Lynx™ Personal Digital Assistant (PDA) www.datalogic.com © 2012-2013 Datalogic ADC S.r.l. All rights reserved. Datalogic and the Datalogic logo are registered trademarks of Datalogic S.p.A. In many countries, including the U.S.A. and the E.U. Datalogic ADC S.r.l. Via S.
Datalogic ADC S.r.l. Via S. Vitalino, 13 40012 Lippo di Calderara di Reno Bologna - Italy Telephone: (+39) 051-3147011 Fax: (+39) 051-3147205 ©2012-2014 Datalogic ADC S.r.l. An Unpublished Work - All rights reserved. No part of the contents of this documentation or the procedures described therein may be reproduced or transmitted in any form or by any means without prior written permission of Datalogic ADC, Inc. or its subsidiaries or affiliates ("Datalogic" or “Datalogic ADC”).
CONTENTS REFERENCES ............................................................................................ vi Conventions ..................................................................................................vi Reference Documentation ............................................................................vi Services and Support ....................................................................................vi GENERAL VIEW ...........................................................
.6 4.6.1 4.6.2 4.6.3 4.6.4 4.6.5 4.6.6 4.6.7 4.6.8 4.7 4.7.1 4.7.2 4.8 4.8.1 4.8.2 4.8.3 4.9 4.10 4.11 4.11.1 4.11.2 4.11.3 4.11.4 4.11.5 4.12 4.13 4.13.1 4.14 4.14.1 4.14.2 4.14.3 4.14.4 Settings ....................................................................................................... 49 Data Capture Configuration ........................................................................ 50 Decoding configuration pages.....................................................................
Bluetooth® Approval ................................................................................. 140 FCC Compliance ....................................................................................... 142 RF Exposure Information (SAR) ............................................................... 143 Industry Canada Compliance .................................................................... 144 SAR Compliance.......................................................................................
1 REFERENCES CONVENTIONS This manual uses the following conventions: “User” refers to anyone using an Lynx PDA. “PDA” and "Lynx" refer to Lynx PDA. “You” refers to the System Administrator or Technical Support person using this manual to install, configure, operate, maintain or troubleshoot an Lynx PDA. “Single Dock” refers to the Lynx Single Slot Dock. The label artworks may be only a draft. Refer to the product labels for more precise information.
GENERAL VIEW B C I D L K J A N E O Q M F H Q G A) B) C) D) E) F) G) H) Color Display ON/OFF Power Key Receiver LEDs Front Scan Key Keyboard Microphone Telescope Stylus (not included in the box, please order it separately, p/n 94ACC0068) I) J) K) L) M) N) O) P) Q) Laser Safety Label Loudspeaker Color Camera Flash Product Label (under battery) MicroSD Card Slot (under battery) SIM Card Slot (under battery) Reset Key (under battery) Guitar Pick vii
1 T R U S R) Side Scan Key (right) S) Up/down Volume Keys V T) Side Scan Key (left) U) Headset Connector V) Micro-USB Port for supplying power and data transfer (host/slave) W W) Data Capture Window viii X X) Handylink™ Connector (host/slave)
INTRODUCTION 1 1.1 1 INTRODUCTION LYNX DESCRIPTION The Lynx contains the most innovative technical features, providing them to the user in an ergonomic and elegant form factor. The accelerometer, the vibrator alert and the 3 LEDs help to not waste time in the configuration and usage of the product. Working with the Lynx becomes an easy pleasure. Great aesthetics do not put the robustness on a second level.
1 LYNX™ 1 1.2 AVAILABLE MODELS The Lynx is available in different models depending on the options it is equipped with. All options are listed below: • communication options: 802.11 b/g/n radio, Bluetooth®, HSPA+ • data capture options: laser, 2D imager • • operating system: Windows Embedded Handheld keyboard options: numeric, QWERTY For further details about the Lynx models refer to the web site: http://www.datalogic.
INTRODUCTION • 1 944400006 Lynx 00N0WI-1Q1-MEN0 Lynx with Bluetooth® v2.0, 802.11 b/g/n CCX v4, 2D Imager, Camera 3MPixel,Windows Embedded Handheld 6.
1 LYNX™ 1 1.
INTRODUCTION 1 Rechargeable battery packs are not initially fully charged. Therefore the first operation to perform is to charge them. See paragraph 2.1.
1 LYNX™ 1 1.4 INSERTING A MICROSD CARD Lynx supports microSD memory cards. To access the microSD card slot and insert the card, proceed as follows: 1. Turn off the Lynx. 2. Shift the battery latch to the left and remove the battery pack: 3.
INTRODUCTION 1 4. Shift the card to the right to lock it into the cardholder; close the card slot: 5. First insert the bottom (contacts) and then the upper side of the battery pack into the slot. Press until the battery latch clicks.
1 LYNX™ 1 1.4.1 Removing the MicroSD Card To remove the microSD card, follow the steps above to access the microSD card cage under the battery, and remove it from the microSD slot. Follow proper ESD precautions to avoid damaging microprocessors in the Lynx or the microSD card itself. CAUTION the Proper ESD precautions include, but are not limited to, working on an ESD mat and ensuring that the operator is properly grounded. Do not force the card.
INTRODUCTION 1.5 1 INSTALLING THE SIM CARD To correctly insert the SIM Card, proceed as follows: 1. Turn off the Lynx. 2. Shift the battery latch to the left and remove the battery pack: 3. Insert the SIM card with the contacts downwards: 4. First insert the bottom (contacts) and then the upper side of the battery pack into the slot. Press until the battery latch clicks.
1 LYNX™ 1 Follow proper ESD precautions to avoid damaging the SIM card. Proper ESD precautions include, but are not limited to, working on an ESD mat and ensuring that the operator is properly grounded. CAUTION Do not force the card. If you feel resistance, remove the card, check the orientation, and reinsert it. Do not use the SIM card slot for any other accessories. 1.5.1 Removing the SIM Card To remove the SIM card, follow the steps above to access the SIM area, and remove it from its slot.
INTRODUCTION 1.6 1 ACCESSORIES General Accessories 94ACC0067 Stylus,Guitar Pick W/ Cord (5 pcs),Lynx 94ACC0068 Stylus,Telescopic W/ Cord (5 pcs), Lynx 94ACC0069 Lanyard (5 pcs), Lynx 94ACC0070 Belt Holster, Lynx 94ACC0072 Screen Protect, 2.
1 LYNX™ 1 Power Supplies/Cords 94ACC1150 Power Cord, 3 pin (Euro Plug) - 5 pcs 94ACC1381 Power Supply, Dock, PWR Plug 2.1mm 94ACC1385 Power Supply, Charger, MBC And Dock 95A051041 Power Cord, AC, IEC/EUR 95ACC1113 Power Cord, 120V AC, IEC/US 95ACC1212 Power Cord, IEC/Japan 95ACC1213 Power Cord, 240V AC, UK 95ACC1215 Power Cord, IEC/Australian 95ACC1284 Power Cord, IEC C13, Black Argentina, ROHS NOTE 12 Use only a Datalogic approved power supply and cables.
BATTERIES AND MAINTENANCE 2 2 BATTERIES AND MAINTENANCE NOTE Rechargeable backup batteries and battery packs are not initially fully charged. Therefore the initial operation to perform is to charge them. See below. Annual replacement of rechargeable battery pack avoids possible risks or abnormalities and ensures maximum performance. CAUTION 2.
2 1 LYNX™ Moreover recharging is possible by USB direct connection with the host computer, but with longer charging times. Insert the micro-USB cable output plug into the micro-USB connector of the Lynx, making sure that the arrow on the plug faces upwards: NOTE During the charging process the LED positioned at the right side of the display glows red constantly. Once the charging process has been completed this LED glows green constantly.
