User Guide

Matrix 220™
QUICK REFERENCE GUIDE
Download the Matrix 220 Product Reference
Guide by reading the QR code here or see
the paragraph below.
SUPPORT THROUGH THE WEBSITE
Datalogic provides several services as well as technical support through
its website. Log on to
www.datalogic.com.
For quick access, from the home page click on the search icon , and type
in the name of the product you’re looking for. This allows you access to
download Data Sheets, Manuals, Software & Utilities, and Drawings.
Hover over the Support & Service menu for access to Services and
Technical Support.
INSTALLATION PROCEDURE
1. Physically mount the Matrix 220 reader.
2. Make the necessary electrical connections.
3. Configure the reader using the X-PRESS interface (AIM, SETUP,
LEARN and TEST for simple configuration) or the DL.CODE
software configuration program (complete configuration).
HMI X-PRESS™ INTERFACE
In normal operating mode the colors and meaning of the five LEDs are
illustrated in the following table:
READY (green)
indicates the device is ready to operate.
GOOD (green)
confirms successful reading.
TRIGGER (yellow)
indicates the status of the reading phase.
COM (yellow)
indicates active communication on main serial
port.
STATUS (red)
indicates a NO READ result.
During the reader startup (reset or restart phase), all the LEDs blink for
one second.
The single push button gives immediate access to the following relevant
functions:
Test Mode with bar graph visualization to check static
reading performance.
Aim turns on the LED pointers to aim the reader at the target.
The target should be centered horizontally and vertically
with respect to the aiming squares.
Setup to self-optimize and auto-configure photometry
parameters.
Learn to self-detect and auto-configure for reading an
unknown barcode (by type and length). Only one symbology
type can be saved using this method. Performing Autolearn
on a second symbology will overwrite the first one.
Matrix 220™
General View
Matrix 220 Power, COM, I/O Matrix 220 PoE COM, Trigger Matrix 220 Ethernet
11
12
13
14
Lens
LED Aiming System
Red Spot (No Read)
Green Spot (Good Read)
M12 17-pin Power, COM, and I/O Connector Pinout
Pin
Name
Function
1
Vdc
Power supply input voltage +
2
GND
Power supply input voltage -
Connector
Case
CHASSIS
Connector case provides electrical
connection to the chassis
6
I1A
External Trigger A (polarity insensitive)
5
I1B
External Trigger B (polarity insensitive)
13
I2A
Input 2 A (polarity insensitive)
3
I2B
Input 2 B (polarity insensitive)
9
O1
Output 1
(NPN or PNP short circuit protected
and software programmable)
8
O2
Output 2
16
O3
Output 3
14
RX
Auxiliary RS232 RX
4
TX
Auxiliary RS232 TX
7
ID+
ID-NET™ network +
15
ID-
ID-NET™ network -
Pin
Name
RS232
RS422 Full-Duplex
17
Main Serial
Port
(sw
selectable)
TX
TX+
11
RX
*RX+
12
-
TX-
10
-
*RX-
* do not leave floating. See Reference Manual for connection details.
M12 5-pin COM, Trigger Connector Pinout (PoE models)
Pin
Name
Function
1
I1A
External Trigger A (polarity insensitive)
2
RX
RS232 Main Serial Receive data signal
3
TX
RS232 Main Serial Transmit data signal
4
I1B
External Trigger B (polarity insensitive)
5
GND
RS232 Main Serial Reference signal
PoE models do not supply power to External Trigger.
M12 8-Pin Standard Ethernet Network Connector pinout
Pin
Name
Function
1
TX+
Transmit data (positive pin)
2
TX-
Transmit data (negative pin)
3
RX+
Receive data (positive pin)
4
RX-
Receive data (negative pin)
5
nc
Not Connected
6
nc
Not Connected
7
nc
Not Connected
8
nc
Not Connected
DPM Model
1
2
3
4
5
6
7
8
Standard Model
9
10
PoE Model
1
Reading Window (ESD model shown)
2
3
4
Bracket Mounting Holes (2)
Power On LED
Ethernet Connection LED
5
6
7
8
90° Rotating Connector Block
HMI X-PRESS™ Interface
Ethernet Connector
Power - COM - I/O Connector
9
10
Power Over Ethernet Connector
COM, Trigger Connector
12
11
14
13
17
15
16
17
18
18
15
16
17
18
Non Polarized Illuminators
Polarized Illuminators
Diffused Illuminators
Standard Illuminators (Top/Bottom)
M12 8-Pin Power Over Ethernet Network Connector pinout
Pin
Name
Function
1
TX+
Transmit data (positive pin)
2
TX-
Transmit data (negative pin)
3
RX+
Receive data (positive pin)
4
RX-
Receive data (negative pin)
5
DC1-
DC Power (negative pin)
6
DC2-
DC Power (negative pin)
7
DC1+
DC Power (positive pin)
8
DC2+
DC Power (positive pin)
Standard Model