ITC-100 KF1000 8 Channel Intercom / Talkback System for SE-1000 Instruction Manual http:// www.datavideo-tek.
Warnings and Precautions 1. Read all of these warnings and save them for later reference. 2. Follow all warnings and instructions marked on this unit. 3. Unplug this unit from the wall outlet before cleaning. Do not use liquid or aerosol cleaners. Use a damp cloth for cleaning. 4. Do not use this unit in or near water. 5. Do not place this unit on an unstable cart, stand, or table. The unit may fall, causing serious damage. 6.
Datavideo warrants that the equipment it manufactures shall be free from defects in material and workmanship for a period of 12 months from the date of product purchased. If equipment fails due to such defects, Datavideo will, at its option, repair or provide a replacement for the defective part or product.
Contents WARNINGS AND PRECAUTIONS 1 WARRANTY 2 INTRODUCTION 2 PACKING LIST 3 FRONT PANEL CONNECTIONS 4 REAR PANEL CONNECTIONS 6 ITC-100SL SLAVE UNIT 7 USING THE ITC-100 WITH THE SE-1000 / TB-10 9 ITC-100 TALLY INPUT PIN CROSS REFERENCE 10 SPECIFICATIONS 11 SERVICE AND SUPPORT 13 Packing List 1. ITC-100 KF 1000 Main Unit x 1 2. ITC-100SL Slave Unit x 6 3. ITC-100SL Carrying Case x 6 4. 20m XLR to XLR Intercom Cable x 6 5. MC-1 Headset / Microphone x 6 6.
Front Panel: On / Off Switch Powers the ITC-100 On / Off. Red LED indicates that unit is switched on. XLR Microphone Socket Combined XLR / ¼” (6.3mm) Jack Microphone Input for either a Condenser or Dynamic Gooseneck Microphone. XLR supports Condenser Microphones ¼” (6.3mm) Jack supports Dynamic. Headphone Socket ¼ “ / 6.3mm Stereo Headphone Socket for conventional headphones. Plugging in headphones will disable the built-in speaker Microphone / Headset Socket 3.
Channel Buttons 1~6 + AUX 1 / 2 Opens communication with individual channels. More than 1 channel can be active at any given time, active channels are illuminated red. All active channels will hear any communication from the operator or from any other active channel. The buttons will also indicate if any channel is paging, the paging channel will flash in orange until the page is answered. MUTE Button Mutes all communication from the base station or any channel. N.B.
Rear Panel: Channel Input / Output XLR Sockets Each of the 8 channels has an XLR connector that carries bi-directional signals between the ITC-100 and ITC-100SL. All connections are contained within the one cable. Channels 1 ~ 3 are supplied tally light information from tally A; channels 4 ~ 6 are supplied tally light information from tally B. Tally Inputs A & B Tally Inputs A & B are configured for direct connection to the Datavideo SE-1000 via the TB-10.
ITC-100SL Slave Unit : XLR Connection Connects the ITC-100SL to the ITC-100 Base Station. Power, tally and bi-directional audio are all carried through the same cable. Call Button Sends a paging message to the ITC-100 Base Station. The channel button will flash orange and there will be an audible tone, each time the button is pressed. Tally LED Will illuminate RED when the channel is LIVE Talk Button Opens up talk back communication with the ITC-100 base station, and any other active channels.
Mic / Headphone Socket The ITC-100SL has both a 3.5mm and 2.5mm Mic / Headset socket. A standard 3.5mm Mic / Headset can be used, or a Motorola type 2.5mm Mic / headset could be used if preferred. External Tally LED Socket An external tally display (TD-1) can be connected to the ITC-100SL. This enables the tally light to be positioned in a more convenient place, such as on top of the camera. When the channel is LIVE the LED will be RED, and when the channel is CUED the LED will be AMBER. N.B.
Using the ITC-100 KF1000 with the SE-1000 / TB10: The ITC-100 KF1000 is an ideal accessory for the Datavideo SE-1000 Vision Mixer. The SE-1000 has five HD / SDI channels, so in the diagram below we have five camera crew, each with an ITC-100SL. The sixth ITC-100SL could be for communicating with the graphics operator or other members of the crew. The Tally output from the SE-1000 connects to the TB-10; this provides the status of the SE-1000. The TB-10 Tally Out connects to the ITC-100 Tally Inputs A and B.
ITC-100 Tally Input - Pin Cross Reference If you are using the ITC-100KF1000 with a Datavideo SE-1000 via a TB-10 you do not need to worry about tally information, as it is automatically sent to the ITC-100 KF1000. If you are using the ITC-100 with other equipment the following tables explain the pin configurations of Tally A and Tally B. Contact closure between the relevant Pin number and ground will illuminate the LED.
Specification: ITC-100 Base Station Specification POWER 12V 2.5A TALLY 2 x 15 Pin SubD Sockets for Tally A and Tally B MIC / HEADSET 3.5mm Stereo Jack Socket for combination Headphone / Microphone Headset Impedance 8~600 ohms 100mW(min) INPUTS / HEADPHONE OUTPUTS ¼” (6.3mm) Stereo Headphone Socket Headset Impedance 8~600 ohms 100mW(min) LIGHT SOCKET 3 pin XLR connector. Pin2: 12V, Pin3: GND. (12V DC) Light power consumption 12V/100mA(max). MICROPHONE 3 Pin XLR / ¼” (6.
ITC-100SL SLAVE Unit Specification INPUT 5 Pin XLR Connector MIC / HEADSET SOCKET 3.5mm Stereo Jack Socket for combination Headphone / Microphone Headset Impedance 8~600 ohms 100mW(min) Microphone Level -67dB Or 2.5mm Stereo Jack Socket, for Motorola Mobile Phone type headset / microphone TALLY OUT SOCKET 3.
Service and Support It is our goal to make your products ownership a satisfying experience. Our supporting staff is available to assist you in setting up and operating your system. Please refer to our web site www.datavideo-tek.com for answers to common questions, support requests or contact your local office below. Datavideo Corporation (USA) 12300-U East Washington Blvd., Whittier, CA 90606 USA Tel: +1 562 696 2324 contactus@datavideo.us www.datavideo.