Gryphon™ L GD4300 General Purpose Corded Handheld Laser Bar Code Reader Quick Reference Guide
Datalogic Scanning, Inc. 959 Terry Street Eugene, Oregon 97402 Telephone: (541) 683-5700 Fax: (541) 345-7140 An Unpublished Work - All rights reserved. No part of the contents of this documentation or the procedures described therein may be reproduced or transmitted in any form or by any means without prior written permission of Datalogic Scanning, Inc. or its subsidiaries or affiliates ("Datalogic" or “Datalogic Scanning”).
Table of Contents Gryphon L GD4300 Quick Reference Guide .................................1 End User License Agreement ............................................................1 Software Product Policy...................................................................... 5 Customers Under Software Support ...................................5 Technical Features ................................................................................ 6 Connect/Disconnect Cable......................................
NOTES
Gryphon L GD4300 Quick Reference Guide Datalogic Scanning, Inc. GRYPHON™ PRODUCT SERIES END USER LICENSE AGREEMENT Notice to End User: The Datalogic Product you have acquired contains embedded Software, which is integral to the product's operation. This Software is being provided to you under license, subject to the terms and conditions of this Agreement. If you use the Datalogic Product, you will be deemed to have accepted the terms and conditions of this Agreement.
2.2 chase" or its equivalents when applied to the Software shall mean "acquire under license." End User is not entitled to receipt or use of the source code to any Software.
6.2 reports according to Datalogic's standard assistance practices. Datalogic does not warrant that the product will meet End User's requirements or that use of the product will be uninterrupted or error free, or that Datalogic's remedial efforts will correct any nonconformance.
9.2 If End User is using the Datalogic Product outside of the United States, End User must comply with the applicable local laws of the country in which the Datalogic Product is used, with U.S. export control laws, and with the English language version of this Agreement. The provisions of the "United Nations Convention on International Sale of Goods" shall not apply to this Agreement. 10. Termination. 10.1 10.
Software Product Policy Software Product Policy Datalogic reserves the right to ship its products with the latest version of software/firmware available. This provides our customers with the very latest in Datalogic software technology. The only exception to this policy is when the buyer has a signed contract with Datalogic that clearly defines the terms and conditions for making software/firmware changes in products shipped to the buyer.
Technical Features Technical Features Item Description Physical Characteristics Color White/Grey Black/Grey Dimensions Height 7.1” / 181mm Length 3.9” / 100mm Width 2.8” / 71mm Weight (without cable) Approximately 6.0 ounces/169 g Electrical Characteristics Voltage & Current GD4330 model: Input current at 5V±5% = 260 mA (max) 2.5 mA (USB suspend) Standby (typical) 30mA GD4310 model: Input Power = 1.2W max in the 4.5÷14V range 2.
Technical Features Interfaces Supported RS-232 Std., RS-232 Wincor-Nixdorf, RS-232 OPOS, IBM 46xx (ports5B and 9B), USB Com Std., USB Keyboard, USB Alternate Keyboard,USB OEM, Keyboard Wedge (AT with or w/o Alternate Key, IBM AT PS2 with or w/o Alternate Key, PC-XT, IBM 3153, IBM Terminals 31xx, 32xx,34xx, 37xx make only and make break keyboard, Digital Terminals VT2x, VT3xx, VT4xx, and Apple) and Wand Emulation.
Connect/Disconnect Cable 1 Connect/Disconnect Cable 2 Connect Host Interface Keyboard Wedge Interface RS-232 Interface 8 Gryphon™ L GD4300
Aim and Scan USB Interface 3 Aim and Scan 012345 012345 The area shown in green below illustrates the area of typical maximum performance for the scanner.
Parts of the Reader Parts of the Reader LED Scan Window Trigger Scanning Modes The reader can operate in one of several scanning modes: Trigger Single — When the trigger is pulled, scanning is activated until one of the following occurs: - a programmable duration1 has elapsed - a label has been read - the trigger is released This mode is associated with typical handheld reader operation: when the trigger is pulled, scanning starts and the product scans until the trigger is released, or a label is read, o
Scanning Modes Flashing — The reader flashes1 on and off regardless of the trigger status. Always On — No trigger pull is required to read a barcode. Scanning is continually on2. Stand Mode — No trigger pull is required to read a barcode. Scanning is alternatively turned on and off. Scan Mode = Trigger Single Scan Mode = Trigger Hold Multiple Scan Mode = Trigger Pulse Multiple 1. 2. Controlled by Flash On Time and Flash Off Time. Use the PRG to program these options.
Scanning Modes Scanning Modes — continued Scan Mode = Flashing Scan Mode = Always On Scan Mode = Stand Mode 12 Gryphon™ L GD4300
Troubleshooting Troubleshooting Problem Possible Cause Nothing happens when the scan button is No power to the reader. pulled. Possible Solutions Check system power. Ensure power supply is connected. Interface or power cables Ensure all cable connections are loose. are secure. Laser comes on, but barcode does not decode. Ensure reader is programmed to read the type Reader not programmed of barcode scanned. Refer to for correct barcode type. the Product Reference Guide (PRG) for more information.
