Manual

ManualsBrandsDatamax-O'Neil ManualsPrintersVMP-1000_2000 Dashmount Bracket

Choosing a location for the Dashmoun t Brack et:

1. Position the bracket/printer with enough room to properly

open and close the printer.

2. Position the bracket/printer so it is protected from

environmental elements (i.e. moisture, tools, boxes, etc.).

3. Position the bracket/printer in a visibly secure area in

normal trac patterns.

4. DO N OT position the bracket a bove, near or re lative to

the driver’s position as to interfere with normal driving

operations.

5. Moun t the bracket/printer away from th e dri ver ’s hea d

to eli mina te poten tial injur y in the event of an

accident.

6. Cabling – All power to the printer must be fused. Connect

fuse box properly.

Cradl e

Brkt.

Vi br ation I s olati on Brkt.

Fig. 2

The Dashmount Bracket with Paper Tray (220151-000 )

comes with the following ( Fig. 1 ):

• (1) Dash Mounting Plate

• (1) Printer Mounting Plate

• (1) Paper Tray

• (2) Endcaps

• (1) Foam Block

• (8) ¼ - 20 x 1 ¼ ” Cap Screw

• (8) ¼ - 20 Lock Nut

• (8) ¼ - 20 Flat Washer

• (4) #8 -32 x ¼” Screw, Button he ad with L ocking Spot

• (1) #8 -32 x 5/8” Screw , Phillips Pan head w/ Locking Spot

• (4) #10 -32 x 5/8” Screw , Phillips Pan head w/ Locking

Spot

• Assembly Instructions

AS SEMBLY RE QUIRED

The Deluxe Dashmoun t Bracket w/ Paper Tra y ( 220154-000)

comes with the a bove items and the following (Fi g. 2):

• (1) Vibration Isolation Bracket Kit (220146 -000 )

• (4) 10 -32 x 1” Truss Machine Screw

• (4) ¼ - 20 Flat Washer

• (1) Cradle Bracket Kit (220153 -00 0)

• (3) ¼ - 20 x 2” Socket Head cap Screw

• (3) ¼ - 20 Flat Washer

• (3) ¼ - 20 Lock Nut

• Assembly Instructions

AS SEMBLY REQUIRED

Tools required for assembly:

• 7/16” Socket w/ ratchet wrench

• 3/16” Allen wrench (hex key)

• 3/32” Allen wrench (hex key)

• #1 Phillips screwdriver

Foam Block

Printer

Mounting

Plate

Dash

Mounti ng

Plate

Paper Tray

Endcaps

2 pcs.

Assembl y

Instructions

F ig. 1

As s embly o f the Cradle Bracket (Deluxe Ki t):

Cradle Bracket (220153-000) is included with the Deluxe

Kit (220154-000) . It is also available separately. For the

Dashmount Kit (220151-000), which does not have the

Cradle Bracket, continue with the installation of the Paper

Tra y ( See next section).

2. Assemble the Cradle Bracket to either the left or right side

of the Dashmount with (3) ¼ - 20 x 2” Screws, (3 ) ¼ -20

Washers, and ( 3) ¼ -20 Lock Nuts ( Fig s . 9 & 10 ). In

addition, the Cradle Bracket may be installed at dierent

angles ( Figs. 11 & 12 ).

Install the pivot screw ( ¼ -20 x

2”) rst to deter mine the angle of the Cradle Bracket.

Insert the screws from the outside through the Cradle

Bracket and then the Endcap. Place the washer over the

exposed threads of the screw and tighten the assembl

together with the locking nuts. Side location and angle o

Cradle Bracket is based on user requirements. Be careful

not t o o ver tigh ten as it may compress and damage

the Endcaps .

3. Secure the Cradle Bracket, once the appropriate location

and angle are de termined, with the remaining hardware in

the appropriate angle adjustment holes.

F ig. 12

Angle adju st ment holes

F ig. 11

F ig. 10

Pi vot

screw

F ig. 9

As s embly o f the Dash mo unt Bracket:

1. Either Endcaps may be used on the left or right side.

Assemble the Endcaps to the Dash Mounting Plate using

(4) ¼ - 2 0 x 1 ¼ ” Screws, (4) ¼ -20 Washer, and (4) ¼ -

20 Lock Nuts. Insert the screws from the outside through

the Dash Mounting Plate and then the Endcap. Place the

washe r over the exposed t hreads of the screw and tighten

the assembly together with the locking nuts. Use a ratchet

wrench with 7/16” socket and 3/16” Allen wrench ( Fig. 3 ).

Be careful not to o verti ghten a s it may compress and

damage t he Endcaps. The screw shaft should protrude

no more tha n 1/8” past the nylon of the lock nut.

2. The Dashmount should appear e xactly as in Fi g. 4 .

3. The Printer Mounting Plate may be positioned in t wo

ways. First option ( Fi g. 5 ) is with the paper exiting the

printer up the angled Dashmount. Second option (

Fig. 6 )

is w ith the pap er exiting do wn the angled Dashmount.

The user will determine the direction of the paper f eed.

4. Assemble the Printer Mounting Plate onto the Endcaps

using (4) ¼ - 20 x 1 ¼” Screws , ( 4) ¼ -20 Washer, and (4)

¼ -20 Lock Nuts (Fig. 7 ). Be careful not to over tighten

as it ma y compress and damage t he Endcaps . T he

screw shaft should protrude no more than 1/8 ” past the

nylon of the lock nut.

. 6

Fig. 5

. 7

Fig. 3

Washer

& Nut

Fig. 4

Screw

Fig. 3

Summary of content (2 pages)

PAGE 1
F ig. 1 Foam Block Paper Tray Fig . 2 Vi br ati on I s ol ati on Br kt. Assembly Instructions Endcaps 2 pcs. Cradl e Brkt. Dash Mounting Plate As s embly o f the Dash mo unt Bracket: 1. Either Endcaps may be used on the left or right side. Assemble the Endcaps to the Dash Mounting Plate using (4) ¼ - 2 0 x 1 ¼ ” Screws , (4) ¼ -20 Washer, and (4) ¼ 20 Lock Nuts. Insert the screws from the outside through the Dash Mounting Plate and then the Endcap.
PAGE 2
110092-002 As s embly o f the Paper Tray: As s embly o f the Vibrati on Isol ation Bracket (Deluxe Kit): 1. 1. 2. Assemble the Paper Tray to the Dash Mounting Plate with (4) #8-32 x ¼” Button head Screw s with 3/32” Allen wrench ( Fig. 13 ). Paper Tr ay ma y be installed with long end towards the user or away from the user, depending on dashboard configuration. The Dashmount with Paper Tra y and Foam Block (smooth side up) should appear as in Fig.14 .