User guide

ManualsBrandsDaystar ManualsCarKU70033BK

TOOLS NEEDED

• Floor jack

• Jack stand (s) 4

• Wheel chock

• Grease ( poly lube gun KU11005)

• 3/4 drive ratchet

• 10” 3/4 extension

• 5/8 wrench and 5/8 socket

• Measuring tap

• 18mm wrench

• 18mm socket

BILL OF MATERIALS

Part # Description Qty

S11098

Upper arm 2

S11117

Rod end 2

BU70033

Hardware kit 1

M03856

Bushing 8

S11118

Sleeve 2

S10205

9/16 Nut 2

S10212

9/16 Bolt 4

S10818

1-14 Jam nut 2

S10903

washer 8

S10818

1-14 Jam nut 2

P11183

Thread lock 1

S11123

Nut plate 2

Jeep JK Products

• KJ09138 3/4” Front & rear lift

• KJ09137 1 3/4” Front & rear lift

• KU09059 EVS Foam bump-stops

• KU09060 EVS Foam bump-stops

• KU70034 Ft lower control arms

• KU70033 Rear upper control arms

• KU70037 Rear lower control arms

• KU70091 poly flex tool

• KU11005 Poly lube gun

• KJ71020 Upper dash panel

• KJ71020 Lower switch panel

KU70033 Rear upper

2007 to Current Jeep JK control arm kit

www.Daystarproducts.com

Tech Support Contact Info

Tech@DaystarWeb.com

Phone: 623.907.0081

Fax: 623.907.0088

841 South 71

Avenue

Instruction Sheet P11241

2007 Daystar Products International Inc.

Hells gate, Moab UT

Summary of content (4 pages)

PAGE 1
TOOLS NEEDED BILL OF MATERIALS Part # • • • • • • • • • • Floor jack Jack stand (s) 4 Wheel chock Grease ( poly lube gun KU11005) 3/4 drive ratchet 10” 3/4 extension 5/8 wrench and 5/8 socket Measuring tap 18mm wrench 18mm socket Jeep JK Products • • • • • • • • • • • KJ09138 3/4” Front & rear lift KJ09137 1 3/4” Front & rear lift KU09059 EVS Foam bump-stops KU09060 EVS Foam bump-stops KU70034 Ft lower control arms KU70033 Rear upper control arms KU70037 Rear lower control arms KU70091 poly flex tool K
PAGE 2
Thank you for choosing Daystar Products 12. With the Daystar control arm installed tighten the mount bolts to 75 ft pounds and jam nuts. Daystar recommends a certified technician install this system. In addition to these instruction, professional knowledge of disassemble/reassembly procedures as well as post instructions checks must be known. Attempts to install this system without this knowledge and expertise may jeopardize the integrity and/or operating of the vehicle.
PAGE 3
Control arm assemble instructions 9. Check the length of the Daystar upper control arm. 10. Install the control arm in the frame side first, using the supplied bolt and nut plate. Do not tighten the bolt yet. Note ( The bend go’s to the inside). 1. Lay out the control arms on a clean work service. 2. Lube the bushing, sleeve’s and then install them into the upper control arm. S11098 M03856 S11118 3. Lube the bushing and steel tubing and install them into the threaded rod end and install jam nut.
PAGE 4
Control arm assembling steps 4. Installation steps 6. Block the front wheels and jack up the rear axle so you can remove the rear wheel. With wheel removed place a jack stand under the rear axle. 7. With the Jeep setting on the jack stands, remove the upper control arm bolts with a 18mm wrench and socket. 8. Remove the upper control arm. Install the control arm and rod in together. 5. With the control arm assembled, set the length of the arm by turning the rod end in or out .