INSTALLATION INSTRUCTIONS DishDrawerTM dishwasher DD24DUT7 and DD24DVT7 models US CA 590225B 04.
1 SAFETY AND WARNINGS WARNING! Electrical hazard Before installing the dishwasher, remove the house fuse or open the circuit breaker. If permanently connecting the dishwasher, be sure the power is isolated and the dishwasher unplugged. GROUNDING INSTRUCTIONS This appliance must be grounded. In the event of a malfunction or breakdown, grounding will reduce the risk of electric shock by providing a path of least resistance for electric current.
2 PARTS SUPPLIED Drain hose support (1) Moisture protection tape (1) (to prevent moisture damage) Drain hose joiner (1) Hexagonal socket for feet adjustment (2) (long & short) Wire clip (2) (for securing Drain hose joiner) Clamp (1) (for securing Drain hose joiner) Prefinished toekick (1) Side mounting bracket kit (A and B) (2) OPTIONAL Edge Protector (1) (If the services hole is through a metal partition the hole must be protected with the Edge protector supplied to prevent damage to the power
3 5 OPTIONALLY HARD WIRING PRIOR TO INSTALLATION 3a REMOVE THE LOWER DRAWER 3b REMOVE THE ACCESS COVER & POWER CORD 43 4 5 Access cover 1 6 8 To prevent kinked hoses, we recommend rotating the drawer anti-clockwise and resting 5 it on its side after removal. mm) 0m 41”0(100m 2 7 WARNING! Press the release tabs in on either side and push back to release drawer from runners. Electrical Shock Hazard Before continuing, ensure that the product is disconnected from the power supply.
4 PRODUCT DIMENSIONS 6 O K I Plan D C F A N Side G L O B E M H Product dimensions DD24DVT7 1 DD24DUT7 A B C D E F G H I J K L M N O J inches (mm) 34 - 36 3⁄8”(864-924)2 34 - 36 3⁄8”(864-924)2 overall width of product 23 13⁄16”(605) 23 13⁄16”(605) overall depth of product (excl. handle) 22 11⁄16”(577) 22 11⁄16”(577) depth of chassis (to back of front panel) 21 ¾”(553) 21 ¾”(553) maximum extension of drawer (excl.
5 CABINETRY DIMENSIONS 7 Q R S Plan Side P Minimum clearances from adjacent cabinetry T Cabinetry dimensions min. ½” (13 mm) clearance from a corner cupboard inches (mm) DD24DUT7 DD24DVT7 P Q R S T inside height of cavity* min. 34”(864) inside width of cavity 24”(610) inside depth of cavity min. 22 1⁄16”(560) recommended height of adjacent cabinet space height of toekick space* *depending on adjustment of leveling feet 30”(762) 3 15⁄16 - 6 5⁄16”(100-160) min.
6 CAVITY PREPARATION COUNTERTOP 3⁄8” (10mm) Moisture protection tape must be applied. 8 Important! The power outlet must be located in a cabinet adjacent to the dishwasher cavity. 110-120 VAC max. 15 A Water Connection Recommended HOT (Maximum 140°F/60°C). These marks indicate formed bracket screw locations, if securing by drawer removal. If there is no side partition, you can construct timber bracing as something to secure into. Supplied hose to suit 3⁄8” (9 mm) male compression fitting.
7 MAXIMUM DISTANCE OF HOSES & CORD FROM CHASSIS EDGE Left hand side Drain hoses - 78 ½” (2000 mm) Inlet hose - 64 ¾” (1650 mm) Power cord (excl. plug) - 29 ½” (750 mm) 9 Right hand side Drain hoses - 70 ½” (1800 mm) Inlet hose - 49 ” (1250 mm) Power cord (excl.
NOW CHOOSE WHICH INSTALLATION METHOD (a) or (b) IS MORE SUITABLE FOR YOUR CABINETRY... RECOMMENDED METHOD (a) - SECURE WITHOUT DRAWER REMOVAL (FRAMELESS CABINETRY ONLY) 9a PULL THROUGH HOSES & PUSH INTO THE CAVITY 8a ATTACH SIDE MOUNTING BRACKETS B Clip all four side mounting brackets into their slots using a flat-bladed screwdriver. Ensure they’re securely fitted before sliding product into cavity.
10a SECURE TO THE CABINETRY ON THE SIDES 11a OPTIONALLY SECURE TO THE CABINETRY ABOVE 1 (x2) Open the drawer halfway. Using a flat-bladed screwdriver, prize the gray rubber plug out of the trim moulding. 11 The top mounting brackets will only bend upwards a maximum of 3⁄8” (10 mm). Replace the gray rubber plug back into the trim moulding and ensure the trim seal is facing forward.
ALTERNATIVE METHOD (b) - SECURE BY DRAWER REMOVAL 8b PULL THROUGH HOSES & PUSH INTO THE CAVITY 9b REMOVE THE LOWER DRAWER To prevent kinked hoses, we recommend rotating the drawer counter-clockwise and resting it on its side after removal. (x2) optionally attach the two top mounting brackets 3 4 You can initially level the product 1 4 5 2 You can raise or lower the product by twisting the feet. Then take care when pushing the product into the cavity that you do not bend the feet.
10b SECURE TO THE CABINETRY ON THE SIDES To access the side brackets, you might have to push aside the insulation. After securing, ensure the sound insulation is repositioned correctly. For further adjustment, using the most appropriate length Hexagonal socket supplied, fully extend leveling feet up to required distance by hand. (x2) Secure using two pairs of formed brackets (use 5⁄8” (16 mm) screws). Repeat on the other side of the chassis.
13b FIT THE SUPPLIED TOEKICK PANEL 1 Where the toekick meets the bottom of the tub is the cut-off point 3 15 5 7 Mounting rail 19 9 Lay the toekick face down on a chopping board or similiar 4 Turn the toekick over and score along the same line 6 Smooth the edge with a file. Be careful of sharp edges. 8 2 Mark this point on the toekick with a pencil 19 Slide the toekick onto the mounting rails either side and screw the toekick onto the bottom of tub on either side.
14 THERE ARE THREE DIFFERENT DRAINAGE OPTIONS. CHOOSE WHICH IS MORE SUITABLE. If space is limited for fixing, push hose through drain hose support to required height Dishwasher using Air Break with Drain Hose Joiner If space is limited for fixing, push hose through drain hose support to required height 2 Supplied drain hose joiner Ø ¾” (19 mm) waste tee 750-882.5 29 ½”-34 ¾”mm (750-882.5 mm) 2 max. max.
FINAL CHECKLIST 18 TROUBLESHOOTING Check all parts are installed. Ensure product is level, securely fastened to the cabinetry and opens and closes freely. The drawers must be free to fully close with no resistance from the cabinetry. Ensure inlet hose to water supply has supplied rubber washer fitted, and that it’s tightened a further half turn after seal contact. Ensure any knockouts or plugs in drain connection have been drilled out and drain connection has been made.
