Operation Manual
Table Of Contents
- Introduction
- Setup
- Configuration Using Bar Codes
- Configuration Parameters
- Global Interface Features
- RS-232 Interface
- RS-232/USB-Com Interfaces
- Keyboard Settings
- USB-OEM Interface
- IBM 46XX Interface
- Wand Emulation Interface
- Data Format
- Reading Parameters
- Double Read Timeout
- LED and Beeper Indicators
- Scanning Features
- Scan Mode
- Stand Mode Indication
- Stand Operation
- Pick Mode
- Stand Mode Sensitivity
- Stand Mode Illumination Off Time
- Scanning Active Time
- Stand Illumination Control
- Motion Still Timeout
- Flash On Time
- Flash Off Time
- Aiming Pointer
- Aiming Duration Timer
- Green Spot Duration
- Mobile Phone Mode
- Partial Label Reading Control
- Decode Negative Image
- Image Capture
- Corded Only Features
- Multiple Label Reading
- 1D Symbologies
- 1D Code Selection
- Disable All Symbologies
- Code EAN/UPC
- UPC-E
- GTIN Formatting
- EAN 13 (Jan 13)
- ISSN
- EAN 8 (Jan 8)
- UPC/EAN Global Settings
- Add-Ons
- Code 39
- Trioptic Code
- Code 32 (Ital Pharmaceutical Code)
- Code 39 CIP (French Pharmaceutical)
- Code 39 Danish PPT
- Code 39 LaPoste
- Code 39 PZN
- Code 128
- GS1-128
- Code ISBT 128
- Interleaved 2 of 5 (I 2 of 5)
- Interleaved 2 of 5 CIP HR
- Follett 2 of 5
- Standard 2 of 5
- Industrial 2 of 5
- Code IATA
- Codabar
- ABC Codabar
- Code 11
- GS1 DataBar™ Omnidirectional
- GS1 DataBar™ Expanded
- GS1 DataBar™ Limited
- Code 93
- MSI
- Plessey
- 2D Symbologies
- WIRELESS FEATURES
- Bluetooth-Only Features
- FEATURES FOR STAR MODELS ONLY
- Motion Features
- References
- Message Formatting
- Technical Specifications
- Standard Defaults
- Sample Bar Codes
- Keypad
- Scancode Tables
Product Reference Guide
203
2D SYMBOLOGIES
2D Global Features
• 2D Maximum Decoding Time, page
204
• 2D Normal/Inverse Symbol Control,
page 205
• 2D Structured Append, page 205
The reader supports the following 2D symbologies (bar code ty
pes). Symbology-dependent
options for each symbology are included in this chapter. See "1D Code Selection" starting on
page 111
for configuration of 1D bar codes.
2D Symbologies
• Aztec Code, page 206 • Micro PDF417, page 221
• China Sensible Code, page 209 • QR Code, page 224
• Data Matrix, page 212 • Micro QR Code, page 227
• Maxicode, page 215 • UCC Composite, page 230
• PDF417, page 218 • Postal Code Selection, page 232
2D Global Features
The following features are common to all, or in some cases, most of the available 2D
symbologies. Default settings are indicated at each feature/option with a green arrow. Also
reference Appendix B, Standard Defaults for a listing of the most widely used set of standard
factory settings. That section also provides space to record any custom settings needed or
implemente
d for your system.
To set most features:
1. Scan the ENTER/EXIT PROGRAMMING bar code at the top of applicable p
rogram-
ming pages.
2. Scan the correct bar code to set the desired programming feature or parameter. You may
need to cov
er unused bar codes on the page, and possibly the facing page, to ensure that
the reader reads only the bar code you intend to scan.
3. If additional input parameters are needed, go to Appendix D, Keypad, and scan the
appropriate characters from the keypad.
Additional information about many features can be found in the “Refer-
ences” chapter.
If you make a mistake before the last character, scan the CANCEL bar code
to
a
bort and not save the entry string. You can then start again at the
beginning.
Complete the programming sequence by scanning the ENTER/EXIT PROGRAMMING bar
code to exit Programming Mode.