DATECS Linea Pro 5 Industrial User Manual
1 DATECS LINEAPRO 5 INDUSTRIAL USER MANUAL LEGAL NOTICE THE INFORMATION IN THIS DOCUMENT CANNOT BE REPRODUCED IN ANY MECHANICAL, ELECTRICAL OR ELECTRONIC WAY AND UNDER ANY CIRCUMSTANCES WITHOUT THE WRITTEN CONSENT FROM DATECS LTD. Address: 4 Datecs Street, Sofia 1592, Bulgaria Phone: +359 2 816 55 50 Fax: +359 2 816 55 65 E-mail: export@datecs.bg UM 07.01.19/v1.0.
1 DATECS LINEAPRO 5 INDUSTRIAL USER MANUAL REVISION HISTORY Version Date Change description 1.0.0 09.04.2020 First Release 2.0.0 26.10.2020 Added section “Regulatory” UM 07.01.19/v1.0.
1 DATECS LINEAPRO 5 INDUSTRIAL USER MANUAL CONTENTS REGULATORY ........................................................................................................................................................................... 5 TECHNICAL SPECIFICATIONS ................................................................................................................................................... 6 GENERAL VIEW ....................................................................................
1 DATECS LINEAPRO 5 INDUSTRIAL USER MANUAL REGULATORY FCC ID: YRW-LINEAPRO5I This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
1 DATECS LINEAPRO 5 INDUSTRIAL USER MANUAL TECHNICAL SPECIFICATIONS Keyboard and Buttons Contactless Card Reader (optional) 2D Barcode Reader Supported 1D and 2D Symbology Connectivity Device Compatibility Audio Features Power Supply Battery Dimension W x H x D, mm Certifications Weight, g Operational temperature range Storage temperature range Compatible Accessories Two Scan buttons Battery status button Reset device button Supports: ISO/IEC 14443 Type-A/MIFARE - MIFARE MINI - MIFARE CLASSIC-1K, MI
1 DATECS LINEAPRO 5 INDUSTRIAL USER MANUAL Use only original equipped DATECS cable USB-A to USB-C (Z05C000000-05) or approved USB-C to USB-C cable for charging Apple device. Use only approved USB adapters. The minimum requirements of USB adapter is 5V/2.1A! Waste Electrical & Electronic Equipment The symbol means that according to local laws and regulations your product shall be disposed of separately from household waste at the end of its working life.
1 DATECS LINEAPRO 5 INDUSTRIAL USER MANUAL GENERAL VIEW UM 07.01.19/v1.0.
1 DATECS 1. Barcode engine 2. Back Cover 3. Right scan button 4. USB type-C connector 5. Left scan button UM 07.01.19/v1.0.0 LINEAPRO 5 INDUSTRIAL USER MANUAL 6. Volume buttons of Apple device 7. On/Off button of Apple device 8. Linea battery cover lock/unlock lever 9. Battery cover 10.
1 DATECS LINEAPRO 5 INDUSTRIAL USER MANUAL GETTING STARTED LineaPro 5 Industrial has rechargeable Li-ion battery. Can be charge from USB port or External features connector. Power source can be variable from USB wall adapters, Datecs power stations … Before first use, battery must be fully charged. If the device is fully discharged, charging time to fully charged would be approx. 4 hours and 30min (for more details please refer to the table below).
1 DATECS LINEAPRO 5 INDUSTRIAL USER MANUAL ATTACHING APPLE DEVICE TO LINEAPRO 5 INDUSTRIAL First is need to be removed back cover. Then must be slide down iPhone to Linea Pro 5 Industrial lightning connector. UM 07.01.19/v1.0.
1 DATECS LINEAPRO 5 INDUSTRIAL USER MANUAL Slide until completely fit of the iPhone to LineaPro 5 Industrial. Place back cover to LineaPro 5 Industrial. UM 07.01.19/v1.0.
1 DATECS LINEAPRO 5 INDUSTRIAL USER MANUAL REPLACING BATTERY OF LINEAPRO 5 INDUSTRIAL The rechargeable battery of Linea can be replaced. Put the lever (1) to unlock position, then pull up the battery cover (2). Remove old battery with pulling up. UM 07.01.19/v1.0.
1 DATECS LINEAPRO 5 INDUSTRIAL USER MANUAL Insert first the side with contacting pads of the battery then press it down. Direction of battery cover closing. Place the clips to correct position. When the battery cover is completely closed, slide the lever to lock position. Replace battery only with new original battery with part number PL-15-110. UM 07.01.19/v1.0.
1 DATECS LINEAPRO 5 INDUSTRIAL USER MANUAL OPERATION MODES For start operating with LineaPro 5 Industrial is need to be attached Apple device and installed application for iOS. For downloading the latest SDK please contact with your distributor. For turn On LineaPro 5 Industrial press one of the scan buttons and unlock Apple device screen. Scanning barcodes LineaPro 5 Industrial can scan 1D and 2D barcodes. To scan barcode first, activate the scanner (by pressing and holding the scan button).
1 DATECS LINEAPRO 5 INDUSTRIAL USER MANUAL Contactless cards reading The LineaPro 5 Industrial has a contactless card reader. Contactless card reader is located on the bottom side. Contactless card, tag or etc… must be placed over the RF ID logo (showed on the picture below). UM 07.01.19/v1.0.
1 DATECS LINEAPRO 5 INDUSTRIAL USER MANUAL Turn off device function When is pressed this turn off, LineaPro 5 Industrial is going to sleep mode immediately. Charging Apple device LineaPro 5 Industrial can charge Apple device, when power source (USB adapter) is attached to USB connector or LineaPro 5 Industrial is placed on Datecs charging station. Charging Apple device can be at LOW and HIGH power and depends on the battery charging state and power source.
1 DATECS LINEAPRO 5 INDUSTRIAL USER MANUAL CARE, MAINTENANCE AND WARRANTY • • • Keep the LineaPro 5 Industrial side of the reach of small children. Do not drop or knock LineaPro 5 Industrial Don’t charge LineaPro 5 Industrial when inside of USB connector is spilled liquid. Please first clean and dry the USB connector and then charge the device. • Do not open the LineaPro 5 Industrial. Only qualified personnel can open the device and make repair.