BATTERIES AND MAINTENANCE NOTE 2 The battery level may not be displayed correctly for some minutes after the disconnection if the Lynx is disconnected from power supply before the charging cycle is completed. The Lynx may get warm during charging; this is normal and does not mean a malfunction. NOTE Use only a USB-IF compliant USB port as a charging source.
1 LYNX™ 2 2.2 REPLACING THE BATTERY PACK To correctly replace the battery pack, proceed as follows. 1. Turn off the Lynx. 2. Shift the battery latch to the left and remove the battery pack: 3. Install the new battery pack, first insert the bottom (contacts) and then the upper side of the battery pack into the slot. Press until the battery latch clicks.
BATTERIES AND MAINTENANCE 2 Installing, charging and/or any other action should be done by authorized personnel and following this manual. WARNING The battery pack may get hot, explode, ignite, and/or cause serious injury if exposed to abusive conditions. If the battery pack is replaced with an improper type, there is risk of explosion and/or fire.
1 LYNX™ 2 WARNING Do not disassemble or modify (i.e. bend, crush or deform) the battery pack. The battery pack contains safety and protection devices, which, if damaged, may cause the battery pack to generate heat, explode or ignite. In case of leakage of liquid from the battery, avoid contact with liquid the skin or eyes. If the contact occurs, immediately wash the affected area with water and consult a doctor. Do not solder directly onto the battery pack. Do not expose the battery pack to liquids.
BATTERIES AND MAINTENANCE 2.3 2 CLEANING THE PDA Periodically clean the Lynx with a slightly dampened cloth. Do not use alcohol, corrosive products or solvents.
1 LYNX™ 3 3 CONNECTIONS 3.1 USB CONNECTION You can use the standard micro USB cable 94A051968 or the Datalogic HandyLink™ cable 94A051970 to directly connect the Lynx to a host computer to transfer data through the USB interface. A C B Key: A Host computer B Standard Micro USB cable 94A051968/ 94A051970 HandyLink™ USB Client Cable C Lynx Connection through the cable complies to the USB 1.1 standard.
CONNECTIONS 3 The Single Dock can be connected to the Host by means of the Micro-B USB cord 94A051968. Once the host computer has been turned on, insert the Lynx PDA into the cradle. A C B D Key: A Host computer C 94A150036 Lynx Single Slot Dock B 94A051968 Micro USB Client Cable D 94ACC1381 Power Adapter Connection through the cradle complies to USB 1.1 standard. NOTE The actual data transfer speed can be appreciably lower than the maximum theoretical speed.
1 LYNX™ 3 3.2 CONNECTION TO USB PERIPHERALS To connect the Lynx to a USB keyboard or a memory device, connect the terminal to the Datalogic 94A051969 cable or to the Datalogic 94A051971 cable (together with a standard A to micro A USB cable). For all these devices maximum current draw must be less than 100mA.
CONNECTIONS 3 Insert the micro-USB cable output plug into the micro-USB connector of the Lynx, making sure that the arrow on the plug faces upwards: NOTE 23
1 LYNX™ 3 Connect the Single Slot Dock to the peripheral by means of a Micro-A USB cord, or use a Micro-A to Std-A receptacle USB adapter such as Datalogic 94A051969 (together with a standard USB cable if needed). B A C D E A USB Peripheral (memory) D Standard A to Micro A USB Cable B Lynx Single Slot Dock E 94ACC1381 Power Adapter C 94A051969 Micro USB Host Cable NOTE Lynx works with most of the mentioned USB peripherals.
CONNECTIONS 3.
1 LYNX™ 3 The Single Slot Dock can be connected to the Host by means of a standard null modem cable such as Datalogic 94A051020 CAB-427 for 9-pin connections. Once the Host computer has been turned on, insert the Lynx PDA into the cradle.
CONNECTIONS 3.4 3 WLAN CONNECTION Lynx 802.11 b/g/n radio models can communicate with the host using the on-board Wi-Fi radio and an Access Point connected to the host computer network. For models using the 802.11 b/g/n radio, you can find information about the applet for radio configuration: http://www.summitdata.com/SCU.htm. To launch this utility you can tap the specific icon if it is visible on the taskbar or you can select the menu item: Start > Summit and tap the ‘SCU’ icon.
3 1 LYNX™ 802.11 b/g/n radio module is on by default, in order to avoid wasting energy, you can switch it off using SCU. NOTE NOTE NOTE Suspending the terminal powers off the 802.11 b/g/n radio and drops the radio connection. When the terminal resumes, depending on the radio power mode and security protocol selected, it may take up to 30 seconds for the 802.11 b/g/n radio driver to re-associate the radio to the network.
CONNECTIONS 3.5 3 WPAN CONNECTIONS Lynx Bluetooth® models can communicate with a Bluetooth® device, such as a printer, within a range of 10 m, using the on-board Bluetooth® module. B A Key: A) Lynx B) Bluetooth® printer NOTE In order to extend battery life, the Bluetooth® module is off by default. If you need to have Bluetooth® working, the module must be powered on using the Wireless Communications applet (see par. 4.6.6), and perform the Discovery procedure (see par. 4.7.2).
1 LYNX™ 3 3.6 WWAN CONNECTION Lynx 3G/4G HSPA+ models enhance your connectivity solutions giving you an opening to an international wireless infrastructure that is the global standard. Lynx uses the following bands: UMTS/HSPA+: 800/850/900/1900/2100MHz GSM/GPRS/EDGE 850 900 1800 1900 MHz. In order to use a WWAN Connection you have to install a SIM Card (see instructions on par. 1.5). NOTE NOTE In order to avoid wasting energy, the phone module is off by default.
CONNECTIONS 3 Calls can be made or received using the Lynx as a phone handset, using the Lynx headset or using a Bluetooth® headset. NOTE During a call, you can set the speaker volume by pressing the volume keys on the side of the Lynx. NOTE In case of heavy usage the Lynx may get warm; this is normal and does not mean a malfunction.
1 LYNX™ 3 3.7 WIRELESS AND RADIO FREQUENCIES WARNINGS Use only the supplied or an approved replacement antenna. Unauthorized antennas, modifications or attachments could damage the product and may violate laws and regulations. The antennas inside the Lynx are not user-accessible and cannot be replaced by end users. Send any faulty equipment to Datalogic for repair. WARNING Most modern electronic equipment is shielded from RF signals.
CONNECTIONS 3 WARNING RF signals may affect improperly installed or inadequately shielded electronic systems in motor vehicles. Check with the manufacturer or its representative regarding your vehicle. You should also consult the manufacturer of any equipment that has been added to your vehicle. WARNING An air bag inflates with great force. DO NOT place objects, including either installed or portable wireless equipment, in the area over the air bag or in the air bag deployment area.
1 LYNX™ 4 4 USE AND FUNCTIONING The use of the Lynx depends on the application software loaded. However there are several parameters that can be set and utilities that can be used to perform some basic functions such as data capture, communications, file management, etc 4.1 STARTUP The Lynx turns on when the battery pack or the external supply is inserted and the ON/OFF Power button is pressed. After the battery pack is installed, use the [ON/OFF] key to turn the PDA on and off.
USE AND FUNCTIONING 4 The PDA can also be awakened or turned off by applications. NOTE 4.1.1 Using the Stylus The stylus selects items and enters information. The stylus functions like a mouse. Tap: Touch the screen once with the stylus to open items and select options. Drag: Hold the stylus on the screen and drag across the screen to select text and images. Drag in a list to select multiple items. Tap-and-hold: Tap and hold the stylus on an item to see a list of actions available for that item.
