PowerScan™ M8300 Readers Industrial Handheld Laser Bar Code Reader with Datalogic’s STAR Cordless System™ Quick Reference Guide
Datalogic ADC, Inc. 959 Terry Street Eugene, OR 97402 USA Telephone: (541) 683-5700 Fax: (541) 345-7140 ©2009-2014 Datalogic, Inc. An Unpublished Work - All rights reserved. No part of the contents of this documentation or the procedures described therein may be reproduced or transmitted in any form or by any means without prior written permission of Datalogic ADC, Inc. or its subsidiaries or affiliates ("Datalogic" or "Datalogic ADC").
Table of Contents Using the PowerScan™ PM8300-DK .............................................................. 3 Scan Line Position ......................................................................................... 3 Reading Angle ................................................................................................ 3 Aiming System ............................................................................................... 4 Installing the Battery Pack..................................
Power Supply ............................................................................................... 23 Brazilian Certification Statements ........................................................ 26 WEEE Compliance ....................................................................................... 27 Numeric Table.....................................................................................................
PowerScan™ PM8300-DK 16-Key Reader Using the PowerScan™ PM8300-DK The PowerScan™ PM8300-DK series readers can be used with either an BC80X0 cradle or Stargate™ radio base station to build a Cordless Reading System for the collection, decoding and transmission of barcoded data. PowerScan™ PM8300-DK laser readers automatically scan barcodes at a distance. Simply aim and pull the trigger. Scan Line Position Code scanning is performed along the scan line emitted from the reading window.
Using the PowerScan™ PM8300-DK Aiming System PowerScan™ PM8300-DK provides an aiming system. If enabled, a partial trigger press produces a red spot, which should be aimed over the code center to get the best reading performance, see #1 in the figure above. By completely pressing the trigger the scan line appears to start the code scanning, see #2.
Installing the Battery Pack Installing the Battery Pack To install, charge and/or do any other action on the battery, follow the instructions in this manual. NOTE WARNING To charge the Battery Pack, See “Charging the Batteries” on page 7. Datalogic recommends annual replacement of rechargeable battery packs to ensure maximum performance. Do not discharge the battery using any device except for the scanner.
Installing the Battery Pack CAUTION Always charge the battery at 32° – 113°F (0° - 45°C) temperature range. Use only the authorized power supplies, battery pack, chargers, and docks supplied by your Datalogic reseller. The use of any other power supplies can damage the device and void your warranty. Do not disassemble or modify the battery. The battery contains safety and protection devices, which, if damaged, may cause the battery to generate heat, explode or ignite.
Installing the Battery Pack Charging the Batteries Once the BC-80X0/C-8000 is powered, you can charge the reader's batteries. Place the PowerScan™ PM8300-DK into the BC-80X0 cradle or the C-8000 battery charger. The "Reader" LED on the cradle/battery charger turns red. The battery is completely charged when the "Reader" LED on the cradle/battery charger turns green. To change the batteries, unscrew the retaining screw and extract the battery pack from the reader handle.
Setup Setup PowerScan™ PM8300-DK/BC-80X0 Point-to Point Configuration 1. 2. 3. 4. Connect a BC-80X0 cradle to the Host. For installation and connection information see the BC-80X0 Quick Reference Manual. Charge the PowerScan™ PM8300-DK battery using an BC-80X0 or the C-8000 charger as described in this Quick Reference manual. A full charge takes 4 hours if using an external power supply; while it takes up to 10 hours if supplying power through the USB port.
PowerScan™ PM8300-DK Configuration PowerScan™ PM8300-DK Configuration PowerScan™ PM8300-DK/BC-80X0 Point-to-Point Setup A rapid configuration procedure has been devised for point-to-point applications where a single reader is associated exclusively with its own BC-80X0 base station and where it is not necessary to set the Date and Time parameters.
PowerScan™ PM8300-DK Configuration PowerScan™ PM8300-DK/BC-80X0 Stand Alone Setup When the BC-80X0 cradle is connected and powered, configure the PowerScan™ PM8300-DK by reading the following codes in the given sequence and follow the instructions.. For the numeric code selection of steps 3, 4, and 5 use the table at the end of this Quick Reference manual. NOTE 1. Restore PowerScan™ PM8300-DK Default Ì$+$*oÎ 2. Enter Configuration Ì$+;Î 3.
PowerScan™ PM8300-DK Configuration 6. Exit and Save Configuration Ì$-?Î 7. Read the Bind code to pair the PowerScan™ PM8300-DK to the BC-80X0 cradle. The reader is dedicated to the cradle. Any previously bound reader will be excluded. To connect several readers to the same cradle see the following section "Using Multiple Readers with Same Cradle". Bind Ì$+RN0$-IÎ The green LED on the PowerScan™ PM8300-DK will blink: the reader is ready to be positioned onto the cradle. 8.
