBar Limited DEFAULT Enable GS1 DataBar Limited GS1-128 Emulation When enabled, GS1 DataBar Limited barcodes will be translated to the GS1-128 label data format.
GS1 DataBar Limited GS1 DataBar Limited — continued Minimum Reads This feature specifies the minimum number of consecutive times an GS1 DataBar Limited label must be decoded before it is accepted as good read.
Symbologies Code 39 The following options apply to the Code 39 symbology. Disable/Enable Code 39 When this feature is disabled, the scanner will not read Code 39 barcodes. START / END PROGRAMMING BARCODES Disable Code 39 Enable Code 39 DEFAULT Check Character Calculation When enabled, the scanner will calculate the check character of the labels. Turn this option on only when a checksum is present in the Code 39 labels.
Code 39 Check Character Transmit Enable this option to transmit the check character with scanned barcode data. START / END PROGRAMMING BARCODES Disable Check Char Transmission Enable Check Char Transmission DEFAULT Start/Stop Characters Enables/disables transmission of Code39 start and stop characters.
Symbologies Code 39 Full ASCII Enables/disables the translation of Code 39 characters to Code 39 full-ASCII characters.
Code 39 Code 39 — continued Length Control Fixed Length Decoding— When fixed length decoding is enabled, the scanner will decode a barcode if the label length matches one of the configurable fixed lengths. Variable Length Decoding— When variable length decoding is enabled, the scanner will decode a barcode if the label length falls in the range of the configurable minimum and maximum length. Configuring Fixed Length Decoding: 1. Scan the START/END barcode. 2. Scan the Fixed Length Decoding barcode. 3.
Symbologies Code 39 Length 1, Length 2 Programming Instructions 1. Scan the START/END barcode. 2. Scan either the Set Length 1 or Set Length 2 barcode. 3. Turn to Appendix C, Alpha-Numeric Pad and scan the three digits (zero padded) representing the length in decimal notation. For Code 39 barcodes, all check, data and full ASCII shift characters are included in the length calculations. Start/Stop characters are not included. NOTE 4. Scan the START/END barcode.
Code 39 Code 39 — continued Code 39 Stitching Enables/disables stitching for Code 39 labels. When parts of a Code 39 barcode are presented to the scanner with this feature enabled, the barcode parts will be assembled by the scanner’s software, and the data will be decoded if all barcode proofing requirements are met.
Symbologies Pharmacode 39 The following options apply to the Pharmacode 39 symbology. Disable/Enable Pharmacode 39 When this feature is disabled, the scanner will not read Pharmacode 39 barcodes. START / END PROGRAMMING BARCODES Disable Pharmacode 39 DEFAULT Enable Pharmacode 39 Start/Stop Characters Enables or disables transmission of Pharmacode 39 start/stop characters.
Pharmacode 39 Check Character Transmit Enable this option to transmit the check character with scanned barcode data.
Symbologies Code 128 The following options apply to the Code 128 symbology. Disable/Enable Code 128 When this feature is disabled, the scanner will not read Code 128 barcodes. START / END PROGRAMMING BARCODES Disable Code 128 Enable Code 128 DEFAULT Disable/Enable EAN 128 When this feature is disabled, the scanner will not read EAN 128 barcodes.
Code 128 Code 128 — continued Transmit Function Characters Enables/disables transmission of Code128 function characters 1, 2, 3, and 4.
Symbologies Code 128 — continued Length Control Fixed Length Decoding— When fixed length decoding is enabled, the scanner will decode a barcode if the label length matches one of the configurable fixed lengths. Variable Length Decoding— When variable length decoding is enabled, the scanner will decode a barcode if the label length falls in the range of the configurable minimum and maximum length. Configuring Fixed Length Decoding: 1. Scan the START barcode. 2. Scan the Fixed Length Decoding barcode. 3.
Code 128 Code 128 — continued Code 128 Length 1, Length 2 Programming Instructions 1. Scan the START barcode. 2. Scan either the Set Length 1 or Set Length 2 barcode. 3. Turn to Appendix C, Alpha-Numeric Pad and scan the three digits (zero padded) representing the length in decimal notation. For Code 128 barcodes, only the data characters are included in the length calculations. NOTE 4. Scan the END barcode.