1 LYNX™ 4 4.2 WINDOWS EMBEDDED HANDHELD WELCOME WIZARD In Windows Embedded Handheld, at the very first Lynx startup, following a clean boot or following a Registry restore to default values, the PDA startup (see par. 4.1) is preceded by the Welcome Wizard. Welcome Wizard Screen The Welcome Wizard allows the user to calibrate the touch screen (see par. 4.6.7).
USE AND FUNCTIONING 4.3 4 DATA CAPTURE To capture data first of all tap Start > Settings > System > Decoding: To configure and enable data capture parameters refer to par. 4.6.1.
1 LYNX™ 4 4.3.1 Laser Data Capture To scan barcodes, point the Lynx laser model onto the code from a distance within the reading range while pressing the SCAN key. The lighted band emitted by the laser must completely cross the barcode as shown in the figure below. If the scan has taken place correctly: − − 38 the Good Read LED glows steadily Green for a configurable time; if enabled, the Good Read Beep plays.
USE AND FUNCTIONING 4 Remove the protective film cover over the Laser Output Window before use, if present.
1 LYNX™ 4 4.3.2 Imager Data Capture The Lynx Imager captures a picture of the entire bar code. The omni-directional scanning does not require that the operator orient the bar code to align with the scan pattern. To read a 1D or 2D code, simply point the Lynx Imager model onto the code and press the SCAN Key.
USE AND FUNCTIONING Linear barcode 4 2D Matrix symbol ÌBX3ÉÎ Relative Size and Location of Aiming System Pattern The field of view changes its size as you move the reader closer or farther away from the code. The field of view indicated by the aiming system pattern will be smaller when the Lynx Imager is closer to the code and larger when it is farther from the code. Symbologies with smaller bars or elements (mil size) should be read closer to the unit.
1 LYNX™ 4 4.4 DESCRIPTION OF THE KEYS The Lynx comes with two different keyboards, an alphanumeric keyboard (QWERTY), having 46 keys, and a numeric keyboard, having a total of 27 keys. 4.4.
USE AND FUNCTIONING 4 Numeric Keyboard 43
1 LYNX™ 4 Main Keys Function KEY FUNCTION Pressing the SCAN key starts barcode data capture. Pressing cursor keys lets you move forwards, backwards, upwards or downwards within text fields, scroll through a Menu list or browse among folder files. Yellow modifier (toggle key): when pressed before a standard key, it enables the character or function printed in yellow above the key.
USE AND FUNCTIONING 4.4.2 4 Resetting the Lynx There are several reset methods for the Lynx. A warm boot terminates an unresponsive application and clears the working RAM, but preserves the file system. Registry is restored from persistent memory if available or returned to factory default. A cold boot forces all applications to close, completely reinitializing the system. It clears the working RAM, but the file system is preserved. Registry is restored from persistent memory.
1 LYNX™ 4 Clean Boot To perform a clean boot, do the following steps: 1. 2. Perform a Warm Boot (see Warm Boot) Before the splash screen appears, press and hold down the 0 and Telephone End keys simultaneously: A dialog box will appear asking for confirmation. Press the Enter Key to confirm. If you wish to cancel the clean boot, press Esc by pressing Blue + Telephone End.
USE AND FUNCTIONING 4.5 4 STATUS INDICATORS 4.5.1 LED Status The Lynx provides three different LEDs signaling the PDA status. LED STATUS Good Read Red (right side) Charging Status (left side) Keyboard Status (center) Scanning LED is ON from the time the user hits the scan button or side trigger buttons until the bar code is decoded. Green Scanning LED is ON, showing a good decode. Green It is constant once the charging process has been completed (full charge).
1 LYNX™ 4 4.5.2 Taskbar The Taskbar provides information about the time, the battery level, the keyboard function, and the decoding status. Windows Embedded Handheld Taskbar ICONS DESCRIPTION Zooms the screen. Opens the Connections balloon, which includes hypertext links to the Wireless Manager and the Connections applet. (see par. 4.6.6). Displays the battery status.
USE AND FUNCTIONING 4.6 4 SETTINGS From the Start menu, tap Settings. The settings are organized hierarchically.
1 LYNX™ 4 4.6.1 Data Capture Configuration You can configure the Lynx’s decoding options by tapping Start -> Settings -> System -> Decoding: There are two sections in the Decoding control panel, each containing additional pages. There are seven General Configuration pages and multiple Barcode symbology pages. DECODING CONFIGURATION PAGES Select the desired configuration from the options shown in the figure below, and the other Decoding Properties figures on the following pages.
USE AND FUNCTIONING 4 Audio From the Decoding menu, tap Configure > General > Audio. Use it to set volume, tone, duration, and number of various types of beeps. Good Read From the Decoding Properties applet, tap Configure > General > Good Read. Use it to enable Good Read indications, the use of a vibrator feedback and to set the decoding timeout for decoding labels.
4 1 LYNX™ General Options From the Decoding menu, tap Configure > General > General Options. Select from Label Programming Enable, Symbology IDs, Label Prefix, Label Suffix and Data Separator.
USE AND FUNCTIONING 4 Decoding Options From the Decoding Properties applet, tap Configure > General > Decoding Options. Use it to configure the User ID for symbologies, Redundancy and Aggressive Decoding (if supported by the decoding module). Select a symbology to view or change the available properties settings.
4 1 LYNX™ Spot Beam From the Decoding Properties applet, tap Configure > General > Spot Beam. It allows enabling and configuration of Spot Beam and triggering modes. It is only available on devices equipped with laser and advanced long range laser decoding modules that support the Spot Beam Feature.
USE AND FUNCTIONING 4 Imager Options From the Decoding Properties applet, tap Configure > General > Imager Options. It configures illumination, target beam and Pick List mode, and triggering modes. It is only available on devices equipped with 2D decoding engines.
4 1 LYNX™ Devices From the Decoding Properties applet, tap Configure > General > Devices. Use it to enable or disable the keyboard wedge for Barcode scanner. Also use it to enable or disable the Clipboard mode for passing decoding data to a receiving application. When the Clipboard checkbox is checked, the Windows clipboard is used to pass label data, which can be much faster than the keyboard wedge at typing label data from a large label one character at a time.
USE AND FUNCTIONING 4 1D Barcode Symbology Pages Use the drop-down menus from Configure > 1D Barcode, or tap the left and right arrow keys to navigate the different pages of the barcode symbology pages. Each barcode symbology opens to its own page, as shown in the figure below. Refer to the sample symbology control panels for examples of the types of fields and options you can modify. Codabar: Select Enable, Min/Max Lengths, Enable Checksum, Send Checksum, Send Start/Stop and Convert to CLSI.
4 1 LYNX™ Decoding Settings Select from the Decoding Properties Settings menu to restore previous configurations and/or other available default settings. Choose from: • Factory Defaults • Minimum Settings • Maximum Settings • Save (New Settings) • Revert to Saved Settings The settings are saved when you tap OK. The settings are saved when you tap ‘Yes’. When open, Decoding Properties acts as a simple barcode test tool that provides the Data decoded and the Data Type of the barcode scanned.
USE AND FUNCTIONING 4.6.2 4 Buttons From the Start menu, tap Settings > Personal > Buttons. On the Program Buttons tab, customize the program hardware buttons to launch your most used applications. Under ‘Select a button’, tap the button you want to assign a program to, and then select a program from ‘Assign a program’. To configure the way the up/down control repeats, use the Up/Down Control applet (Start > Settings > Personal > Buttons and then tap Up/Down Control).