PowerScan™ PM8300-DK Configuration Using Multiple Readers with Same Cradle If you want to use several readers associated with the same cradle, you must first Bind the cradle with one of the readers (see previously described configuration procedure). Successive readers can be associated with the same cradle by following the configuration procedure substituting the Bind command with Join. 7.
PowerScan™ PM8300-DK/STAR-SYSTEM™ Setup PowerScan™ PM8300-DK/STAR-SYSTEM™ Setup The following procedure allows configuring a PowerScan™ PM8300-DK reader to communicate with various STAR-System™ devices such as Stargate™ RF base stations: 1. Restore PowerScan™ PM8300-DK Default Ì$+$*oÎ 2. Enter Configuration Ì$+;Î 3. Set Date ÌIA%Î + six digits for Day, Month and Year (DDMMYY). 4. Set Time ÌIB'Î + four digits for Hours and Minutes (HHMM). 5.
PowerScan™ PM8300-DK/STAR-SYSTEM™ Setup 6. Set Radio Address ÌRF8Î + four digits from the Numeric Table for the PowerScan™ PM8300-DK Address (from 0000 to 1999). All readers used in the same area must have different addresses. 7. Set First STAR-System™ Address ÌRSRÎ + four digits from the Numeric Table in the range 0000 to 1999 8. Set Last STAR-System™ Address ÌRTTÎ + four digits from the Numeric Table in the range 0000 to 1999 NOTE 9.
Selecting the Operative Mode Selecting the Operative Mode The PowerScan PM8300-DK has two basic operative modes. Simple Data Input Mode In Simple Data Input Mode, data entered manually on the keypad is transmitted to the host once the enter key is pressed. The data can be transmitted in one of three ways: 1. With the same formatting of the read barcode; 2. 3. With a specifically defined formatting; Without additional information.
PowerScan™ PM8300-DK Default Configuration PowerScan™ PM8300-DK Default Configuration DATA FORMAT code identifier disabled, field adjustment disabled, code length not transmitted, character replacement disabled CODE SELECTION enabled codes • EAN 8/EAN 13 / UPC A/UPC E without ADD ON check digit transmitted, no conversions • Interleaved 2/5 check digit control and transmission, variable length code; 4-99 characters • Standard Code 39 no check digit control, variable length code; 1-99 characters • Code 128 v
Technical Features Technical Features Electrical Features Battery Type 2150 Li-Ion battery pack Time of recharge max. 4 hours with external power supply max. 10 hours with Host power Operating autonomy (continuous reading) 60,000 reads (typical) Display LCD 4 lines x 16 chars Programmable LED backlight Indicators Good Read LED green Good Read Spot green Beeper Laser Features M8300-DK M8300-DKAR Power (max) in mW 0.9 mW 1.
Reading Tables Reading Tables PowerScan™ M8300 mil Typical reading distance with good quality codes 5 2.1 - 13.3 cm / 0.8 - 5.2 in 7,5 3.5 - 24.2 cm / 1.4 - 9.5 in 10 2.9 - 42.8 cm / 1.1 - 16.8 in 13 2.3 - 55.1 cm / 0.9 - 21.7 in 20 6.3 - 78.5 cm / 2.5 - 30.9 in 40 2.5 - 97.8 cm / 1.0 - 38.5 in PowerScan™ M8300 AR mil Typical reading distance with good quality codes 7,5 18 - 50 cm / 7.0 - 19.7 in 10 18 - 85 cm / 7.0 - 33.5 in 15 15 - 165 cm / 5.9 - 65.0 in 20 12 - 210 cm / 4.
Datalogic ADC Limited Factory Warranty Datalogic ADC Limited Factory Warranty Warranty Coverage Datalogic warranties this product against defects in workmanship and materials, for a period of 3 years from the date of shipment, provided that the product is operated under normal and proper conditions. Datalogic ADC ("Datalogic") hardware products are warranted against defects in material and workmanship under normal and proper use.
Datalogic ADC Limited Factory Warranty products which Datalogic, at its sole discretion, determines are not defective or eligible for warranty repair.
Service and Support Risk of Loss Customer shall bear risk of loss or damage for product in transit to Datalogic. Datalogic shall assume risk of loss or damage for product in Datalogic's possession. In the absence of specific written instructions for the return of product to Customer, Datalogic will select the carrier, but Datalogic shall not thereby assume any liability in connection with the return shipment.
Compliance Compliance This device must be opened by qualified personnel only. The batteries must be removed before opening the device. FCC Compliance Modifications or changes to this equipment without the expressed written approval of Datalogic could void the authority to use the equipment. This device complies with PART 15 of the FCC Rules.
