Operating instructions

ManualsBrandsDayton ManualsElectric Heater3VE49D

Form 5SXXXX

Printed in U.S.A.

XXXXX

XXXX/XXX/XXXX

XXXXXX

XX/XX

Table of Contents Page

Description . . . . . . . . . . . . . . . . . . . . . . . 1

Specifications . . . . . . . . . . . . . . . . . . . . . 1

Introduction . . . . . . . . . . . . . . . . . . . . . . 1

Unpacking . . . . . . . . . . . . . . . . . . . . . . . 1

Product Features . . . . . . . . . . . . . . . . . . 2

General Safety Information . . . . . . . . 2-3

Assembly . . . . . . . . . . . . . . . . . . . . . . . 4-5

Operation . . . . . . . . . . . . . . . . . . . . . . 5-8

Kerosene (1-K or

Number 1 Fuel Oil) . . . . . . . . . . . . . . 5-6

Overview of Heater Design. . . . . . . . . 6

Fueling Your Heater . . . . . . . . . . . . . . 6

Ventilation . . . . . . . . . . . . . . . . . . . . . . 7

Long-Term Storage . . . . . . . . . . . . . 7-8

Maintenance . . . . . . . . . . . . . . . . . . . 8-12

Replacing Fuse . . . . . . . . . . . . . . . . . . . 12

Wiring Diagrams . . . . . . . . . . . . . . . . . 13

Repair Parts Illustration Models

3VE48D, 3VE49D, 3VE50E, 3VE51E . . . 14

Repair Parts List Models

3VE48D, 3VE49D, 3VE50E, 3VE51E . . 14-15

Repair Parts Illustration Model

3VE52E . . . . . . . . . . . . . . . . . . . . . . . . . 16

Repair Parts List Model 3VE52E . . . . . 17

Repair Parts List, Wheels and

Handles . . . . . . . . . . . . . . . . . . . . . . . . . 18

Troubleshooting Chart . . . . . . . . . . . . 19

Warranty Information . . . . . . . . . . . . . 20

Introduction

Please read this USER’S MANUAL

carefully. It will show you how to

assemble, maintain and operate this

heater safely and efficiently to obtain

the full benefits of its many features.

Consumer: Retain these instructions

for future reference.

Unpacking

1. Remove all packing items applied to

heater for shipment.

2. Remove all items from carton.

3. Check all items for shipping damage. If

heater is damaged, promptly inform

dealer where you purchased heater.

Dayton

Portable

Oil-Fired Heaters

Operating Instructions & Parts Manual 3VE48D, 3VE49D, 3VE50E, 3VE51E and 3VE52E

Please read and save these instructions. Read carefully before attempting to assemble, install, operate or maintain the product described.

Protect yourself and others by observing all safety information. Failure to comply with instructions could result in personal injury and/or

property damage! Retain instructions for future reference.

Description

Dayton Models 3VE48D, 3VE49D, 3VE50E, 3VE51E and 3VE52E heaters are 45,000 to

210,000 BTU/Hr heaters. These heaters use 1-K Kerosene (see Operation section

for alternative fuels) for combustion, and electricity to run the fan. It is primarily

intended for temporary heating of well ventilated buildings under construction,

alteration, or repair. This heater may be used in agricultural, industrial and com-

mercial environments.

Figure 1 – Models 3VE48D and 3VE49D

Figure 2 – Models 3VE50E, 3VE51E and

3VE52E

Specifications

ELECTRICAL SPECIFICATIONS

Electrical

Model Input Amperage Fuse Spark Plug Gap

3VE48D 120V, 60 Hz 1.6 125V/8 amp .140” (3.5mm)

3VE49D 120V, 60 Hz 1.6 125V/8 amp .140” (3.5mm)

3VE50E 120V, 60 Hz 2.5 125V/8 amp .140” (3.5mm)

3VE51E 120V, 60 Hz 3.2 125V/8 amp .140” (3.5mm)

3VE52E 120V, 60 Hz 3.7 125V/8 amp .140” (3.5mm)

GENERAL SPECIFICATIONS

thgieWeziSleuFknaT leuFpmuPfo epyT

Model Fuel Input Rating Pressure Capacity Consumption L x W x H (Inches) Lbs. (kg)