1 LYNX™ 4 4.6.3 DL Buttons In Windows Embedded Handheld devices, - buttons (excluding F5) are assigned by Windows to default applications. F5 is commonly used by applications to refresh the few, but is not explicitly controlled by default. To disable an assigned function, tap Start > Settings > System > DL Buttons to display the DL Buttons window: Select the button you want to disable. Select the function ‘None’ and the tap OK.
USE AND FUNCTIONING 4 To add the button, tap ‘New’ and then press the button you wish to add: To assign a new function to the button, select the desired function and then tap ‘OK’: To restore the old settings, do a clean boot.
1 LYNX™ 4 4.6.4 Triggers Triggers are special customizable buttons that are mapped by default by DL Buttons. Also, they can be set as wakeup buttons: AVAILABLE FUNCTIONS TRIGGERS Bar Code Camera Shutter Bar Code/ Camera Shutter ∗ Activates the scanner even if the camera app is running. Takes a picture if the Camera app is running but will do nothing if it isn't running. Activates the scanner if the Camera app is not running but will take a picture if the Camera app is running.
USE AND FUNCTIONING 4.6.5 4 Application Switcher The application switcher provides the same functionality as the standard Windows® Alt+Tab function. This allows the user to switch between the various open applications. The application switcher can be activated via an assigned shortcut key specified in the “DL Buttons” tab (refer to par. 4.6.3). When the assigned button is pressed, the dialog shown below will be displayed: The key can be used to close the Application Switcher.
1 LYNX™ 4 4.6.6 Wireless Communications The Wireless Manager application is a sort of 'Control Panel' for wireless connections. From here it is possible to turn on or off Bluetooth® and radio modules. Open the Wireless Manager by tapping Start > Settings > Connections > Wireless Manager, or by tapping the connectivity icon on the taskbar and then tapping the "Wireless Manager" hypertext link (see par.4.5.2).
USE AND FUNCTIONING 4 Summit Client Utility (SCU) Wireless networking has a customized control, Summit Client Utility (SCU).
4 1. 1 LYNX™ To create a new profile, tap the "Profile" tab: Information about the wireless network can be entered directly in the profile tab or by pressing “Scan” when the desired network SSID is in range. 2.
USE AND FUNCTIONING 4 3. Tap the "Configure" button 4. Follow the on-screen instructions to configure security parameters for your network. For more detailed settings specific to your installation please contact your wireless network administrator. 5. When finished, tap “Commit” to save your settings. Return to the “Main” tab, if you have not previously selected “Commit” you will be prompted to save your changes.
4 1 LYNX™ At the “Main” tab select the profile you just created. If you used the “scan” button the desired profile will have the same name as the SSID. Use the “Status” tab to check connectivity to the network. More detailed information about the applet for radio configuration can be found at http://www.summitdata.com/Documents/summit_users_guide_3_03.html.
USE AND FUNCTIONING 4 Locating the IMEI Number on the Lynx To find the IMEI number on the Lynx 3G/4G HSPA+ units, do the following steps: 1. Install a SIM card (see par.1.5) 2. From the desktop of the unit open the Start Menu > Settings > Connections > Wireless Manager. 3. Make sure the Phone is set to ON. If it’s off then tap on Phone to turn it on.
4 1 LYNX™ 4. Tap on Menu at the bottom of the screen and choose Phone Settings. 5. Tap the right or left arrow until Info displays in the center of the title bar. The IMEI number should now be showing on the screen.
USE AND FUNCTIONING 4.6.7 4 Stylus Calibration You might need to recalibrate the touch screen (i.e. when you attempt to select one item with the stylus, another item is erroneously selected). To recalibrate the touch screen, complete the following steps: 1. Select Start > Settings > System > Screen to open the Screen Settings. 2. Tap Align Screen to open the Calibration screen shown in the figure below: 3. Carefully press and briefly hold stylus on the center of the target.
4 1 LYNX™ Startup Stylus Calibration When clean booting the terminal, a Welcome Wizard (with Stylus Calibration) comes up if valid calibration settings are not available.
USE AND FUNCTIONING 4.6.8 4 Audio Settings There are two applets that control volume: Audio and Volume & Sounds. Audio From the Start Menu, tap Settings > System > Audio: The audio control panel can be used to independently set the playback or recording volume for different types of audio inputs and outputs, such as a headset, powered mobile dock, or the internal speakers and microphone.
1 LYNX™ 4 Sounds & Notifications From the Start Menu, tap Settings > Sounds & Notifications: The Sounds & Notifications applet configures audio features of all speakers and headphones: Sounds Tab 74 Notifications Tab
USE AND FUNCTIONING 4 You can also set the volume of a paired Bluetooth®headset. Tap: Start > Settings > System > Bluetooth Manager, select the Connections tab and then select the headset pairing in the Paired Devices list.
1 LYNX™ 4 4.7 CONNECTING TO OTHER COMPUTERS To connect the Lynx to another device (i.e. Host PC) which run Windows, several programs are available. These programs require specific electrical connections in order to function properly. 4.7.1 Windows Mobile® Device Center The desktop application Windows Mobile® Device Center gives you the ability to synchronize information between a desktop computer and your Lynx.
USE AND FUNCTIONING 4.7.2 4 Bluetooth® Manager Device Setup Using the Lynx to connect to another device To create a Bluetooth® pairing between your device and another device that has Bluetooth® capabilities, ensure that the two devices are turned on, discoverable, and within close range. 1. Open the Bluetooth® control panel by tapping Start > Settings > System > Bluetooth Manager: 2.
4 3. 1 LYNX™ Once searching is complete, Bluetooth® devices will be displayed in the Discovery tab. You can set up a connection to a device in the list by selecting the device and then tapping the 'Connect' button: To create a pairing: 1. Select a service: 2. Configure any encryption, authentication, or virtual port options required by the service selected.
USE AND FUNCTIONING Icon 4 Service Dialup Networking Printer Object Push (OPP) or Object Exchange (OBEX) ActiveSync Human Interface Device (HID) - Keyboard Serial Personal Area Network (PAN) Modem Headset Handsfree Virtual Port allows you to specify the incoming port, which is used to communicate serially with an incoming device just as if it were a physical COM port. This option is available only if you have selected a Printer or Serial service.
4 1 LYNX™ You can also select Encrypt or Authenticate from the Bluetooth® control panel to apply or modify those settings. 1. To require Authentication, check the checkbox, then tap OK. 2. If required, the Authentication Request dialog will then open, requesting that you enter a PIN. Use the Input Panel or the keyboard to type the PIN. 3. Tap OK to complete.
USE AND FUNCTIONING 4 The dialog will also appear when an Authentication request is received from another device. Once you have set up a Pairing, you can view the settings by double-tapping its name in the Connections tab. Tap the arrow to change the Virtual Port, or Delete to remove the device pairing. Tap Sync to initiate a Sync (available only if the service is an ActiveSync connection).
4 1 LYNX™ Using your device to connect to the Lynx Before turning on Bluetooth® ensure that the two devices are within close range and that both Bluetooth-enabled devices are discoverable. 1. Tap Start > Settings > System > Bluetooth Manager to open the Bluetooth® control panel. 2. Tap Settings. The Settings tab allows you to enable or disable the Bluetooth® radio and specify settings for Incoming Connections.
USE AND FUNCTIONING 4 3. Select or clear the “Enable Bluetooth Radio” check box. If you’re going to be attaching a serial device (i.e. a scanner) to the Lynx, use the Port control to select a virtual COM port to use for the connection. 4. Tap ‘Find Me’ if you want to make the Lynx visible to other Bluetooth® devices for 60 seconds, allowing them to set up a connection.