Symbologies Code 128 — continued Code 128 Stitching Enables/disables stitching for Code 128 labels. When parts of a Code 128 barcode are presented to the scanner with this feature enabled, the barcode parts will be assembled by the scanner’s software, and the data will be decoded if all barcode proofing requirements are met.
Interleaved 2 of 5 Interleaved 2 of 5 The following options apply to the Interleaved 2 of 5 (I 2 of 5) symbology. Disable/Enable Interleaved 2 of 5 When this feature is disabled, the scanner will not read Interleaved 2 of 5 barcodes. START / END PROGRAMMING BARCODES Disable Interleaved 2 of 5 DEFAULT Enable Interleaved 2 of 5 Check Digit Calculation When enabled, the scanner will calculate the check digit of the labels.
Symbologies Interleaved 2 of 5 — continued Check Digit Transmit Enable this option to transmit the check digit with scanned barcode data.
Interleaved 2 of 5 Interleaved 2 of 5 — continued Length Control Fixed Length Decoding— When fixed length decoding is enabled, the scanner will decode a barcode if the label length matches one of the configurable fixed lengths. Variable Length Decoding— When variable length decoding is enabled, the scanner will decode a barcode if the label length falls in the range of the configurable minimum and maximum length. Configuring Fixed Length Decoding: 1. Scan the START barcode. 2.
Symbologies Interleaved 2 of 5 — continued Interleaved 2 of 5 Length 1, Length 2 Programming Instructions 1. Scan the START barcode. 2. Scan either the Set Length 1 or Set Length 2 barcode. 3. Turn to Appendix C, Alpha-Numeric Pad and scan the three digits (zero padded) representing the length in decimal notation. NOTE For Interleaved 2 of 5 barcodes, lengths must be an even number. Additionally, all check and data characters are included in the length calculations. 4. Scan the END barcode.
Interleaved 2 of 5 Interleaved 2 of 5 — continued Interleaved 2 of 5 Stitching Enables/disables stitching for Interleaved 2 of 5 labels. When parts of an Interleaved 2 of 5 barcode are presented to the scanner with this feature enabled, the barcode parts will be assembled by the scanner’s software, and the data will be decoded if all barcode proofing requirements are met. Only functions when Fixed Length Decoding is enabled.
Symbologies Interleaved 2 of 5 — continued Minimum Reads This feature specifies the minimum number of consecutive times an Interleaved 2 of 5 label must be decoded before it is accepted as good read.
Codabar Codabar The following options apply to the Codabar symbology. Disable/Enable Codabar When this feature is disabled, the scanner will not read Codabar barcodes. START / END PROGRAMMING BARCODES Disable Codabar DEFAULT Enable Codabar Check Character Verification When enabled, the scanner will verify the check character of the labels.
Symbologies Check Character Transmit Enable this option to transmit the check character with scanned barcode data.
Codabar Codabar — continued Length Control Fixed Length Decoding— When fixed length decoding is enabled, the scanner will decode a barcode if the label length matches one of the configurable fixed lengths. Variable Length Decoding— When variable length decoding is enabled, the scanner will decode a barcode if the label length falls in the range of the configurable minimum and maximum length. Configuring Fixed Length Decoding: 1. Scan the START barcode. 2. Scan the Fixed Length Decoding barcode. 3.
Symbologies Codabar — continued Codabar Length 1, Length 2 Programming Instructions 1. Scan the START barcode. 2. Scan either the Set Length 1 or Set Length 2 barcode. 3. Turn to Appendix C, Alpha-Numeric Pad and scan the three digits (zero padded) representing the length in decimal notation. For Codabar barcodes, all start, stop, check and data characters are included in the length calculations. NOTE 4. Scan the END barcode.