3VE48D 1-K Kerosene 45,000 BTU/Hr 2.8 PSI 5.0 Gallons .35 Gal/Hr 32 x 11

/4 x 16

/4 26.9 (12.2)

3VE49D 1-K Kerosene 75,000 BTU/Hr 3.8 PSI 5.0 Gallons .57 Gal/Hr 32 x 11

/4 x 16

/4 26.9 (12.2)

3VE50E 1-K Kerosene 125,000 BTU/Hr 5.5 PSI 10.0 Gallons .95 Gal/Hr 36

/10x 21

/2 x 24

/10 53.6 (24.3)

3VE51E 1-K Kerosene 170,000 BTU/Hr 6.5 PSI 13.0 Gallons 1.3 Gal/Hr 41

/10x 23

/10 x 26

/10

/10x 23

/10 x 26

/10

59.5 (27.0)

3VE52E 1-K Kerosene 210,000 BTU/Hr 8.5 PSI 13.0 Gallons 1.6 Gal/Hr 41 61.7 (28.0)

Summary of content (20 pages)

PAGE 1
3VE48D, 3VE49D, 3VE50E, 3VE51E and 3VE52E Operating Instructions & Parts Manual Please read and save these instructions. Read carefully before attempting to assemble, install, operate or maintain the product described. Protect yourself and others by observing all safety information. Failure to comply with instructions could result in personal injury and/or property damage! Retain instructions for future reference.
PAGE 2
3VE48D, 3VE49D, 3VE50E, 3VE51E and 3VE52E Dayton Operating Instructions and Parts Manual Dayton Portable Oil-Fired Heaters ® E N G L I S H Dimensions 16¾" H 11¾" 32" Models 3VE48C and 3VE49C L 3VE50E 3VE51E 3VE52E H 24 6 /10” 26 1 /10” L 36 /10” 41 8 /10” W 21 /2“ 231/32” 1 1 W Models 3VE50D, 3VE51D and 3VE52D Figure 3 – Heater Dimensions Product Features Electric Outlet Handle Front Hot Air Outlet Fan Guard Upper Shell Hot Air Outlet Upper Shell Handle Pressure Gauge Lower Sh
PAGE 3
Dayton Operating Instructions and Parts Manual Models 3VE48D, 3VE49D, 3VE50E, 3VE51E and 3VE52E General Safety Information (Continued) However, #1 or #2 fuel oil (diesel fuel) may also be used if 1-K kerosene is not available. Be advised that these fuels do not burn as clean as 1-K kerosene, and care should be taken to provide more fresh air ventilation to accommodate any added contaminants that may be added to the heated space. Use of #1 or #2 fuel oil may result in more periodic maintenance.
PAGE 4
3VE48D, 3VE49D, 3VE50E, 3VE51E and 3VE52E Dayton Operating Instructions and Parts Manual Dayton Portable Oil-Fired Heaters ® E N G L I S H Assembly Model 3VE48D, 3VE49D 3VE50E 3VE51E 3VE52E Wheel Support Frame No Yes Yes Yes Wheels No Yes Yes Yes Front-Handle No Yes Yes Yes Rear-Handle No Yes Yes Yes Threaded Axle No Yes Yes Yes Handle Yes No No No Cord Wrap Yes Yes Yes Yes Hardware Kit: HW-KFA1001 Yes No No No Hardware Kit: HW-KFA1016 No Yes Yes Yes 3VE
PAGE 5
Dayton Operating Instructions and Parts Manual Models 3VE48D, 3VE49D, 3VE50E, 3VE51E and 3VE52E Assembly (Continued) Screw FOR MODELS 3VE48D AND 3VE49D ONLY TOOLS REQUIRED - Medium Phillips screwdriver. 1. Lift front guard for arrow direction and make sure that guard’s wedged portion fits into the slit hole on the upper housing. 2. Align the holes in upper housing with two mounting holes on the handle as shown in Figure 7. 3. Secure handle with screws provided. 4.
PAGE 6
Dayton Operating Instructions and Parts Manual 3VE48D, 3VE49D, 3VE50E, 3VE51E and 3VE52E Dayton Portable Oil-Fired Heaters ® E N G L I S H Operation (Continued) that these fuels do not burn as clean as 1-K kerosene, and care should be taken to provide more fresh air ventilation to accommodate any added contaminants that may be added to the heated space. NOTE: Kerosene should only be stored in a blue container that is clearly marked “kerosene”. Never store kerosene in a red container.
