Daytime Fan-Aspirated Radiation Shield Kit Installation Manual For Vantage Pro2™ & Vantage Pro2 Plus™ Stations Introduction The instructions describe how to upgrade a non-aspirated Vantage Pro2 radiation shield to a Daytime Fan-Aspirated Radiation Shield. The upgrade kit can be installed on any Vantage Pro2 or Vantage Pro2 Plus Integrated Sensor Suite (ISS) equipped with a non-aspirated radiation shield.
Installing the Daytime Fan Kit The kit also includes the following hardware: #8-32 x 3-1/4" Screws (3) #8 Split-Lock Washers (6) #8-32 x 1/2" Screws (3) Threaded Spacers (3) #8 Flat Washers (6) 12" Cable Ties (2) Daytime Fan Kit Hardware Tools Needed You may need some or all of the following tools to complete the upgrade: • A medium Phillips-Head screwdriver • A medium slot-tip screwdriver • Other tools as required to remove and re-mount the ISS Installing the Daytime Fan Kit Installation Overview T
Installing the Daytime Fan Kit To put your console in Setup Mode: At your Vantage Pro2 console, press and hold DONE and then press the down arrow (-) to put the console in Setup Mode. This prevents the reception of erroneous data while you are removing the ISS. Note: If the console acquires erroneous data during the upgrade, see Take the Console Out of Setup Mode on page 16 for instructions on clearing data. Additional information on clearing console data can be found in the Vantage Pro2 Console Manual.
Installing the Daytime Fan Kit 3. Remove the rain collector cone from the ISS base by rotating the cone counter-clockwise. When the cone’s latches line up with openings in the base, you can lift the cone off. The cone fits in the base tightly and may require extra pressure to remove the first few times. Steady the ISS base between your knees when removing the cone Twist to Open Remove the Rain Collector Cone 4. Remove the three 8-32 x 4'' screws holding the radiation shield plates together. 5.
Installing the Daytime Fan Kit Check Temperature/Humidity Sensor Orientation The orientation and placement of the Temperature/Humidity sensor should be checked, and in many cases, should be reoriented. There are three ways the sensor could be mounted in an ISS: • On the second to bottom-most plate of radiation plating stack with the Temperature/Humidity sensor facing up. • Underneath the top plate of the radiation plating stack, on the insulating disk with the Temperature/Humidity sensor facing down.
Installing the Daytime Fan Kit 3. Reinstall the sensor face down on the radiation plate, using the two 1' spacers and #4 screws included with the kit. 4. Put the cable clamp back on the cable and use the screw and flat washer to resecure the cable onto the radiation plate. 5. Replace the radiation plate back in its correct place in the radiation shield plating stack.
Installing the Daytime Fan Kit 5. Put the cable clamp back on the cable and use the screw and flat washer to resecure the cable onto the radiation plate. 6. Replace the radiation plate back in its correct place in the radiation shield plating stack.
Installing the Daytime Fan Kit 6. Run the Temperature/Humidity cable through the top of the three open plates. 4" Screws Lock Washer Flat Washer Fan Plate Temperature/ Humidity Cable New Open Plate Plates Reassemble the radiation shield plates with the fan plate 7. Set aside the re-assembled radiation shielding and find the fan plate motor assembly.
Installing the Daytime Fan Kit 8. Attach the three threaded spacers to the fan plate using the three #8-32 x 1/2'' screws and the three #8 washers and #8 lock washers included with the kit. Threaded Spacer (3) Fan Plate #8 Flat Washer #8 Split-Lock Washer #8-32 x 1/2" Screw Install Threaded Spacers 9. Detach the fan motor cable from the power cable assembly on the fan plate and set the fan motor aside. Fan Motor Assembly Fan Plate Fan Plug Power Cable Assembly Detach Fan Motor Cable 10.
Installing the Daytime Fan Kit 11. Bring the Temperature/Humidity cable over the top of the fan plate so that no slack in the cable exists between the sensor and the fan plate and press it firmly into the cable channel on the fan plate.
Installing the Daytime Fan Kit 12. Place one of the 4'' screws removed from the original radiation shield and its corresponding #8 lock washer and # 8 flat washer into one #8-32 x 4" Screws (3) of the radiation shield plate holes on the fan plate located #8 Lock Washer just #8 Flat Washer counter-clockwise from a threaded spacer, making sure the screw goes through the boss in each of the plates and lines up with the threaded insert located in the Fan Plate bottom plate. 13.
Installing the Daytime Fan Kit 20.
Installing the Daytime Fan Kit Insert front screw 21. Lower the ISS base first onto the stack so that #8-32 x3-1/4" Screws (3) the screw goes into the boss. Turn the screw a #8 Lock Washers #8 Flat Washers few times to engage the threads. 22. Place a lock washer and flat washer on the SIM Housing other two 3 1/4'' screws then insert them through the other two screw holes. 23. Tighten all three ISS Base screws to securely fasten the radiation shield to the ISS base.
Installing the Daytime Fan Kit 9. Connect the wire coming from the top solar panel on the SIM cover included in the components of the fan-aspirated unit to the SIM board. Note: This wire is not needed on cabled Vantage Pro2. For cabled systems, you should secure it where it will not interfere with the SIM box. Top Panel Wire Sensor Interface Module (SIM) SIM Cover Bottom Panel Wire Temperature/ Humidity Cable Power Cable Assembly Connecting the Solar Panel Wires 10.
Maintenance Take the Console Out of Setup Mode 1. At your Vantage Pro2 console, press and hold DONE for three seconds to take the console out of Setup Mode. 2. Check the console for erroneous rain data and clear if necessary. To clear erroneous daily rain data: • Select the RAINDAY button. The graph icon displays next to the daily rain variable. • Press and release 2ND, then immediately press and hold CLEAR. • The daily rain variable will start blinking.
Contacting Davis Technical Support If you are experiencing problems performing the upgrade or have problems with your Daytime Fan-Aspirated Radiation Shield, first be sure to check all cable connections. If you are unable to solve the problem, please call Davis Technical Support. We’ll be glad to help. Most questions can be answered over the phone. You can also email us for support or visit our website. Sorry, we are unable to accept collect calls.