Quick Start Guide

Battery Swap
Battery Swap mode is a low power suspend mode that allows you to replace the battery pack without
closing files and applications. Datalogic has a patent pending on the unique LED notification, called "Safe
Swap" for application data protection.
To switch to Swap Battery mode follow the steps below:
1. Press and hold the Power button to display the Long Press Menu and tap Battery Swap > Confirm.
2. The charging LED starts blinking blue. The battery swap LEDs light up solid red:
3. Wait for the LEDs to turn solid green to replace the battery.
4. Press and release the power button to resume your session. The charging LED turns off.
Replace the battery pack within 90 seconds after its removal from the device.
NOTE
Be sure to insert a charged battery pack. If the battery is fully discharged, the device will turn off
and your session data will be cleared.
The battery swap procedure is not available when the device is connected via USB cable.
Do not insert or replace SIM cards during the battery swap procedure.
The battery swap procedure is not available if the Ni-MH battery is fully discharged.
The spare battery pack is configured in ship mode at the factory. Before inserting a new battery,
charge it with the CHARGER, 4 SLOT BATTERY, MEMOR 20 (available as accessory, p/n 94ACC0246).
CAUTION
SIM Card Installation
Memor 20 supports up to two nano SIM cards.
1. Turn off the Memor 20.
2. Press the battery latches and remove the battery pack:
3. Pull the rubber label to remove the SIM door, then open the SIM card tray:
4. Place the nano SIM card in the tray with the written part upward and close the SIM tray.
5. Reinsert the SIM door and press it.
6. Reinsert the battery (see Battery Installation).
Scanning and Imaging
2D Imager Data Capture
To scan a bar code symbol:
1. Point the scan window at the bar code.
2. Press one of the scan triggers. The imager projects a laser aiming pattern that is used to position the
barcode or object within the field of view.
3. Center the symbol in any orientation within the aiming pattern. Ensure the entire symbol is within
the rectangular area formed by the brackets in the aiming pattern, then either wait for the timeout
or release the Scan Key to capture the image. A red beam illuminates the symbol, which is captured
and decoded.
If the scan has been successful:
y If enabled, the good read beep plays.
y If enabled, the GreenSpot projects a green spot onto the bar code image.
y If enabled, the good read indicator positioned at the top left side of the display glows solid green.
Linear Bar Code
2D Matrix Symbol
Relative Size and Location of Aiming System Pattern
Charging Instructions
The battery pack is not initially fully charged. After installing the battery, charge it with the USB Type-C or
with a dock (single slot dock, 3-slot dock, vehicle dock, 4-slot battery charger).
During the charging process the charging LED positioned at the top left side of the display glows red
constantly. Once the charging process has been completed, the charging LED glows green constantly.
Charge with USB
Use the provided USB Type-C cable in conjunction with the power supply adapter to charge the device
from a power outlet.
The charger is modular, with one adapter and five switchover plugs.
You can also use the USB cable to charge the Memor 20 from any self-powered USB hub or USB port on
a computer.
Use only the Datalogic power supply 94ACC0249 POWER SUPPLY USBC, DEVICE/DOCK, MEMOR 20
to power the Memor 20.
CAUTION
Charge with the Dock
Insert the device into the dock with the screen facing front and the head facing up.
Use only a Datalogic approved power supply to power any of the docks.
Do not put any foreign object such as, but not limited to, coins, paper clips, stickers inside the slot
of any of the docks.
Do not apply any sticker to the Memor 20 (see the examples below).
CAUTION
The Memor 20 may get warm during charging. This is normal and does not mean a malfunction.
For information on the single slot dock/ 3-slot dock/ vehicle dock/ 4-slot battery charger refer to
the Quick Start Guide included in the dock's box.
NOTE