Codabar Codabar — continued Start/Stop Character Type Codabar has four pairs of Start/Stop patterns. Select one pair to match your application. START / END PROGRAMMING BARCODES Start/Stop Type: ABCD/TN*E Start/Stop Type: ABCD/ABCD Start/Stop Type: abcd/tn*e Start/Stop Type: abcd/abcd DEFAULT Start/Stop Character Transmission The transmission of start and end characters of Codabar is selected below.
Symbologies Start/Stop Character Match This feature enables/disables the requirement that start and stop characters match. START / END PROGRAMMING BARCODES Disable Start/Stop Char Match DEFAULT Enable Start/Stop Char Match Codabar Stitching Enables/disables stitching for Codabar labels.
Codabar Codabar — continued Minimum Reads This feature specifies the minimum number of consecutive times a Codabar label must be decoded before it is accepted as a good read.
Symbologies Code 93 The following options apply to the Code 93 symbology. Disable/Enable Code 93 When this feature is disabled, the scanner will not read Code 93 barcodes.
Code 93 Code 93 — continued Length Control Fixed Length Decoding— When fixed length decoding is enabled, the scanner will decode a barcode if the label length matches one of the configurable fixed lengths. Variable Length Decoding— When variable length decoding is enabled, the scanner will decode a barcode if the label length falls in the range of the configurable minimum and maximum length. Configuring Fixed Length Decoding: 1. Scan the START/END barcode. 2. Scan the Fixed Length Decoding barcode. 3.
Symbologies Code 93 — continued Code 93 Length 1, Length 2 Programming Instructions 1. Scan the START barcode. 2. Scan either the Set Length 1 or Set Length 2 barcode. 3. Turn to Appendix C, Alpha-Numeric Pad and scan the three digits (zero padded) representing the length in decimal notation. For Code 93 barcodes, only the data characters are included in the length calculations. NOTE 4. Scan the END barcode.
Code 93 Code 93 — continued Code 93 Stitching Enables/disables stitching for Code 93 barcodes. When parts of a Code 93 label are presented to the scanner with this feature enabled, the barcode parts will be assembled by the scanner’s software, and the data will be decoded if all barcode proofing requirements are met.
Symbologies MSI/Plessey The following options apply to the MSI/Plessey symbology. Disable/Enable MSI/Plessey When this feature is disabled, the scanner will not read MSI/Plessey barcodes. START / END PROGRAMMING BARCODES Disable MSI/Plessey DEFAULT Enable MSI/Plessey Check Digit Verification This feature specifies whether one or two check digits are to be calculated and verified.
MSI/Plessey MSI/Plessey — continued Check Digit Transmit When this option is enabled, the scanner will transmit one-digit or two-digit check digits, depending upon the setting for check digit verification.
Symbologies MSI/Plessey — continued Length Control Fixed Length Decoding— When fixed length decoding is enabled, the scanner will decode a barcode if the label length matches one of the configurable fixed lengths. Variable Length Decoding— When variable length decoding is enabled, the scanner will decode a barcode if the label length falls in the range of the configurable minimum and maximum length. Configuring Fixed Length Decoding: 1. Scan the START/END barcode. 2.
MSI/Plessey MSI/Plessey — continued MSI/Plessey Length 1, Length 2 Programming Instructions 1. Scan the START barcode. 2. Scan either the Set Length 1 or Set Length 2 barcode. 3. Turn to Appendix C, Alpha-Numeric Pad and scan the three digits (zero padded) representing the length in decimal notation. For MSI/Plessey barcodes, all check and data characters are included in the length calculations. NOTE 4. Scan the END barcode.
Symbologies MSI/Plessey — continued MSI/Plessey Stitching Enables/disables stitching for MSI/Plessey barcodes. When parts of an MSI/Plessey label are presented to the scanner with this feature enabled, the barcode parts will be assembled by the scanner’s software, and the data will be decoded if all barcode proofing requirements are met. Only functions when Fixed Length Decoding is enabled.
MSI/Plessey MSI/Plessey — continued Minimum Reads This feature specifies the minimum number of consecutive times an MSI/Plessey label must be decoded before it is accepted as good read.