4 1 LYNX™ By default, Bluetooth® is turned off. If you turn it on, and then turn off your device, Bluetooth® also turns off. When you turn on your device again, Bluetooth® turns on automatically.
USE AND FUNCTIONING 4.8 4 DATALOGIC FIRMWARE UTILITY The Datalogic devices are equipped with a field upgradeable firmware mechanism. Firmware updates are available on the Datalogic website: http://www.datalogic.com/eng/support-services/automatic-datacapture/downloads/software-utilities-sw-2.html. After you have downloaded the desired update, there are several ways you can update the firmware on your device. − Use Wavelink Avalanche™ if you have multiple Datalogic devices to update.
1 LYNX™ 4 4.8.2 Installing DFU on the Host PC The Datalogic Firmware Utility (DFU) provides administrators with a field upgrade mechanism. You must have Microsoft® ActiveSync (for Windows XP devices) or Windows Mobile® Device Center (for Windows 7 and Vista devices) already loaded and running on the host PC to use DFU. Refer to par. 4.7.1 for more information about Windows Mobile® Device Center. Prior to installing, you must remove any previous versions of DFU installed on the host PC.
USE AND FUNCTIONING 4.8.3 4 Updating the Firmware After copying the firmware image to the host PC (see par. 4.10.1) and installing DFU (see par. 4.8.2), you can upgrade the firmware on your Datalogic device. The following steps require that you have already established an ActiveSync or Windows Mobile® Device Center connection between the host computer and the Datalogic device. NOTE 1. Go to Start > Programs > Datalogic > DFU > Datalogic Firmware Utility. 2.
1 LYNX™ 4 4.9 DATALOGIC CONFIGURATION UTILITY Datalogic Configuration Utility (DCU) is a Datalogic Windows-based utility tool allowing the uploading, modifying and downloading of the configuration of a Datalogic device. Configuration settings include Scanner, Control Panel, and Datalogic Desktop Utility (DDU). The DCU installer is downloadable from the Datalogic website (http://www.datalogic.com/eng/support-services/automatic-datacapture/downloads/software-utilities-sw-2.html).
USE AND FUNCTIONING 4 4.10 RADIO POWER MANAGEMENT The Lynx's power management allows the user to keep device features powered while the device is off. The features managed by this feature are: Cellular Data/Voice and GPS. NOTE The Wi-Fi driver has been measured to consume about 50 µA when left powered. As a result, Wi-Fi will always be left powered during suspend. This has the positive effect of substantially reducing the time required for Wi-Fi to fully resume when the device is powered back on.
4 1 LYNX™ The term "device off" here refers to a condition where the display is off and the device appears unpowered. The device CPU may in fact be powered on. In this condition the power consumption can be relevant and battery can be completely discharged in several hours.
USE AND FUNCTIONING 4 4.11 DATALOGIC DESKTOP UTILITY ® Datalogic Desktop Utility (DDU) allows administrators to configure Windows CE and Embedded Handheld devices to control individual user access. This includes the ability to: • • • • • Prevent users from changing your device OS settings. Use the Application Selector to replace the desktop with a selection of authorized applications. Restrict user access in Internet Explorer. Set up configuration and customized error recovery mechanisms.
1 LYNX™ 4 4.11.1 Administrative Options (Admin tab) When you open the DDU control panel, the “Admin” tab appears. COMMAND DESCRIPTION Enable Datalogic Desktop Select/tap this checkbox to activate the DDU functions such as Windows Access Restrictions and Application Selector. Enter Password Enter a password in the text box. This allows the user to specify a password when this utility is launched. By default the password is “1234”. A password can consist of all standard keyboard characters.
USE AND FUNCTIONING 4 Setting a Password To set a password: 1. Enter a password in the field. This allows the user to specify a password when this utility is launched. By default the password is “1234”. Be sure to record the Password for future reference. NOTE 2. 3. 4. Re-enter the password in the second field. Select/tap “Set Password” to enable the password. Select/tap “OK” to close the “Set Password Confirmation” dialog.
4 1 LYNX™ Removing a Password To remove a password: 1. 2. Delete the contents of in both “Password” fields. Select/tap “Set Password”. Password Request Dialog Box Once the password is set, the next time you open the “Datalogic Desktop Utility”, the DDU Password dialog box opens. This dialog box will only open if a password was defined. 1. Type in your password using either the keypad on the unit, or using the stylus on the soft input panel (SIP).
USE AND FUNCTIONING 4.11.2 4 Locked Web Browser Options (LockedWeb tab) Tap the LockedWeb tab to access the Locked Web Browser Configuration. Locked Web Browser is disabled by default. To enable, go to “Advanced settings” on the next page for more information. NOTE For additional information about Locked Web Browser commands and metatags, see section 4.14, “Locked Web Browser”. Error Page Redirection Use the Error Redirection option to provide customized recovery from common errors.
1 LYNX™ 4 Error Redirection options Error Type The “Error Type” pull-down list displays available Error Types: (400) Invalid Syntax, (403) Request Forbidden, (404) Object Not Found, (406) No Response Format, (410) Page Doesn't Exist, (500) Internal Server Error, (501) Server Can't Do That, Generic Error, Network Disconnected Error Page Edit this textbox to associate a website or html file with the specified error. Other options Full Screen Set the web browser in full screen mode.
USE AND FUNCTIONING 4 Advanced settings General Tab Context Menu 97
1 LYNX™ 4 Advanced Locked Web Browser options General Enable Locked When checked, enables the Locked Web Browser when Internet Web Browser Explorer is launched. Disable Cache Prevents the browser from loading the local intranet page from cache instead of navigating to the “Network Disconnected” error redirection page. Allowed Website Enables a “white list,” which restricts browsing only to files and URLs in the Allowed Website list (accessed by the “…” button).
USE AND FUNCTIONING 4 Context Menu Enable Context Menu Enables the context menu accessed by a touch screen press in the Locked Web Browser. Refresh Adds a “Refresh” item to the Locked Web Browser context menu. Selecting the “Refresh” item refreshes the web page. Stop Adds a “Stop” item to the Locked Web Browser context menu. Selecting during navigation stops the downloading of a page. Current URL Adds a “Current URL” item to the Locked Web Browser context menu.
1 LYNX™ 4 4.11.3 Status Icons Options (Status Tab) Tap the “Status” tab to access the Status Icons option. You can configure the view of some status icons that are used in “WebAppLock” and in “Application Selector” to display the status of: wi-fi radio, battery and GSM. Status Icons Options Set Status Icon Defaults Restores the status icons’ factory settings. Icon Size Sets the status icons’ size. Icon Location Selects the preferred location for each status icon.
USE AND FUNCTIONING 4.11.4 4 Windows Controls Select/tap the “Win” (Windows Controls) tab to access the Windows Controls option. Use Windows controls to allow or restrict access to Windows system functions. You can disable normal Windows functions such as the taskbar, leaving nothing but a blank workspace. This allows applications to be run in full screen mode and prevents users from accidental or unauthorized use of the taskbar, Internet Explorer, and any other resident applications.
1 LYNX™ 4 Windows Controls Taskbar Enabled Select/tap “Taskbar Enabled” to specify whether the taskbar is accessible. AutoSIP Enabled Enables the AutoSIP Windows feature. Scroll Bars Enabled This control only take effects in WebAppLock. When checked, displays horizontal and vertical scroll bars to help view large web pages which do not fit the screen. When unckecked, those scrolls will not be present.
