Pe 1. Introduction 2. Safety instructions 3, Typical installation sequence 4. Selection of the diameter of power cables snd speaker cables 5. Wiring diagrams 6. Connection methods 7. Specifications 8, Possible faults and their solutions 9. Box contents 10. Warranty and maintenance info 11.
ail saliva a Thar yo for purchasing this Deaf Lance product Out company is commuted ta he creation of of extremely aud sound systematization loss of quilt “To ensure proper use, please carefully read through this manual before using this product, its especially Important that you rend and observe caution's in this Manuel. Pleads i anal isi 8 see snd accessible Pe for future reference.
Len nde Use the table below to select the desired diameter based Use the table below So select the desired diameter based ‘on tha length and the current consumption. ‘on the length and the power consumption. 0442233445 5-867 | 78 ) Gdn es xl tr Connect the speaker cables from the positive and negative terminals of the speakers ts the respective outputs of the amplifier terminal marked with CH1/CH2, CH3 / CHA SPEAKERS OUTPUTS, as shown at the diagram.
Lana en ald Et iE tra Step 1, Conn act the speaker cable farm terminal af the amplifier tn terminal of the speaker, Sta 2. Connect the speaker cable from (germinal of the amplifier bo -} terminal af the speaker. Step. Repeat the installation sequence for overstepped 1 snd step 2 wee ff Currant} The minimums permissible connection load Impedance of singe channel Is 1 ohm, For shoplifter the operating voltage bs 5-15V. Standard wiring diagram of four channel amplifier to heat unk ep 1.
1. +12Y — power supply terminal +12 2. REM IN. connector of remote activation of the amplifier 3. GND grounding supply terminal CONNECTION METHODS “Tha minimum permissible load impedance st the output of the amplifier is 1 ohm. lls any case da not expose the amplifier to the loads Jo war than specified by the manufactures. Use these schematics to latest load impedance of different connection types.
_— 4 Ohm 2 Ohm 8 Ohm 4 Ohm Solos cols | Toil impedance 4 Ohm 1.33 Ohm 8 Ohm 2.66 Chm EEE 4 Ohm 1 Ohm & Chm 2 Ohm | TR Leastwise | Continuance 3 4 Ohm 4 Ohm 8 Ohm 8 Ohm CAUTION High sours pressures san damage your halt Lassa uss the common sense wain controlling volume SUPERMOM WIRING SEAGRAM The minimum permissible load impedance at the single channel is 1 ohm, in bridged mote 2 chm. Use these formulas to calculate the load impedance of various types of connections.
Le date EN Total impedance Dubious OSub2+ D8ub3... SCHEMES (RF ENABLING THE LOAD QF THE SUB WOOFER i any case do not expose the amplifier to the loads lower than specified by the manufacturer. Use these schematics to calculate load impedance of different inaction types. Le TH 141 242 444 The sub woofer has voice coll woofer coils in i ine 1+1 Chum 2 Ohm 2+2 Ohm 4 Ohm 4+4 Ohm 8 Ohm Bald Wee lag dg a oe Eas EET +1 Ohm 4.
EEE 1+1 Ohm 0.66 Ohm 2+2 Ohm 1.33 Ohm A+4 Ohm 2.66 Ohm rear 1+1 Ohm 8.5 Ohm 2+2 Chm 1 Chm 4+4 Ohm 2 Chm res 1+1 Ohm 8.25 Ohm 2+2 Ohm 0.5 Ohm 4+4 Ohm 1 Ohm Rene 1+1 Ohm 0.16 Ohm 2+2 Ohm ©.33 Ohm 4+4 Chm 0.66 Ohm pm 141 Ohm ©.125 Ohm 2+2 Chm 0.25 Ohm 4+4 Ohm 8.
Bane aie ges i! Model AAP-S804D Power RFS 4 Ohm™ J) 14ax4 Power RMS 2 Ohen® (43 2854 Power RMS 1 lm (9) 430n 4 Power RMS 4 Ohm* bridged mode (W) F162 Rowe RIS 2 Oho bridged mods (W) 833x2 High puss filter (H2} 15-6900 Bow pass filter (Ha) 50-6000 Crossover (dB / Oct} 12 Baas level adjustment #-12 Piquancy respond (Hz) 10-20 000 Input sensitivity 04) 02-8 Signal 0 notes ratio (48) 00 Damping factor 250 Input terminal connection (AWG J men?) ayah Output inseminate connection (AWS / mm’) 8/837 Working voltage
SH Fags he EN 1. Amplifier pe. 2 Owner's Manual Warranty card —1 pe 4, Mounting i Gt-1 5 Window decals 2pe. Lady ba Te gn Eee ae Dea Banks products are warranted against defects concerning materials and their manufacturing under moral functioning conditions.