Symbologies Standard 2 of 5 The following options apply to the Standard 2 of 5 symbology. Disable/Enable Standard 2 of 5 When this feature is disabled, the scanner will not read Standard 2 of 5 barcodes. START / END PROGRAMMING BARCODES Disable Std 2 of 5 DEFAULT Enable Std 2 of 5 Check Digit Verification When enabled, the scanner will verify the check digit of the labels.
Standard 2 of 5 Standard 2 of 5 — continued Check Digit Transmit When this option is enabled, the scanner will transmit the check digit.
Symbologies Standard 2 of 5 — continued Length Control Fixed Length Decoding— When fixed length decoding is enabled, the scanner will decode a barcode if the label length matches one of the configurable fixed lengths. Variable Length Decoding— When variable length decoding is enabled, the scanner will decode a barcode if the label length falls in the range of the configurable minimum and maximum length. Configuring Fixed Length Decoding: 1. Scan the START/END barcode. 2.
Standard 2 of 5 Standard 2 of 5 — continued Standard 2 of 5 Length 1, Length 2 Programming Instructions 1. Scan the START barcode. 2. Scan either the Set Length 1 or Set Length 2 barcode. 3. Turn to Appendix C, Alpha-Numeric Pad and scan the three digits (zero padded) representing the length in decimal notation. For Standard 2 of 5 barcodes, all check and data characters are included in the length calculations. NOTE 4. Scan the END barcode.
Symbologies Standard 2 of 5 — continued Standard 2 of 5 Stitching Enables/disables stitching for Standard 2 of 5 barcodes. When parts of a Standard 2 of 5 label are presented to the scanner with this feature enabled, the barcode parts will be assembled by the scanner’s software, and the data will be decoded if all barcode proofing requirements are met. Only functions when Fixed Length Decoding is enabled.
Standard 2 of 5 Standard 2 of 5 — continued Minimum Reads This feature specifies the minimum number of consecutive times a Standard 2 of 5 label must be decoded before it is accepted as good read.
Symbologies 5-68 Magellan® 1000i
2D Symbologies & Advanced Decoding Features The features in this section are available ONLY for models with 2D features activated.
2D Symbologies & Advanced Decoding Features 2D Symbologies The scanner supports the following 2D symbologies (barcode types): PDF 417 and Datamatrix. Options for each symbology are included in this addendum. Factory Defaults— for the std. RS-232 interface are indicated in bold text throughout. PDF 417 Disable/Enable PDF 417 When disabled, the scanner will not read PDF 417 barcodes.
2D Symbologies PDF 417 — continued Length Control Fixed Length Decoding— When fixed length decoding is enabled, the scanner will decode a barcode if the label length matches one of the configurable fixed lengths. Variable Length Decoding— When variable length decoding is enabled, the scanner will decode a barcode if the label length falls in the range of the configurable minimum and maximum length. Configuring Fixed Length Decoding: 1. Scan the START barcode. 2. Scan the Fixed Length Decoding barcode. 3.
2D Symbologies & Advanced Decoding Features PDF 417 — continued PDF 417 Length 1, Length 2 Programming Instructions 1. Scan the START barcode. 2. Scan either the Set Length 1 or Set Length 2 barcode. 3. Turn to Alpha-Numeric Pad and scan the four hex digits representing the length in hexidecimal notation. For PDF 417 barcodes, only the data characters are included in the length calculations. NOTE Scan the END barcode.
2D Symbologies PDF 417 — continued Minimum Reads This feature specifies the minimum number of consecutive times a PDF 417 label must be decoded before it is accepted as good read.
2D Symbologies & Advanced Decoding Features Datamatrix Disable/Enable Datamatrix When disabled, the scanner will not read Datamatrix barcodes.
2D Symbologies Datamatrix — continued Length Control Fixed Length Decoding— When fixed length decoding is enabled, the scanner will decode a barcode if the label length matches one of the configurable fixed lengths. Variable Length Decoding— When variable length decoding is enabled, the scanner will decode a barcode if the label length falls in the range of the configurable minimum and maximum length. Configuring Fixed Length Decoding: 1. Scan the START barcode. 2. Scan the Fixed Length Decoding barcode.
