Instructions

UM-0085-B09 DT80 Range User Manual Page 242
RG
In this example the DT80 has IP address 192.168.0.1 configured for the WIFI interface. The WIFI Interface of the logger
configured in Access Point mode, passed initialization and currently in Joined state. It uses RF Channel 1 and Security
mode PSK WPA2 (Pre-Shared Key WPA2), having Ethernet Address 00:23:a7:5c:db:9c and subnet mask
255.255.255.0.
No DNS servers configured, because of the mode and the interface statistics shows no traffic occurred through the
interface yet. Embedded DHCP Server statistics shows it has one DHCP Client connected to the interface with the IP
Address 192.168.0.2 corresponding to the MAC Address c8:3a:35:b0:12:eb.
Subsequent examples shows other commands end their execution feedbacks.
Setting WiFi Parameters
All WiFi parameters are set using profile settings (see Profile Settings (P264)), i.e.
PROFILE WIFI key=value
The following keys are defined:
Key
Value
Default
ENABLE
Set to YES to enable the Ethernet port, NO to disable (saves power)
YES
IP_ADDRESS
IP address of DT80 Ethernet port. May be set to a static IP address, or
AUTO
(obtain an address from a DHCP server). This option has effect only in the
client operating mode.
AUTO
SUBNET_MASK
Subnet mask for the network segment to which the DT80 is connected. This
setting will be ignored if a valid subnet mask was obtained from the DHCP
server. This option has effect only in the client operating mode.
255.255.255.0
GATEWAY
IP address of the gateway computer/router for network segment to which the
DT80 is connected. This setting will be ignored if a valid gateway address
was obtained from the DHCP server. This option has effect only in the client
operating mode.
0.0.0.0
OPER_MODE
Interface operating mode. Currently, two modes are available:
• Client
• Access Point
There are different configuration options and interface features for each
mode
ACCESS_POINT
SECURITY_MODE
Interface for security mode. There are 4 modes are available:
• OPEN
• PSK_WEP
• PSK_WPA
•
PSK_WPA2
PSK_WPA2
PSK
The pre-shared key. Mandatory option for the pre-shared key configurations.
DATATAKER
SSID
The service set identifier of the wireless network depending on operation
mode:
• represents the name of logger wireless network (Access Point mode)
• represents the name of the available network where the logger’s WiFi
Interface can be connected (Client mode)
DT80S4_AP
HIDDEN_SSID
Disable broadcasting of the network SSID to make the network invisible for
the network scanning procedure. The option has effect only in the Access
Point mode.
NO
METRIC
Assign the interface metric for the WiFi interface. The option has effect only
in the Client mode.
30
DNS_SERVER_1
1
st
DNS Server address available for the names resolution on the WiFi
Interface. The option has effect only in the Client mode.
DNS_SERVER_2
2
nd
DNS Server address available for the names resolution on the WiFi
Interface. The option has effect anly in the Client mode.
WLAN_AGGREGATION
Control WLAN Aggregation feature on the WiFi Interface belongs to the
802.11n standard.
Allowing to speed up the communications (in-case of the other side
compliance) by enabling aggregation of multiple data packets in one when
transmitted over the WLAN.
NO
ANTENNA_SEL
Control the type of antenna being used by the WiFi interface module for RF
communications. There are two options available: EXT (external antenna)
and INT (internal antenna).
For the better connection quality of service, we would not recommend to
switch from using external antenna unless there are specific requirements.
EXT
ENCRYPT_MODE
Encryption mode for the WLAN traffic (Access Point mode)
• NONE
• TKIP (temporal key integrity protocol)
• CCMP (Counter mode cipher block chaining message authentication code
protocol)
CCMP