DATECS LineaPro 7 Industrial User Manual
1 DATECS LINEAPRO 7 INDUSTRIAL USER MANUAL LEGAL NOTICE THE INFORMATION IN THIS DOCUMENT CANNOT BE REPRODUCED IN ANY MECHANICAL, ELECTRICAL OR ELECTRONIC WAY AND UNDER ANY CIRCUMSTANCES WITHOUT THE WRITTEN CONSENT FROM DATECS LTD. Address: 4 Datecs Street, Sofia 1592, Bulgaria Phone: +359 2 816 55 50 Fax: +359 2 816 55 65 E-mail: export@datecs.bg UM 07.01.12/v1.0.
1 DATECS LINEAPRO 7 INDUSTRIAL USER MANUAL REVISION HISTORY Version Data Change description 1.0.0 14.12.2017 First Release 2.0.0 10.03.2020 Added Section “Regulatory” UM 07.01.12/v1.0.
1 DATECS LINEAPRO 7 INDUSTRIAL USER MANUAL CONTENTS REGULATORY ........................................................................................................................................................................... 5 TECHNICAL SPECIFICATIONS ................................................................................................................................................... 6 GENERAL VIEW ....................................................................................
1 DATECS LINEAPRO 7 INDUSTRIAL USER MANUAL REGULATORY FCC ID: YRW-LINEAPRO7I This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause NOTE 1: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
1 DATECS LINEAPRO 7 INDUSTRIAL USER MANUAL TECHNICAL SPECIFICATIONS Keyboard and Buttons Contactless Card Reader (optional) 2D Barcode Reader Supported 1D and 2D Symbology* Connectivity Device Compatibility Audio Features Power Supply Battery Certificates Dimension W x H x D, mm Weight, g Operational temperature range Storage temperature range Compatible Accessories Two Scan buttons Reset device button Supports: ISO/IEC 14443 Type-A/MIFARE - MIFARE MINI - MIFARE CLASSIC-1K, MIFARE CLASSIC-4K - MIFA
1 DATECS LINEAPRO 7 INDUSTRIAL USER MANUAL Use only original equipped DATECS cable USB-A to USB-C (Z05C000000-05) for charging Apple device. Use only UL approved USB adapters. The minimum requirements of USB adapter is 5V/2.1A! Waste Electrical & Electronic Equipment The symbol means that according to local laws and regulations your product shall be disposed of separately from household waste at the end of its working life.
1 DATECS LINEAPRO 7 INDUSTRIAL USER MANUAL GENERAL VIEW UM 07.01.12/v1.0.
1 DATECS 1. Barcode engine 2. Back Cover 3. On/Off button of Apple device 4. Left and Right scan buttons 5. USB type-C connector 6. Volume buttons of Apple device UM 07.01.12/v1.0.0 LINEAPRO 7 INDUSTRIAL USER MANUAL 7. Opening for 8. Linea battery cover lock/unlock lever 9. Battery cover 10.
1 DATECS LINEAPRO 7 INDUSTRIAL USER MANUAL GETTING STARTED LineaPro 7 Industrial has rechargeable Li-ion battery. Can be charge from USB port or External features connector. Before first use, battery must be fully charged. If the device is fully discharged, charging time to fully charged would be approx. 4 hours and 30min. Depends of the settings, LineaPro 7 Industrial can pass-through input power supply from USB connector or External features connector to Apple device.
1 DATECS LINEAPRO 7 INDUSTRIAL USER MANUAL ATTACHING APPLE DEVICE TO LINEAPRO 7 INDUSTRIAL First is need to be removed back cover. Then must be slide down iPhone to Linea Pro 7 Industrial lightning connector. UM 07.01.12/v1.0.
1 DATECS LINEAPRO 7 INDUSTRIAL USER MANUAL Slide until completely fit of the iPhone to LineaPro 7 Industrial. Place back cover to LineaPro 7. UM 07.01.12/v1.0.
1 DATECS LINEAPRO 7 INDUSTRIAL USER MANUAL REPLACING BATTERY OF LINEAPRO 7 INDUSTRIAL The rechargeable battery of Linea can be replaced. Put the lever (1) to unlock position, then pull up the battery cover (2). 1 2 Remove old battery with pulling up. UM 07.01.12/v1.0.
1 DATECS LINEAPRO 7 INDUSTRIAL USER MANUAL Insert first the side with contacting pads of the battery then press it down. Direction of battery cover closing. Place the clips to correct position. When the battery cover is completely closed, slide the lever to lock position. Replace battery only with new original battery with part number PL-15-110. UM 07.01.12/v1.0.
1 DATECS LINEAPRO 7 INDUSTRIAL USER MANUAL OPERATION MODES For start operating with LineaPro 7 Industrial is need to be attached Apple device and installed application for iOS. For downloading the latest SDK please contact with your distributor. For turn On LineaPro 7 Industrial press one of the scan buttons and unlock Apple device screen. Scanning barcodes LineaPro 7 Industrial can scan 1D and 2D barcodes. To scan barcode first, activate the scanner (by pressing and holding the scan button).
1 DATECS LINEAPRO 7 INDUSTRIAL USER MANUAL Contactless cards reading The LineaPro 7 Industrial has a contactless card reader. Contactless card reader is located on the bottom side. Contactless card, tag or etc… must be placed over the RF ID logo (showed on the picture below). UM 07.01.12/v1.0.
1 DATECS LINEAPRO 7 INDUSTRIAL USER MANUAL Transferring data between Apple device and PC or MAC LineaPro 7 Industrial is supporting sync function when USB cable is plugged. Sync can be enable or disabled by setting. If “pass-through sync”, was disabled, when USB cable is plugged to LineaPro 7 Industrial will be charge only. To enter in sync mode can be used this way: Holding scan button and plug the USB cable. After that scan button must be release.
1 DATECS LINEAPRO 7 INDUSTRIAL USER MANUAL CARE, MAINTENANCE AND WARRANTY • • Keep the LineaPro 7 Industrial side of the reach of small children. Do not drop or knock LineaPro 7 Industrial • Do not open the LineaPro 7 Industrial. Only qualified personnel can open the device and make repair. If the LineaPro 7 Industrial is not working, please contact with your dealer.