2D Symbologies & Advanced Decoding Features Datamatrix — continued Datamatrix Length 1, Length 2 Programming Instructions 1. Scan the START barcode. 2. Scan either the Set Length 1 or Set Length 2 barcode. 3. Turn to Alpha-Numeric Pad and scan the four hex digits representing the length in hexidecimal notation. For Datamatrix barcodes, only the data characters are included in the length calculations. NOTE Scan the END barcode.
2D Symbologies Datamatrix — continued Minimum Reads This feature specifies the minimum number of consecutive times a Datamatrix label must be decoded before it is accepted as good read.
2D Symbologies & Advanced Decoding Features Image Capture This function is ONLY available for scanners having a button. Image capture requires that the scanner use the Standard RS-232 or USB COM interface ONLY. NOTE The scanner reverts to default reading mode after image capture and transfer. How to Capture an Image To initiate an Image Capture, scan the IMAGE CAPTURE label below, and press the button. A targeting “pointer” will be illuminated while the button is pressed.
Chapter A Product Specifications Optical and Read Performance Parameters Parameter Specification Scan Volume 70 cubic inches Scan Pattern 100 lines Scan Rate 1,100 digital scan lines Minimum Resolution 5 mil 0 - 6” Depth of Field (100% UPC Labels) Minimum Print Contrast Ratio 25% Skew (Yaw) ± 75 Pitch ± 65 Roll Between 0 and 360 Scanner Dimensions 139.58mm 5.5" 75.44mm 2.97" 97.84mm 3.85" 83.25mm 3.28" 25.4mm 1.
Physical Properties Parameter Specification Dimensions (Scanner only): 3.3” x2.8” x3.7” Dimensions (Scanner w/Base Station): 5.5” x2.9” x3.8” Weight (Scanner) 7.0 oz. Weight (Base Station) 6.6 oz. Electrical Parameters Parameter Operating Voltage Input Current Operating (idle) Operating (label read) Specification (Two Models) 5V unit = 5.0V ± 5% 12V unit = 7-12V <300mA <400 mA Environmental Parameters Parameter Specification Mechanical Shock Multi 1.
Chapter B Cable Pinouts Standard Cable Pinouts (Primary Interface Cables) RS-232 1 2 3 4 5 6 7 8 9 10 CTS RTS RXD TXD 10 Position RJ Pin 1 (Scanner End) VCC IN GND IBM Port 5B/9B/17 1 2 3 4 5 6 7 8 9 10 10 Position RJ DATA DATA + Pin 1 (Scanner End) VCC_IN GND Product Reference Guide B-1
Cable Pinouts USB-OEM 1 2 3 4 5 6 7 8 9 10 10 Position RJ DD+ Pin 1 (Scanner End) VIN GND USB, USB Keyboard & USB COM 1 2 3 4 5 6 7 8 9 10 10 Position RJ DD+ Pin 1 (Scanner End) VBUS_VIN GND Wand Emulation 1 2 3 WAND~ 4 5 6 7 8 VCC_IN 9 GND 10 10 Position RJ Pin 1 (Scanner End) Keyboard Wedge 1 2 3 4 5 6 7 8 9 10 B-2 KB_DATA AT_CLK KB_CLK AT_DATA 10 Position RJ Pin 1 (Scanner End) VCC_IN GND Magellan® 1000i
Chapter C Alpha-Numeric Pad A B C D E F Product Reference Guide C-1
Alpha-Numeric Pad 1 2 3 4 5 6 7 8 9 0 C-2 Magellan® 1000i
Appendix D Default Settings Defaults by Symbology The following is a partial list of key settings for each symbology type.
Interface Default Exceptions The factory default settings indicated in the programming sections (in bold text) reflect factory configuration for the RS-232 standard interface. The following tables list default exceptions by interface for the remaining available interfaces. IBM Interfaces IBM Interfaces include USB-OEM, IBM Port 9B, IBM Port5B and IBM Port17. Parameter D-2 Default Setting IBM Interface Type IBM Port 9B Number of Host Transmit Buffers One Buffer Label I.D.