LED and Beeper Indications LED and Beeper Indications The reader’s beeper sounds and its LED illuminates to indicate various functions or errors on the reader. A “Green Spot” also lights to indicate a good read. The tables below list these indications. One exception to the behaviors listed in the tables is that the reader’s functions are programmable, and may or may not be turned on. For example, certain indications, such as the power-up beep can be disabled using programming barcode labels.
Programming Barcodes Programming Barcodes For your convenience, this guide includes the programming barcodes required to configure the reader for use with different interface (terminal/host) types. See the Product Reference Guide (PRG) for more complete information about programming and configurable features. You can download the latest version of the PRG and any other available publications for the reader from the website listed on the back cover of this manual.
Programming Barcodes RS-232 Interface To use an RS-232 interface, scan the barcode for the desired RS-232 host type.
Programming Barcodes USB Interface The reader attaches directly to a USB host, or a powered USB hub, and is powered by it. No additional power supply is required. When using a USB interface, the reader auto-detects the USB cable and defaults to either the USB keyboard interface (GD4330) or USB-OEM interface (GD4310).
Programming Barcodes Keyboard Wedge Interface To use a Keyboard Wedge interface, scan the barcode for the desired keyboard type.
Programming Barcodes Keyboard Wedge Interface — continued Select KBD-XT (PC/XT w/Standard Key Encoding) Select KBD-IBM-3153 (for IBM Terminal 3153) Select KBD-IBM-M (for IBM Terminals 31xx, 32xx, 34xx, 37xx make only keyboard) Select KBD-IBM-MB (for IBM Terminals 31xx, 32xx, 34xx, 37xx make break keyboard) Select KBD-DIG-VT (for DIGITAL Terminals VT2xx, VT3xx, VT4xx) Quick Reference Guide 19
Ergonomic Recommendations Ergonomic Recommendations CAUTION • To avoid or minimize the potential risk of ergonomic injury, follow the recommendations below. Consult with your local Health & Safety Manager to ensure that you are adhering to your company’s safety programs to prevent employee injury.
Regulatory Information Laser Safety Compliance The laser scanner conforms to the applicable requirements of both CDRH 21 CFR 1040 and EN60825-1 at the date of manufacture. The laser light is visible to the human eye and is emitted from the output window. Use of controls or adjustments or performance of procedures other than those specified herein may result in exposure to hazarouds visible laser light. CAUTION The laser scanner utilizes a low-power laser diode.
22 X X X ⬉䏃ᵓ㒘ӊ ܝᄺ㒘ӊ ܝᄺ㒘ӊ Printed Circuit Board Assembly Assy, Optics Block Assy, Module O O O ᳮ Mercury (Hg) O O O 叏 Hexavalent Chromium (Cr(VI)) O O O ચ卲 O O O ᄙᄽ侶 O O O ᄙᄽԲㅘ Polybrominated diphenyl ethers (PBDE) China RoHS Polybrominated biphenyls (PBB) Ქኂ‛凝ᚗర⚛ Cadmium (Cd) O ઍᱝẊㇱઙ⊛ᚲဋ凝ޗறխࢬܶऱ具Ẋڶڶ୭ढ凝݁܅Պխ䦀Գا٥ࡉ㧺ॾஒ䣈䢓ຝᚲ咒ؒ⊛ ޝ䶣ॾஒ䣈խڶڶ୭ढ凝ऱૻၦޣρ(SJ/T 11363-2006) 億ࡳऱૻၦޕ X: ઍᱝẊㇱઙᚲ↪⊛ဋ凝ޗறխ, ⥋ዋ৻㮕᧚ᢱᚲ⊛Ქኂ‛凝Պխ䦀Գا٥ࡉ㧺ॾஒ䣈䢓ຝᚲ咒ؒ⊛ ޝ䶣ॾஒ䣈խڶڶ୭ढ凝
Regulatory Information Radio Frequency Interference Requirements This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Reader Labeling Reader Labeling Labels are shown here to illustrate their location only. Please view the labels on your product for actual details. Regulatory & Serial Numbers Waste Electrical and Electronic Equipment (WEEE) Statement English For information about the disposal of Waste Electrical and Electronic Equipment (WEEE), please refer to the website at www.scanning.datalogic.com.
Reader Labeling Warranty Datalogic warrants to Customer that Datalogic's products will be free from defects in materials and workmanship for a period of 5 years from product shipment. This warranty does not extend to batteries and cables. As consumable items batteries and cables carry a 90 day warranty from time of purchase for DOA (dead on arrival) defects.
Reader Labeling NOTES 26 Gryphon™ L GD4300
DECLARATION OF CONFORMITY 09 Datalogic Scanning Group Srl Via S.
Australia Datalogic Scanning Pty Ltd Telephone: [61] (2) 9870 3200 australia.scanning@datalogic.com Japan Datalogic Scanning KK Telephone: 81 (0)3 3491 6761 japan.scanning@datalogic.com France and Benelux Datalogic Scanning SAS Telephone: [33].01.64.86.71.00 france.scanning@datalogic.com Latin America Datalogic Scanning, Inc Telephone: (305) 591-3222 latinamerica.scanning@datalogic.com Germany Datalogic Scanning GmbH Telephone: 49 (0) 61 51/93 58-0 germany.scanning@datalogic.