USE AND FUNCTIONING 4.11.5 4 AppSelector Options (AppSelect tab) Tap the Application Selector (“AppSelect” Tab) to edit, add, or delete applications for the application selector. Application Selector Options Enable Application Selector Select/tap “Enable Application Selector” to enable/disable the application selector. When enabled, the Application Selector replaces the desktop and allows only authorized use of applications. Show status icons Enable or disable the status icons view (see par. 4.12.
1 LYNX™ 4 Application Selector Commands New Select/tap “New” to create a new application entry. Edit Select/tap “Edit” to edit the selected entry. Del Select/tap “Del” to delete the selected entry. Up/Down Select/tap “Up/Down” to move an entry up or down in the Authorized Applications list.
USE AND FUNCTIONING 4 Add Applications The “Add Application” dialog opens when you tap either “New” or “Edit”. From the “Add Application” dialog the administrator can configure and/or add/change a new application entry in the list. Applications with the “Run Application at Startup” option enabled will start automatically when the Application Selector starts up. COMMAND DESCRIPTION Application Title Type the name of the application in this textbox in the way you wish it to appear for the user.
1 LYNX™ 4 COMMAND DESCRIPTION Icon File Displays the path/link to the desired icon file. Browse to browse for the desired icon file. The Select/tap results of this search are placed in the “Icon File” textbox. Run Application at Startup Select/tap this box to force this application to auto start when the Application Selector starts up. Applications will be started in the order listed in the authorized application list. Delay Enter a delay duration in seconds in the combo box.
USE AND FUNCTIONING 4 4.12 APPSELECTOR (APPLICATION SELECTOR) The Application Selector is an application that allows a device to run in kiosk mode. The administrator can choose for the user to have access to the desktop or not. The Application Selector can replace the desktop and limit the user to the specified list of applications. By default, the Application Selector comes with the LockedWeb preset. Application Selector The administrator can customize this list as shown in chapter 4.12.5.
1 LYNX™ 4 4.13 LOCKED WEB BROWSER The Locked Web Browser is a web browser helper object for Internet Explorer. It allows an administrator to define a restricted internet usage environment. Once in the restricted environment, a password is required to exit. This means users can only access web applications and websites set by the administrator. Configuration is set up through the DDU control panel. See section 4.12.2 for more information.
USE AND FUNCTIONING 4 For firmware versions 1.60 and newer, the following command line arguments are supported: - /E optional parameter which allows for Exit without entering a password - @URL optional parameter which specifies a URL to use as a home page. - /C optional parameter which disables the ctrl keys (including the one to exit).
1 LYNX™ 4 4.13.1 Locked Web Browser Special Meta-tags General Metatag Comments A metatag is a special HTML tag that stores information about a Web page but does not display in a Web browser. For example, metatags provide information such as the program used to create the page, a description of the page, and keywords relevant to the page. As per the HTML specification, all metatags must be contained within a
… tag set.USE AND FUNCTIONING 4 GetSerialNumber Metatag DL_GetSerialNumber – Obtains the device serial number and sends it as an argument to a customer’s javascript function. Content – name of function to pass serial number to. Example: When a page with this metatag is loaded, the content should be a javascript function that receives one parameter, the serial number. An example would be function CustomerFunction(SerialNumber).
1 LYNX™ 4 Decoding Metatags: Each decoding metatag has a possible content of “Enable” or “Disable”. The settings are valid for the entire page (enables/disables each symbology).
USE AND FUNCTIONING 4 Key press Metatags The key press metatags can be used to call JavaScript functions. They have the name structure: “DL_Key_xxx” where xxx is the VKey code. Example: Assigning a key press via a DL_Key metatag overrides its use on the page. For instance, when entering data in a text box a character assigned as a DL_Key would not be entered in the text box. Instead, the javascript action would occur.
1 LYNX™ 4 4.14 AUTOSTART The AutoStart program provides three functions: Allows you to create a list of applications (with optional command line arguments) to run automatically prior to loading CAB files. - Automatically reinstalls specified CAB files when the Lynx is cold booted. - Allows you to create a list of applications (with optional command line arguments) to run automatically after loading CAB files.
USE AND FUNCTIONING 4.14.2 4 How AutoStart Uses Wceload NOTE If you intend to create highly interactive installers, you should either install the CABs manually or review the section on “Interactive CAB Install” in this chapter.. In certain environments, CAB files will be deleted after execution. To prevent the CAB file from being deleted, write protect the file before copying the file onto the device. CAUTION CAB files are installed by AutoStart using the Wceload.exe application.
1 LYNX™ 4 4.14.3 − Interactive CAB Install If the CAB installer requires user interaction that must be performed during the AutoStart CAB installation process, you can specify a special file name to disable the silent mode installation. If this mode is specified, the CAB file will be installed with Wceload without any command line arguments specified. An example of what AutoStart would execute is: \Windows\Wceload.
USE AND FUNCTIONING 4 The following table breaks down the sample Autostart.ini line: Autostart option(s) - Full path to executable \windows\pword.exe Command line arguments \file.doc Spaces must be placed between each component of the line in the Autostart.ini. If the executable path is in a folder that contains spaces in the name, quotes are required to distinguish what the actual executable name is. The following is an example of this: “\Program Files\ScannerApp.
1 LYNX™ 4 AutoStart Options The table below shows options you can use when writing a line in the Autostart.ini file. Description Character Comment: This line will not be ‘#’ OR ‘ ‘ (space) executed. Comments This may only be used as the first character of the line. If the comment option is specified in the options elsewhere, it is ignored. Do not wait on line completion: This will cause the line to ‘-’ execute and immediately move onto the next line.
USE AND FUNCTIONING 4 Combining Options Autostart options can be combined together as shown in the following sample: ?- \Windows\Pword.exe This line would: − Request confirmation before executing the line. The next line would not be processed before the confirmation is answered. − Run the next line without waiting on the current line to complete execution. Query Option The query option is intended for use when debugging the autostart.ini.
1 LYNX™ 4 The fields may be broken up into multiple lines (as shown in the example) due to limited space in the dialog. NOTE AutoStart Query Options Parentheses are used to surround the given field and make it very clear what the value of the field is. The following table describes the results of each choice: Button Action Yes The current line will execute. No The current line will not execute. AutoStart will continue parsing the Autostart.ini.
USE AND FUNCTIONING 4 Autostart.ini Samples The next table is a collection of sample Autostart.ini lines: Line Description This will confirm the execution of ? \windows\wceload.exe “\My \Windows\wceload.exe with specified argument Documents\Sample.cab” “\My Documents\Sample.cab” \Program Files\App.exe (invalid) This will execute \Program with the argument Files\App.exe. \Program Files\App.exe /run (invalid) This will execute \Program with the argument Files\App.exe /run. “\Program Files\App.
1 LYNX™ 5 5 TECHNICAL FEATURES 5.1 TECHNICAL DATA PHYSICAL CHARACTERISTICS DIMENSIONS (LXWXH) WEIGHT With Standard Battery: 14.4 x 6.8 x 2.7 cm / 5.6 x 2.6 x 1.0 in With Hi-Capacity Battery: 14.4 x 6.8 x 3.3 cm / 5.6 x 2.6 x 1.3 in With Standard Battery: 270.0 g / 9.5 oz With Hi-Capacity Battery: 300.0 g / 10.6 oz AUDIO Main (rear) speaker Receiver (front) speaker LEDS Three LEDs Decoding Status/ Keyboard Status/ Charging Status DISPLAY TFT-LCD color display QVGA: 320 x 240 pixels; 2.
