QLM700 INSTALLATION MANUAL 7 8 9 6 5 4 3 10 1 2 Figure A 1 Power In Connector and LED 6 Profinet IO Port 2 Connector and LED 2 ID-NET Connector and LED 7 Auxiliary Port Connector 3 Trigger Connector and LED 8 IP Address Selectors (last octet) 4 I/O Connector and LED 9 Reading Device Connector 5 Profinet IO Port 1 Connector and LED 10 Mounting slots (6) 821002140
QLM700 INSTALLATION MANUAL UPDATES AVAILABILITY UK/US The latest documentation updates for this product are available on Internet. Log on to: www.automation.datalogic.com I Su Internet sono disponibili le versioni aggiornate di documentazione di questo prodotto. Collegarsi a: www.automation.datalogic.com F Les versions mises à jour de documentation de ce produit sont disponibles sur Internet. Cliquez sur : www.automation.datalogic.
QLM700 INSTALLATION MANUAL DESCRIPTION The QLM700 Profinet IO Gateway is an active connection module which can be used in Standalone or ID-NET™ Master Multidata, or Master Synchronized layouts. It provides a fast and efficient way to cable both an Profinet IO network and an ID-NET™ network using standard cables. It provides separate M12 connectors for Power Supply, Profinet Communication, ID-NET™ Network, External Trigger, Digital I/O and Aux RS232 Communication for configuration of the reading device.
QLM700 INSTALLATION MANUAL PACKAGE CONTENTS Verify that the QLM700 and all the parts supplied with the equipment are present and intact when opening the packaging; the list of parts includes: QLM700 Gateway This Installation Manual Mounting screws and washers (2) M12 protection caps (5) pre-mounted Figure 1 - Package Contents ACCESSORIES The following accessories are available on request for the QLM700: Name Description Field Mountable Connectors CBL-1487 PWR-IN CONNECTOR M12 5P F.
QLM700 INSTALLATION MANUAL MECHANICAL INSTALLATION QLM700 can be mounted to various surfaces using the two M5x20 screw and washers included in the package: The M5x20 screws can be used to mount the QLM700 to metallic/plastic surfaces already prepared with M5 threaded holes. QLM700 can also be mounted to a Bosch Frame using the two M5x20 screws included in the package, plus two specific commercial T-nuts (for example the Bosch Rexroth T-nut 10 M5, cod. 3 842 530 283).
QLM700 INSTALLATION MANUAL ELECTRICAL CONNECTIONS CONNECTORS PWR-IN (Power In) M12 5P Male (A-coded) Pin Function 1 Vdc 2 nc 3 GND 4 nc 5 nc ID-NET (Out) M12 5P Female (A-coded) Pin Function 1 Shield 2 Vdc 3 GND 4 ID+ 5 ID- 4 5 3 1 2 TRG (Trigger) M12 4P Female (A-coded) Pin Function 1 +V (I/O) 2 nc 3 -V (I/O) 4 I1+ (trigger) 4 2 1 AUX M12 5P Female (B-coded) Pin Function 1 nc 2 RXA 3 GND 4 TXA 5 nc 4 1 3 2 4 4 2 6 5 7 8 4 1 3 ETH2 (Profinet IO Port 2) M12 4P Female (D-coded) Pin Function
QLM700 INSTALLATION MANUAL PWR-IN PWR-IN is a 5-pin Male A-Coded M12 connector. Input power must only be supplied to the QLM700 at the PWR-IN connector; from there it is internally distributed to the connected reading device, the ID-NET™ network and all the I/O devices. You can use the CBL-1487 connector and follow the pinout above to build your own Power Supply connector cable. You can also use one of the CS-A2-02-G-xx cables which terminate in four single stranded wires.
QLM700 INSTALLATION MANUAL Pins 2 and 3 on the ID-NET connector carry the same power supply lines present on pins 1 and 3 of the PWR-IN connector; however power must only be supplied to the QLM700 through the PWR-IN connector. In an ID-NET™ network, the reading device connected to the QLM700 must be configured as an ID-NET™ Master; to facilitate the network setup, the QLM700 already provides an internal bus termination resistor (the Master is the first device of the chain).
QLM700 INSTALLATION MANUAL ETH1 CONNECTOR ETH1 is a 4-pin Female D-Coded M12 connector. It is used to connect the QLM700 to a Profinet IO network in either Daisy-Chain bus, or Star topologies. ETH2 CONNECTOR ETH2 is a 4-pin Female D-Coded M12 connector. It is used to connect the QLM700 to a Profinet IO network in either Daisy-Chain bus, or Star topologies. AUX CONNECTOR AUX is a 5-pin Female B-Coded M12 connector.
QLM700 INSTALLATION MANUAL 10) Preset the Node Address of the QLM700, as shown in the Profinet IO Network Address Selectors paragraph. 11) Switch on the power supply; after a while (the system needs some seconds to boot), and if the Profinet IO Host is ready and has correctly recognized the QLM700, the green Network Status and Module Status LEDs below both ETH1 and ETH2 M12 connectors should be turned on.
QLM700 INSTALLATION MANUAL INDICATOR LEDS There are six Indicator LEDs which signal power, I/O and Profinet IO communication activity and are visible below the M12 connectors (excluding AUX). PWR-IN / ID-NET The Power LEDs are blue when power is correctly applied to the QLM700. These LEDs are red if power polarity is incorrect. In this case the QLM700 and the connected reading device are protected.
QLM700 INSTALLATION MANUAL TYPICAL LAYOUTS The following figure shows the general system layout. Reading Device Reader Configuration PC Auxiliary Interface protection cap or to next Profinet IO node QLM700 Power from previous Profinet IO node ID-NET™ Trigger or I/O from Profinet IO PLC (Host) Figure 4 – General System Layout The dotted lines in the figure refer to optional hardware configurations.
QLM700 INSTALLATION MANUAL The following diagrams are examples showing layout connections and are not intended to represent power limits, which instead, depend on each specific application. See "Voltage Drop and Max Distributed Current Calculations".
QLM700 INSTALLATION MANUAL TECHNICAL FEATURES ELECTRICAL FEATURES Supply Voltage Consumption Maximum Distributed Current Allowed ID-NET™ Limited Current Consumption QLM700 + reading device Trigger + I/O device (see related device manuals) Inputs: Input1 (TRG), Input 2 Voltage Current Consumption Outputs: Output 1, Output 2 VCE Collector Current VCE Saturation Power Dissipation 10 to 30 Vdc 0.3 - 0.2 A 4.0 A max 1.85 A max 0.75 A max Optocoupled 30 Vdc max. 12 mA max. Optocoupled 30 Vdc max.
QLM700 INSTALLATION MANUAL COMPLIANCE POWER SUPPLY This product is intended to be installed by Qualified Personnel only. This device is intended to be supplied by a UL Listed or CSA Certified Power Unit with Class 2 or LPS power source. Total power consumption is given by adding the QLM700 power consumption to that of all the devices powered through the QLM700 (reading device, P.S., I/O).
DECLARATION OF CONFORMITY EC-128 Rev.: 2 Pag.: 1 di 1 Datalogic Automation S.r.l. Via Lavino 265 40050 Monte San Pietro Bologna - Italy www.automation.datalogic.
