User guide

ManualsBrandsDavey ManualsWater equipmentHurricane Turbo Swim Jet

COUNTER-CURRENT SWIMMING

Hurricane Turbo Swim Jet

INSTALLATION INSTRUCTIONS

PACKET NO.1

With a COUNTER-CURRENT SWIMMING device your swimming pool is no longer a simple

man-made lake. It becomes the most appealing place to be, an amusement park, a place to

have fun and become fit.

A COUNTER-CURRENT SWIMMING device transforms your swimming pool into a water

torrent and gives you general and localized hydrotherapeutic massages.

The high-powered pump of the COUNTER-CURRENT SWIMMING device pumps up water from

the pool and pushes the water back into the pool forcefully, together with millions of air bubbles

which optimise your massages.

Summary of content (8 pages)

PAGE 1
COUNTER-CURRENT SWIMMING Hurricane Turbo Swim Jet INSTALLATION INSTRUCTIONS PACKET NO.1 With a COUNTER-CURRENT SWIMMING device your swimming pool is no longer a simple man-made lake. It becomes the most appealing place to be, an amusement park, a place to have fun and become fit. A COUNTER-CURRENT SWIMMING device transforms your swimming pool into a water torrent and gives you general and localized hydrotherapeutic massages.
PAGE 2
FIBREGLASS/VINYL CUT-OUT OF THE PANEL: Place the pattern on the inside panel taking the 400 mm linear dimension between the axis XY and the top of the structure into account. Caution: Make sure you position axis XY parallel to the top of the structure. Mark the 14 mounting bolt holes on the panel and cut out the pattern according to the points. Trace the profile on the panel and carry out the cutting and drilling.
PAGE 3
CONCRETE DRILLING: Position the pattern on the inside casing taking the 400 mm linear dimension between the axis XY and the top of the structure into account. CAUTION: Make sure you position axis XY parallel to the top of the structure. Pierce the 2 mounting bolt holes of 6 mm diameter in A and B. MOUNTING OF PACKAGE 1 ON THE JET BODY: 1. Placing of the self-adhesive Gasket: Clean the pre-drilled side of the Counter Flange (2) then stick Gasket (4) to Counter Flange. 2.
PAGE 4
LOCATION OF THE PRESSURE REGULATOR: If your electrical equipment box is more than 5 metres away from the front face, you should bring the pressure regulator (interrupter of the pneumatic button) close to the swimming pool in a connection box. POSITIONING OF THE PUMP: The pump of this device must be installed next to the structure and must be connected by a pressure pipe, minimum diameter 50mm.
PAGE 5
Hurricane Turbo Swim Jet INSTALLATION INSTRUCTIONS PACKET NO.2 With the HURRICANE TURBO SWIM JET your swimming pool is no longer a simple man-made lake. It becomes the most appealing place to be, an amusement park, a place to have fun and become fit. The SWIM JET transforms your swimming pool into a water torrent and gives you general and localized hydrotherapeutic massages, as well making counter-current swimming possible.
PAGE 6
MOUNTING OF PACKAGES 2, 3, 4 - Make sure the 12 screws of the flange are correctly fastened without using excessive force. - Cut out the liner along the inside of the flange by using a cutter. - Remove the protective shield attached to the Jet Body with three M5 screws length 10. CONNECTING: -Connect the small capillary tube to the back of the Control Button, and pass it under the air intake pipe, then through the slit foreseen for this purpose on the Air Regulation Button.
PAGE 7
CONNECTION TO THE SWITCH BOX POSITIONING OF THE PRESSURE REGULATOR: If your electrical equipment box is more than 5 metres away from the Jet Face, the Pressure Regulator (interrupter of the pneumatic button) should be moved closer to the swimming pool in a connection box. WINTER STORAGE: (Only required in countries with temperatures below 0 degrees Celcius) -Disconnect the capillary tube from the switch box. -Dismantle the Jet Face and remove the whole device.
PAGE 8
Swim Jet -The push-button is used to turn on the device by applying light pressure to the button. -The other button is used to regulate the output of air from the valve, allowing more or less air to be propelled from the valve. -CAUTION: Do not forget to close this air button after having used the massage pipe which is fitted on the valve (optional accessory).