PAGE 7
Dayton Operating Instructions and Parts Manual Models 3VE48D, 3VE49D, 3VE50E, 3VE51E and 3VE52E Operation (Continued) VENTILATION Risk of indoor air pollution. Use heater only in well ventilated areas. CAUTION Provide a fresh air opening of at least three (3) square feet (2,800 sq. cm) for each 100,000 BTU/Hr. rating. Provide extra fresh air if more heaters are being used. Example: A 3VE52E heater requires one of the following : 1. A two-car garage door raised six inches (15.24 cm). 2.
PAGE 8
Dayton Operating Instructions and Parts Manual 3VE48D, 3VE49D, 3VE50E, 3VE51E and 3VE52E Dayton Portable Oil-Fired Heaters ® E N G L I S H Maintenance Seal WARNING AIR OUTPUT FILTER, LINT FILTER Never service heater while it is plugged in or while hot! Fuel Drain Bolt Figure 12 - Drain Bolt 6. Store heater in dry well ventilated area. Make sure storage place is free of dust and corrosive fumes. 7.
PAGE 9
Dayton Operating Instructions and Parts Manual Models 3VE48D, 3VE49D, 3VE50E, 3VE51E and 3VE52E Maintenance (Continued) - Place set screw on flat of shaft. - Tighten screw firmly (40-50 inchpounds/4.5-5.6 N-m). Reinstall upper shell. NOZZLE CLEAN NOZZLE AS NEEDED (For Models 3VE48D, 3VE49D, 3VE50E and 3VE51E only) - Remove upper shell (See Air Intake Filter, page 8). - Remove fan blade (See Fan Blades). - Remove fuel and air line hoses from nozzle adaptor. - Remove ignitor wire from spark plug.
PAGE 10
Dayton Operating Instructions and Parts Manual 3VE48D, 3VE49D, 3VE50E, 3VE51E and 3VE52E Dayton Portable Oil-Fired Heaters ® Maintenance (Continued) PHOTOCELL - Reinstall spark plug to nozzle adaptor. - Attach ignitor wire to spark plug. - Reinstall fan and upper shell. CLEAN PHOTOCELL ANNUALLY OR AS NEEDED. Screw Spark Plug Ignitor Wire Nozzle Adaptor GAP Spark Plug Figure 18 – Spark Plug Replacement (For Model 3VE52E only) - Remove upper shell (See Air Intake Filter, page 8).
PAGE 11
Dayton Operating Instructions and Parts Manual Models 3VE48D, 3VE49D, 3VE50E, 3VE51E and 3VE52E Maintenance (Continued) Fuel Filter - Remove side cover. Fuel Line - Pull fuel line off fuel filter neck. - Turn fuel filter counterclockwise 90 degrees, pull, and remove. Switch Wires - Wash fuel filter with clean fuel and replace in tank. Model Pump Pressure 3VE48D 2.8 PSI 3VE49D 3.8 PSI 3VE50E 5.5 PSI 3VE51E 6.5 PSI 3VE52E 8.5 PSI E N G L I S H - Attach fuel line to fuel filter neck.
PAGE 12
3VE48D, 3VE49D, 3VE50E, 3VE51E and 3VE52E Dayton Operating Instructions and Parts Manual Dayton Portable Oil-Fired Heaters ® E N G L I S H Maintenance (Continued) Fuse Holder REPLACING FUSE NOTE: The heater is fuse protected. If your heater fails to ignite, DO NOT RETURN YOUR HEATER TO THE STORE. Fuse Please follow the simple instructions below to inspect and change the fuse. SHOCK HAZARD. To prevent personal injury, unplug the power cord before replacing fuse.
PAGE 13
Dayton Operating Instructions and Parts Manual Models 3VE48D, 3VE49D, 3VE50E, 3VE51E and 3VE52E Wiring Diagrams CONTROL PCB BLACK SPARK PLUG BLACK CN3 CN4 WHITE IGNITOR BLACK POWER LAMP (LED) ORANGE CN3 CN7 RED BLACK PUMP MOTOR WHITE GREEN THERMOSTAT (TEMP.