TECHNICAL FEATURES 5 SYSTEM OPERATING SYSTEM Microsoft Windows Embedded Handheld 6.5 with Mobile Tools: Text, Messaging, Word Mobile, Excel Mobile, PowerPoint Mobile, One Note Mobile and Internet Explorer Mobile 6.0 MICROPROCESSOR XScale™ PXA310 @ 806 MHz SYSTEM RAM MEMORY 256 MB SYSTEM FLASH MEMORY 512 MB Removable battery pack with rechargeable Li-ion batteries; 3.7 V 1800/3600 mAh (6.6/13.3 Watt hours). Micro-USB power adapter for direct charge and power adapter.
1 LYNX™ 5 COMMUNICATIONS Micro-USB connector: USB 1.1 Client and USB 1.1 Host HandyLink™ connector: integrated RS-232 up to 115.2 Kbps, USB 1.1 Client, USB 1.1 Host Ethernet: via single dock (external module) or multiple cradle GSM/GPRS/EDGE: Quad band, 850/900/1800/1900 MHz INTERFACES WIDE AREA NETWORK (WAN) UMTS/HSPA+: PH8-P: Five band, 800/850/900/1900/2100 MHz for voice and data communication; SIM socket under the battery LOCAL AREA NETWORK (LAN) Summit IEEE 802.
TECHNICAL FEATURES 5 READING OPTIONS LASER CHARACTERISTICS SCANNING RATE 104 ± 12 scan/sec OPTICAL RESOLUTION 0.10 mm / 4 mils DEPTH OF FIELD See reading diagram (par. 5.2) SKEW ANGLE ± 50° PITCH ANGLE ± 65° AIMING LASER VLD, wavelength 630~670 nm BAR CODES GS1-DataBar family, EAN/UPC, Code 39, 2/5 Codes, Codabar, Code 128, GS1-128, MSI, Code 93. LASER CLASSIFICATION VLD - Class 2 IEC/EN60825-1; Compliant with 21 CFR 1040.10 except for deviations pursuant to laser notice No.
1 LYNX™ 5 5.2 READING DIAGRAMS Lynx SE950-DL Symbol Density/ Bar Code Type/ W-N Ratio 4.0 mil Code 39; 2.5:1 5.0 mil Code 39; 2.5:1 7.5 mil Code 39; 2.5:1 10 mil Code 39; 2.5:1 13 mil 100% UPC 15 mil Code 39; 2.5:1 20 mil Code 39; 2.2:1 40 mil Code 39; 2.2:1 55 mil Code 39; 2.
TECHNICAL FEATURES 5 LYNX SE4500-DL Symbol Density/ Bar Code Type Far Guaranted Working Ranges 3.0 mil Code 39 3,1 in 7,9 cm 5.0 mil Code 39 6,1 in 15,52 cm 5.0 mil PDF417 3,3 in 8,41 cm 6.67 mil PDF417 5,6 in 14,25 cm 7.5 mil Code 39 8,2 in 20,85 cm 10 mil PDF417 7,4 in 18,82 cm 13 mil UPC-A 10,1 in 25,68 cm 15 mil PDF417 9,9 in 25,17 cm 15 mil Data Matrix in n.a. cm n.a.
1 LYNX™ 6 6 TEST CODES High Density Codes 0.
TEST CODES 6 Medium Density Codes 0.
1 LYNX™ 6 Low Density Codes 0.
TEST CODES 6 2D Codes Datamatrix ECC200 Example Inverse Datamatrix ECC200 Example 131
6 SAFETY REGULATIONS Read this manual carefully before performing any type of connection to the Lynx PDA. NOTE The user is responsible for any damages caused by incorrect use of the equipment or by inobservance of the indication supplied in this manual. GENERAL SAFETY RULES − Use only the components supplied by the manufacturer for the specific Lynx being used. − Do not attempt to disassemble the Lynx PDA, as it does not contain parts that can be repaired by the user.
LASER SAFETY The laser light is visible to the human eye and is emitted from the window indicated in the figure. This information applies to both laser models and the Lynx Imager Aiming System.
6 I D La luce laser è visibile all'occhio umano e viene emessa dalla finestra indicata nella figura. Die Laserstrahlung ist für das menschliche Auge sichtbar und wird am Strahlaustrittsfenster ausgesendet (siehe Bild). Le rayon laser est visible à l'oeil nu et il est émis par la fenêtre désignée sur l'illustration dans la figure. La luz láser es visible al ojo humano y es emitida por la ventana indicada en la figura.
ENGLISH The following information is provided to comply with the rules imposed by international authorities and refers to the correct use of your PDA. STANDARD LASER SAFETY REGULATIONS This product conforms to the applicable requirements of both CDRH 21 CFR 1040 Subchapter J and IEC 60825-1:2007 at the date of manufacture. For installation, use and maintenance, it is not necessary to open the device. CAUTION CAUTION Do not attempt to open or otherwise service any components in the optics cavity.
6 Non tentare di accedere allo scomparto contenete i componenti ottici o di farne la manutenzione. ATTENZIONE ATTENZIONE L’apertura dello scomparto, o la manutenzione di qualsiasi parte ottica da parte di personale non autorizzato, potrebbe violare le norme della sicurezza. Il sistema ottico può essere riparato solamente alla fabbrica. L'utilizzo di procedure o regolazioni differenti da quelle descritte nella documentazione può provocare un'esposizione pericolosa a luce laser visibile.
ACHTUNG ACHTUNG Unter keinen Umständen darf versucht werden, die Komponenten im Optikhohlraum zu öffnen oder auf irgendwelche andere Weise zu warten. Das Öffnen bzw. Warten der Komponenten im Optikhohlraum durch unbefugtes Personal verstößt gegen die Laser-Sicherheitsbestimmungen. Das Optiksystem darf nur werkseitig repariert werden. Jegliche Änderungen am Gerät sowie Vorgehensweisen, die nicht in dieser Betriebsanleitung beschrieben werden, können ein gefährliches Laserlicht verursachen.
6 L'utilisation de procédures ou réglages différents de ceux donnés ici peut entraîner une dangereuse exposition à lumière laser visible. ATTENTION Le produit utilise une diode laser. Aucun dommage aux yeux humains n’a été constaté à la suite d’une exposition au rayon laser. Eviter de regarder fixement le rayon, comme toute autre source lumineuse intense telle que le soleil. Eviter aussi de diriger le rayon vers les yeux d’un observateur, même à travers des surfaces réfléchissantes (miroirs, par exemple).
El aparato utiliza un diodo láser a baja potencia. No son notorios daños a los ojos humanos a consecuencia de una exposición de corta duración. Eviten de mirar fijo el rayo láser así como evitarían cualquiera otra fuente de luminosidad intensa, por ejemplo el sol. Además, eviten de dirigir el rayo láser hacia los ojos de un observador, también a través de superficies reflectantes como los espejos. ATENCIÓN El uso de sistemas ópticos con el escáner aumentará el riesgo de daños oculares.
6 RADIO COMPLIANCE In radio systems configured with PDAs and access points, the frequencies to be used must be allowed by the spectrum authorities of the specific country in which the installation takes place. Be absolutely sure that the system frequencies are correctly set to be compliant with the spectrum requirements of the country. The Radio modules used in this product automatically adapt to the frequencies set by the system and do not require any parameter settings.
Information for the User ENGLISH Contact the competent authority responsible for the management of radio frequency devices of your country to verify any possible restrictions or licenses required. Refer to the web site http://ec.europa.eu/enterprise/sectors/rtte/documents/contactspoints/spectr/ for further information. ITALIANO Contatta l'autorità competente per la gestione degli apparati a radio frequenza del tuo paese, per verificare eventuali restrizioni o licenze.
