PowerScanTM PBT7100 Base Station Quick Reference Guide
Datalogic ADC, Inc. 959 Terry Street Eugene, OR 97402 USA Telephone: (541) 683-5700 Fax: (541) 345-7140 ©2008 - 2013 Datalogic, Inc. An Unpublished Work - All rights reserved. No part of the contents of this documentation or the procedures described therein may be reproduced or transmitted in any form or by any means without prior written permission of Datalogic ADC, Inc. or its subsidiaries or affiliates ("Datalogic" or “Datalogic ADC”).
Table of Contents Statement of Agency Compliance ........................................................... 3 FCC Class B Compliance Statement .................................................. 3 Canadian Notice ............................................................................ 3 Solids and Water Protection ............................................................ 3 Power Supply ................................................................................ 3 Laser Cautions ..................
NOTES 2 PowerScanTM PBT7100 Base Station
Statement of Agency Compliance Statement of Agency Compliance This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Laser Cautions The imager may contain a laser pointer (this is a value-added option), which is certified in the U.S. to conform to the requirements of DHHS/CDRH 21CFR Subchapter J for Class II and IEC 60825-1 for Class 2 products. Class II (2) products are not considered to be hazardous.
Software Product Policy 2.2 on the Datalogic Product in which it is embedded (“designated Datalogic Product”), in machine-readable form only, solely for End User's internal business purposes. This Agreement does not convey ownership of the Software to End User. Title to the Software shall be and remain with Datalogic or the third party from whom Datalogic has obtained a licensed right.
7.4 ifications of End User, or 3) End User’s modification of the Datalogic Product without written authorization from Datalogic.
Getting Started Getting Started Connection shows how to connect the Base Station to a terminal, PC or other host device. Turn off the host before connection and consult the manual for that equipment (if necessary) before proceeding. Figure 1 Base Station Connection and Routing — Fully insert the Power Cable and Interface (I/F) Cable connectors into their respective ports in the underside of the Base Station (see Figure 1).
Host Connection — Typically, the interface type was specified at the time your reader and/or Base Station was ordered, however you should verify before connection that the Base Station’s cable type is compatible with your host equipment. Most connections plug directly into the host device as shown in Figure 2. Keyboard Wedge interface cables have a ‘Y’ connection where its female end mates with the male end of the cable from the keyboard and the remaining end at the keyboard port on the terminal/PC.
Getting Started Figure 3. Labeling and Nomenclature This illustration shows label placement ONLY. For actual regulatory, patent and other applicable information, view the labels on the product intself, or call your nearest sales or service office. Antenna Link Bar Code Link Button Amber LED Green LED Scanner Latch NOTE Regulatory Label (on underside) PowerScan® PBT7100 readers and Base Stations can be configured to be compatible with PowerScan® 7000BT imagers and Base Stations.
Select the desired interface by scanning the associated barcode below. INTERFACE SELECTION BARCODE RS-232 Standard RS-232 Wincor-Nixdorf RS-232 for OPOS/UPOS/ JavaPOS Wand Emulation IBM 46XX Port 5B IBM 46XX Port 9B USB HID POS USB Coma USB Keyboard USB Alternate Keyboard USB OEM a. 10 Download the correct USB Com driver from www.datalogic.
Getting Started Interface selection — continued INTERFACE SELECTION BARCODE Keyboard AT Keyboard Wedge for PS/2 25-286, 30-286, 50, 50Z, 60, 70, 80, 90 & 95 w/Standard Key Encoding Keyboard AT-NK Keyboard Wedge for IBM AT PS2 with standard key encoding but without external keyboard Keyboard AT-ALT Keyboard AT-ALT-NK Keyboard Wedge for AT, PS/2 25-286, 30-286, 50, 50Z, 60, 70, 80, 90 & 95 w/Alternate Key Keyboard Wedge for IBM AT PS2 with alternate key encoding but without external keyboard Keyboard
Interface selection — continued Keyboard IBM-MB Keyboard Wedge for IBM Terminals 31xx, 32xx, 34xx, 37xx make break keyboard Keyboard DIG-VT Keyboard Wedge for DIGITAL Terminals VT2xx, VT3xx, VT4xx Keyboard USB-KBDApple USB Keyboard for Apple computers Datalogic ADC Limited Factory Warranty Warranty Coverage Datalogic ADC (“Datalogic”) hardware products are warranted against defects in material and workmanship under normal and proper use.
Getting Started units and at its sole discretion can return the units in the “factory default” configuration or with any software or firmware update available at the time of the repair (other than the firmware or software installed during the manufacture of the product). Customer accepts responsibility to maintain a back up copy of its software and data.
(vi) any damage or malfunctioning caused by non-restoring action as for example firmware or software upgrades, software or hardware reconfigurations etc.; (vii) the replacement of upper window/cartridge due to scratching, stains or other degradation and/or (viii) any consumable or equivalent (e.g., cables, power supply, batteries, keypads, touch screen, triggers etc.).
Getting Started WEEE Statement Waste Electrical and Electronic Equipment (WEEE) Statement. English For information about the disposal of Waste Electrical and Electronic Equipment (WEEE), please refer to the website at www.datalogic.com. Italian Per informazioni sullo smaltimento delle apparecchiature elettriche ed elettroniche consultare il sito Web www.datalogic.com. French Pour toute information relative à l’élimination des déchets électroniques (WEEE), veuillez consulter le site internet www.
China RoHS 16 PowerScanTM PBT7100 Base Station
DECLARATION OF CONFORMITY 13 EC-094 Rev.:1 Pag.: 1 di 1 Datalogic ADC, Inc. 959 Terry Street Eugene, Oregon 97402 USA La presente dichiarazione di conformità è rilasciata sotto la responsabilità esclusiva di Datalogic ADC, Inc. per: This Declaration of Conformity is issued under the sole responsibility of Datalogic ADC, Inc.
www.datalogic.com ©2008-2013 Datalogic, Inc. All rights reserved. Datalogic and the Datalogic logo are registered trademarks of Datalogic S.p.A. in many countries, including the U.S.A. and the E.U. Datalogic ADC, Inc. 959 Terry Street | Eugene |OR 97402 | USA Telephone: (1) 541-683-5700 | Fax: (1) 541-345-7140 820025114 (Rev.