Compliance The laser scanner utilizes a low-power laser diode. Although staring directly at the laser beam momentarily causes no known biological damage, avoid staring at the beam as one would with any very strong light source, such as the sun. Avoid that the laser beam hits the eye of an observer, even through reflective surfaces such as mirrors, etc.
24 X ܝᄺ㒘ӊ ܝᄺ㒘ӊ Assy, Module O O O ᳮ Mercury (Hg) O O O 叏 Hexavalent Chromium (Cr(VI)) Polybrominated biphenyls (PBB) O O O ચ卲 O O O ᄙᄽ侶 Ქኂ‛凝ᚗర⚛ Cadmium (Cd) O O O ᄙᄽԲㅘ Polybrominated diphenyl ethers (PBDE) O ઍᱝẊㇱઙ⊛ᚲဋ凝ޗறխࢬܶऱ具Ẋڶڶ୭ढ凝݁܅Պխ䦀Գا٥ࡉ㧺ॾஒ䣈䢓ຝᚲ咒ؒ⊛ ޝ䶣ॾஒ䣈խڶڶ୭ढ凝ऱૻၦޣρ(SJ/T 11363-2006) 億ࡳऱૻၦޕ X: ઍᱝẊㇱઙᚲ↪⊛ဋ凝ޗறխ, ⥋ዋ৻㮕᧚ᢱᚲ⊛Ქኂ‛凝Պխ䦀Գا٥ࡉ㧺ॾஒ䣈䢓ຝᚲ咒ؒ⊛ ޝ䶣ॾஒ䣈խڶڶ୭ढ凝ऱૻၦޣρ(SJ/T 11363-2006) 億ࡳऱૻ㊂ X ⬉䏃ᵓ㒘ӊ X 卋 Assy, Optics Block ㇱઙฬ⒓ Pr
Quick Reference Guide X X ㇱઙฬ⒓ ⬉䏃ᵓ㒘ӊ ܝᄺ㒘ӊ Printed Circuit Board Assembly Assy, Module O O 叏 Hexavalent Chromium (Cr(VI)) Polybrominated biphenyls (PBB) O O ચ卲 O O ᄙᄽ侶 Ქኂ‛凝ᚗర⚛ Cadmium (Cd) O O ᄙᄽԲㅘ Polybrominated diphenyl ethers (PBDE) O ઍᱝẊㇱઙ⊛ᚲဋ凝ޗறխࢬܶऱ具Ẋڶڶ୭ढ凝݁܅Պխ䦀Գا٥ࡉ㧺ॾஒ䣈䢓ຝᚲ咒ؒ⊛ ޝ䶣ॾஒ䣈խڶڶ୭ढ凝ऱૻၦޣρ(SJ/T 11363-2006) 億ࡳऱૻၦޕ X: ઍᱝẊㇱઙᚲ↪⊛ဋ凝ޗறխ, ⥋ዋ৻㮕᧚ᢱᚲ⊛Ქኂ‛凝Պխ䦀Գا٥ࡉ㧺ॾஒ䣈䢓ຝᚲ咒ؒ⊛ ޝ䶣ॾஒ䣈խڶڶ୭ढ凝ऱૻၦޣρ(SJ/T 11363-2006) 億ࡳऱૻ㊂ O O ᳮ 卋 PART Mercu
Compliance Cofetel Mexico Statement Cofetel Mexico Update Este producto es usable en México. Certificado Nr. RCPDAST08-0269 (COFETEL).
Compliance WEEE Compliance Waste Electrical and Electronic Equipment (WEEE) Statement English For information about the disposal of Waste Electrical and Electronic Equipment (WEEE), please refer to the website at www.datalogic.com. Italian Per informazioni sullo smaltimento delle apparecchiature elettriche ed elettroniche consultare il sito Web www.datalogic.com. French Pour toute information relative à l’élimination des déchets électroniques (WEEE), veuillez consulter le site Internet www.datalogic.com.
Numeric Table Numeric Table Ì01Î 0 Ì12Î 1 Ì23Î 2 Ì34Î 3 Ì45Î 4 Ì56Î 5 Ì67Î 6 Ì78Î 7 Ì89Î 8 Ì9:Î 9 28 PowerScan™ PM8300-DK 16-Key Reader
DECLARATION OF CONFORMITY 13 Datalogic ADC Srl, Via S. Vitalino, 13 Lippo di Calderara di Reno (BO) 40012 Italy EC-054 Rev.: 4 Pag.
www.datalogic.com ©2009-2014 Datalogic, Inc. • All rights reserved. Datalogic and the Datalogic logo are registered trademarks of Datalogic S.p.A. in many countries, including the U.S.A. and the E.U. Datalogic ADC, Inc.
