Datasheet SDC‐PE15N
SDC‐PE15N Datasheet CONTENTS Scope ............................................................................................................................................................ 3 Specifications ............................................................................................................................................... 3 Pin Definitions ............................................................................................................................................
SDC‐PE15N Datasheet SCOPE This document describes key hardware aspects of the SDC‐PE15N embedded wireless LAN module. This document is intended to assist device manufacturers and related parties with integration of this module into their host devices. Data in this document are drawn from a number of sources and includes information found in the Broadcom BCM4322 data sheet issued in August of 2008. The information in this document is subject to change without notice.
SDC‐PE15N Datasheet Feature Description QPSK @ 2, 12, 18, 29, 43, 60, 90 Mbps CCK @ 5.5,11 Mbps 16‐QAM @ 24, 36, 58, 87, 120, 180 Mbps 64‐QAM @ 48, 54, 116, 130, 144, 240, 270, 300 Mbps Regulatory Domain Support FCC (Americas, Parts of Asia and Middle East) ETSI (Europe, Middle East, Africa and Parts of Asia) MIC (formerly TELEC) (Japan) KCC (Korea) 2.4 GHz Frequency Bands ETSI 2.4 GHz to 2.483 GHz FCC 2.4 GHz to 2.473 GHz MIC 2.4 GHz to 2.495 GHz KCC 2.4 GHz to 2.
SDC‐PE15N Datasheet Feature Description NCC Certification Wi‐Fi Alliance 802.11a, 802.11b, 802.11g, 802.11n WPA Enterprise WPA2 Enterprise Cisco Compatible Extensions(Version 4) Certifications Warranty 3‐Year Warranty All specifications are subject to change without notice PIN DEFINITIONS Pin # Pin Name I/O Power Type 1 WL_GPIO_1 O VDDIO 2 VCC3_3 3 WLAN_ACTIVE O VDDIO 4 GND I VDDIO Description Wake on Wireless – Not currently supported in the software. May be left open 3.
SDC‐PE15N Datasheet Pin # Pin Name 21 GND 22 PERST_L 23 PETn0 24 VAUX_3_3 25 PETp0 26 GND Ground 27 GND Ground 28 No Connect 29 GND 30 No Connect 31 PERn0 32 No Connect 33 PERp0 34 GND Ground 35 GND Ground 36 No Connect 37 GND 38 No Connect Not Used. Leave Open (Float) 39 VCC3_3 Primary 3.3 V Module Power 40 GND 41 VCC3_3 Primary 3.3 V Module Power 42 No Connect Not Used. Leave Open (Float) 43 No Connect Not Used.
SDC‐PE15N Datasheet MECHANICAL SPECIFICATIONS Connector Overview Mounting The SDC‐PE15N is fully compliant with the PCIe full length Mini Card mechanical specifications. As such, it may be connected to the host device via any standards‐compliant host connector. It may be mounted to host devices using a variety of standards‐compliant latches and or via the two mounting holes located on the top end of the device.
SDC‐PE15N Datasheet Summit recommends the use of a double shielded 32 AWG cable for the connection between the radio and the antenna elements. REGULATORY Note: Operation in the 5150‐5250 MHz band is limited to indoor use only. Remarque: Le fonctionnement dans la bande 5150‐5250MHz est limité à l'utilisation à l'intérieur seulement.
SDC‐PE15N Datasheet Certified Antennas The SDC‐PE15N provides two Hirose U.FL type antenna connectors to support transmit and receive diversity. For single antenna, non‐diversity applications, OEMs are advised to use the Main (not Aux) antenna connector and should disable transmit and receive diversity from the Global tab of the Summit Client Utility (SCU) software utility. Notice: The module is professionally installed device and installed in industry computer that is generally for industrial use.
SDC‐PE15N Datasheet European Union) outline the information that must be included in the user’s guide and external labels for the host devices into which the SDC‐PE15N is integrated. FCC User’s Guide Requirements As outlined in the Operational Description, the SDC‐PE15N complies with FCC Part 15 Rules for a signal Modular Approval. To leverage Summit’s grant, the two conditions below must be met for the host device into which the SDC‐PE15N is integrated: 1.
SDC‐PE15N Datasheet 2. Increase the separation between the equipment and receiver. 3. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. 4. Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This device complies with Part 15 of the FCC Rules.
SDC‐PE15N Datasheet compliance requirements required with this module installed, such as (but not limited to) digital device emissions and PC peripheral requirements. Comme indiqué dans la description opérationnelle, la SDC‐PE15N est conforme aux règles d'Industrie Canada (IC) pour un signal d'approbation modulaire. Pour tirer parti de la subvention du Sommet, les deux conditions suivantes doivent être remplies pour le périphérique hôte dans lequel la SDC‐PE15N est intégrée: 1. 2.
SDC‐PE15N Datasheet When using Summit’s IC grant for the SDC‐PE15N, the integrator must include specific information in the user’s guide for the device into which the SDC‐PE15N is integrated. The integrator must not provide information to the end user regarding how to install or remove this RF module in the user’s manual of the device into which the SDC‐PE15N is integrated.
SDC‐PE15N Datasheet 8dBi (5.47‐5.