PAGE 14
3VE48D, 3VE49D, 3VE50E and 3VE51E Dayton Operating Instructions and Parts Manual For Repair Parts, call 1-800-323-0620 24 hours a day – 365 days a year Please provide following information: -Model number -Serial number (if any) -Part description and number as shown in parts list 46 23-3 23-5 43 42 23-1 23-8 23-7 23-2 23-4 23-6 45 E N G L I S H 19 21 22 26-2 26-5 26-6 26-7 26-9 26-1 26-3 26-4 20 41 23 24 28 27 26 18 17 11 26-11 26-15 26-16 26-17 26-18 26-21 13 26-10 26-12 26-13 26-14 26-2
PAGE 15
Dayton Operating Instructions and Parts Manual Models 3VE48D, 3VE49D, 3VE50E and 3VE51E Repair Parts List for Portable Oil-Fired Heaters (Continued) Reference Number 21 22 23 23-1 23-2 23-3 23-4 23-5 23-6 23-7 23-8 24 25 26 26-1 26-2 26-3 26-4 26-5 26-6 26-7 26-8 26-9 26-10 26-11 26-12 26-13 26-14 26-15 26-16 26-17 26-18 26-19 26-20 26-21 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 Description Screw-BH1 Photocell Assembly Burner Head Assembly Burner Head Nozzle Washer-Nozzle Seal Spring-No
PAGE 16
3VE52E Dayton Operating Instructions and Parts Manual For Repair Parts, call 1-800-323-0620 24 hours a day – 365 days a year Please provide following information: -Model number -Serial number (if any) -Part description and number as shown in parts list 21-8 21-1 40 E N G L I S H 21-3 21-5 21-2 21-7 21-4 43 21-6 17 19 20 21 42 26 25 24 22 18 41 16 15 9 11 12 23 13 14 10 27 28 35 4 30 38 37 36 29 1 24-2 39 3 24-5 24-7 24-9 24-8 24-11 24-15 5 24-1 6 34 33 24-3 7 8 31 24-
PAGE 17
Dayton Operating Instructions and Parts Manual Model 3VE52E Repair Parts List for Portable Oil-Fired Heater (Model 3VE52E) Ref. No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 21-1 21-2 21-3 21-4 21-5 21-6 21-7 21-8 22 23 24 24-1 24-2 24-3 24-4 Description Part No.
PAGE 18
3VE48D, 3VE49D, 3VE50E, 3VE51E and 3VE52E Dayton Operating Instructions and Parts Manual For Repair Parts, call 1-800-323-0620 24 hours a day – 365 days a year Please provide following information: -Model number -Serial number (if any) -Part description and number as shown in parts list 7-1 1 7-2 6 2 E N G L I S H 7-3 3 1 3 7-4 5 2 4 3 7-6 Figure 32 – Repair Parts Illustration for Models 3VE50E, 3VE51E, 3VE52E Figure 31 – Repair Parts Illustration for Models 3VE48D, 3VE49D Replacement Parts List fo
PAGE 19
Dayton Operating Instructions and Parts Manual Models 3VE48D, 3VE49D, 3VE50E, 3VE51E and 3VE52E Troubleshooting Chart Symptom Possible Cause(s) Corrective Action Heater ignites but MAIN PCB assembly shuts heater off after a short period of time. (Indicator Lamp is flickering and room temp. display indicates “E1”) 1. Wrong pump pressure 2. Dirty Air Output, Air Intake or Lint Filter 1. See Pump Pressure Adjustment, page 11 2. See Air Output, Air Intake and Lint Filters, page 8 3.
PAGE 20
Dayton Operating Instructions and Parts Manual 3VE48D, 3VE49D, 3VE50E, 3VE51E and 3VE52E Dayton Portable Oil-Fired Heaters ® E N G L I S H LIMITED WARRANTY DAYTON ONE-YEAR LIMITED WARRANTY. DAYTON® PORTABLE OIL-FIRED HEATERS, MODELS COVERED IN THIS MANUAL, ARE WARRANTED BY DAYTON ELECTRIC MFG. CO. (DAYTON) TO THE ORIGINAL USER AGAINST DEFECTS IN WORKMANSHIP OR MATERIALS UNDER NORMAL USE FOR ONE YEAR AFTER DATE OF PURCHASE.