6 FCC COMPLIANCE FCC Regulations • This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. • This device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
RF EXPOSURE INFORMATION (SAR) This model device meets the government’s requirements for exposure to radio waves. This device is designed and manufactured not to exceed the emission limits for exposure to radio frequency (RF) energy set by the Federal Communications Commission of the U.S. Government. The exposure standard for wireless devices employs a unit of measurement known as the Specific Absorption Rate, or SAR. The SAR limit set by the FCC is 1.6W/kg.
6 INDUSTRY CANADA COMPLIANCE Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
SAR COMPLIANCE 1. For the used worst case positions, the portable device Lynx from Datalogic (FCC ID: U4G0070 and U4G0073) is in compliance with the IC RSS 102 Issue 4 [RSS 102] and Federal Communications Commission (FCC) Guidelines [OET 65] for uncontrolled exposure. SAR assessment in body worn was conducted with a distance of 15 mm between the housing of the handheld and the flat phantom. 2.
6 WEEE COMPLIANCE Informazione degli utenti ai sensi della Direttiva Europea 2002/96/EC L’apparecchiatura che riporta il simbolo del bidone barrato deve essere smaltita, alla fine della sua vita utile, separatamente dai rifiuti urbani.
Information aux utilisateurs concernant la Directive Européenne 2002/96/EC Au terme de sa vie utile, le produit qui porte le symbole d'un caisson à ordures barré ne doit pas être éliminé avec les déchets urbains.
GLOSSARY Access Point A device that provides transparent access between Ethernet wired networks and IEEE 802.11 interoperable radio-equipped mobile units. Hand-held mobile computers, PDAs or other devices equipped with radio cards, communicate with wired networks using Access Points (AP). The mobile unit (PDA) may roam among the APs in the same subnet while maintaining a continuous, seamless connection to the wired network.
Decode To recognize a bar code symbology (e.g., Codabar, Code 128, Code 3 of 9, UPC/EAN, etc.) and convert the content of the bar code scanned from a visual pattern into electronic data. Depth of Field (DOF) The portion of a scene that appears acceptably sharp in the image. Although a lens can precisely focus at only one distance, the decrease in sharpness is gradual on each side of the focused distance, so that within the DOF, the unsharpness is imperceptible under normal viewing conditions.
HSPA+ HSPA+, or Evolved High-Speed Packet Access, is a technical standard for wireless, broadband telecommunication. HSPA+ enhances the widely used WCDMA (UMTS) based 3G networks with higher speeds for the end user. Host A computer that serves other mobile computers in a network, providing services such as network control, database access, special programs, supervisory programs, or programming languages. IEEE 802.
RAM Random Access memory. Data in RAM can be accessed in random order, and quickly written and read. RF Radio Frequency. RTC Real Time Clock. USB Universal Serial Bus. Type of serial bus that allows peripheral devices (disks, modems, printers, digitizers, data gloves, etc.) to be easily connected to a computer. A “plug-and-play” interface, it allows a device to be added without an adapter card and without rebooting the computer (the latter is known as hot-plugging).
INDEX Glossary; 148 A Accessories; 11 Audio Settings; 73 Autostart; 114 Available Models; 2 B Batteries and Maintenance; 13 Bluetooth® Manager Device Setup; 77 Buttons; 59 C Charging the Batteries; 13 Cleaning the PDA; 19 Connecting to other Computers; 76 Connections; 20 Connection to USB peripherals; 22 RS232 Connection; 25 USB Connection; 20 WLAN Connection; 27 WPAN Connections; 29 D Data Capture; 37 Imager Data Capture; 40 Laser Data Capture; 38 Data Capture Configuration; 50 Datalogic Configuration Util
T Taskbar; 48 Technical Data; 122 Technical Features; 122 Test Codes; 128 U Using the Stylus; 35 153 W WEEE Compliance; 146 Windows Embedded Handheld Welcome Wizard; 36 Windows Mobile® Device Center; 76 Wireless and Radio Frequencies Warnings; 32 Wireless Communication; 64 WWAN Connection; 30
13 DECLARATION OF CONFORMITY Datalogic ADC S.r.l. Via S. Vitalino 13 40012 - Lippo di Calderara Bologna - Italy dichiara che declares that the déclare que le bescheinigt ,daß das Gerät declare que el LYNX modelli con funzionalità radio 802.11a/b/g+BT models with 802.11a/b/g+BT radio feature modèles avec 802.11a/b/g+BT radio intégrés modelle mit 802.11a/b/g+BT radio-funktionalität modelos con funcionalidad radio 802.
ETSI EN 301 489-17 V2.1.1: 2009 ELECTROMAGNETIC COMPATIBILITY AND RADIO SPECTRUM MATTERS (ERM); ELECTROMAGNETIC COMPATIBILITY (EMC) STANDARD FOR RADIO EQUIPMENT; PART 17: SPECIFIC CONDITIONS FOR 2,4 GHZ WIDEBAND TRANSMISSION SYSTEMS, 5 GHZ HIGH PERFORMANCE RLAN EQUIPMENT AND 5,8 GHZ BROADBAND DATA TRANSMITTING SYSTEMS ETSI EN 300 328 V1.7.
13 DECLARATION OF CONFORMITY Datalogic ADC S.r.l. Via S. Vitalino 13 40012 - Lippo di Calderara Bologna - Italy dichiara che declares that the déclare que le bescheinigt ,daß das Gerät declare que el LYNX modelli con funzionalità radio WWAN+802.11a/b/g+BT models with WWAN+802.11a/b/g+BT radio feature modèles avec WWAN+802.11a/b/g+BT radio intégrés modelle mit WWAN+802.11a/b/g+BT radio-funktionalität modelos con funcionalidad radio WWAN+802.
ETSI EN 301 489-3 V1.4.1: 2002 ELECTROMAGNETIC MATTERS (ERM); COMPATIBILITY AND RADIO SPECTRUM ELECTROMAGNETIC COMPATIBILITY (EMC) STANDARD FOR RADIO EQUIPMENT AND SERVICES; PART3: SPECIFIC CONDITIONS FOR SHORT-RANGE DEVICES (SRD) OPERATING ON FREQUENCIES BETWEEN 9KHZ AND 40GHZ ETSI EN 301 489-7 V1.3.
EN 60950-1:2006 AMENDMENT A11:2009 AMENDMENT A1: 2010 AMENDMENT A12: 2011 INFORMATION TECHNOLOGY EQUIPMENT - SAFETY PART 1 : GENERAL REQUIREMENTS IEC60950-1:2005 AMENDMENTA1: 2009 INFORMATION TECHNOLOGY EQUIPMENT - SAFETY PART 1 : GENERAL REQUIREMENTS EN50332-2: 2003 SOUND SYSTEM EQUIPMENT - HEADPHONES AND EARPHONES ASSOCIATED WITH PORTABLE AUDIO EQUIPMENT - MAXIMUM SOUND PRESSURE LEVEL MEASUREMENT METHODOLOGY AND LIMIT CONSIDERATIONS - PART 2: MATCHING OF SETS WITH HEADPHONES IF EITHER OR BOTH ARE OFF
Lynx™ Personal Digital Assistant (PDA) www.datalogic.com © 2012-2014 Datalogic ADC S.r.l. All rights reserved. Datalogic and the Datalogic logo are registered trademarks of Datalogic S.p.A. In many countries, including the U.S.A. and the E.U. Datalogic ADC S.r.l. Via S.