Interface Default Exceptions Interface Default Exceptions — continued RS-232 Wincor/Nixdorf Parameter Default Setting Interface Type RS-232-WN Number of Host Transmit Buffers One Buffer RS-232 Parity Odd RS-232 Hardware Control CTS Flow Control UPC-E Check Character Conversion Disabled UCC/EAN-128 Label ID ‘P’ Code 39 Label ID ‘M’ Code 93 Label ID ‘L’ Code 128 Label ID ‘K’ Codabar Label ID ‘N’ EAN-8 Label ID ‘B’ EAN-13 Label ID ‘A’ ISBN Label ID ‘A’ Interleaved 2 of 5 Label ID
Interface Default Exceptions — continued Wand Emulation Parameter Default Setting Interface Type Wand Emulation Code 39 Start/Stop Character Transmission Enable Keyboards Keyboard interfaces include USB Keyboard and Keyboard Wedge A-Y.
Appendix E Keyboard Function Key Mappings Keyboard Model Cross Reference summarizes the keyboard models, their defined protocol, scancode set, and some unique features. The remaining tables in this chapter provide the function key maps associated with each of the scancode sets. Table E-1 Table E-1. Keyboard Model Cross Reference Model Type PC/XT Foreign ALT Mode AT; PS/2 25-286; PS/2 30-286; PS/2 50, 50Z; PS/2 60,70,80,90,95 Foreign ALT Mode PS/2 25 and 30 Foreign ALT Mode PC/XT U.S.
Table E-2.
Keyboard Model Cross Reference 1B 1C 1D 1E 1F ESC FS GS RS US ESC F7 F8 F9 F10 76h 83h 0Ah 01h 09h Table E-4.
Table E-5.
Keyboard Model Cross Reference Table E-6.
Table E-7.
Chapter F Host Commands Accepting RS-232 Commands The scanner responds to the following RS-232 commands: COMMAND ASCII HEX COMMENT Enable Scanner E 0x45 Disable Scanner D 0x44 Reset Scanner R 0x52 Not On File Indication F 0x46 Long series of beeps Beep Good Read Tone B 0x42 Beeps if Good Read Beep is enabled Force Good Read Tone ! 0x01 Beeps regardless of beep setting Bel ‘ 0x07 Force Good Read Tone Identification request i 0x69 Returns long responsea Health request h 0x68
NOTES F-2 Magellan® 1000i
Chapter G Sample Symbols UPC-A 0 5 0 1234567890 Interleaved 2 of 5 Code 128 1234567890 Code 128 EAN-13 9 780330 290951 Code 39 BC321 Codabar Code 93 A13579B 123456-9$ Code 2 of 5 123456 Product Reference Guide G-1
Sample Symbols GS1 DataBar Omni- (01)00123456789012 GS1 DataBar Expanded 0100123456789050 G-2 Magellan® 1000i
ASCII Chart ASCII Char. Hex No. ASCII Char. Hex No. ASCII Char. Hex No. ASCII Char. Hex No. NUL SOH STX ETX EOT ENQ ACK BEL BS HT LF VT FF CR SO SI DLE DC1 DC2 DC3 DC4 NAK SYN ETB CAN EM SUB ESC FS GS RS US 00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F 10 11 12 13 14 15 16 17 18 19 1A 1B 1C 1D 1E 1F SP ! “ # $ % & ’ ( ) * + , .
Australia Datalogic Scanning Pty Ltd Telephone: [61] (2) 9870 3200 australia.scanning@datalogic.com Japan Datalogic Scanning KK Telephone: 81 (0)3 3491 6761 japan.scanning@datalogic.com France and Benelux Datalogic Scanning Sarl Telephone: [33].01.64.86.71.00 france.scanning@datalogic.com Latin America Datalogic Scanning, Inc Telephone: (305) 591-3222 latinamerica.scanning@datalogic.com Germany Datalogic Scanning GmbH Telephone: 49 (0) 61 51/93 58-0 germany.scanning@datalogic.
