City 1.24/II Chimney and VMC - City 1.24/II FF City 2.24/II Chimney and VMC - City 2.24/II FF - City 2.28 FF City 3.24/II Chimney - City 3.24/II FF City 24 BIC/II - City 24 BIC/II FF City Condens 1.24, 2.24, 3.
Thanks Congratulations on choosing a DE DIETRICH product, a product of quality. We strongly recommend that you read the following instructions in order to guarantee the optimal operation of your appliance. We are sure that you will not be disappointed and that it will satisfy all of your expectations. Recommendations For a proper operating of the boiler, follow carefully the instructions.
Operating instructions - Check that the boiler is connected to the electricity. - Open the gas valve (See next page). M : Pressure indicator Displays the pressure in the heating circuit from 0.5 to 2.5 bar. If the red warming light (0.5 bar) is lit, top up with water using the filling system (disconnector, consult your fitter (See next page). G : Switch Turn the switch to the desired operating mode : 8 .
Control panel (City Condens 1.24, 2.24, 3.24) N Temperature display O 6-position switch T Domestic hot water temperature maintenance override button (1.24, 3.24) or Maintenance override button for the primary storage tank (2.
Operating instructions N : Temperature display Q : Unlock button The display shows the temperature of the water in the domestic hot water heating outlet when there is a request for domestic hot water. To restart the boiler after safety shutdown. V : Heating temperature setting O : 6-position switch - Setting range : 30 °C to 90 °C (Hard spot at 68°C) .
Gas connection you can smell gas : If- Close the gas valve - Open the windows - Do not operate switches - Extinguish all flames - Consult your fitter or the maintenance company - Inform the gas supplier. 1 Opening the gas valve on the boiler (Example with City 2.24/II) 1 Under the boiler, push the yellow lever upwards 2 Under the boiler, turn the lever a quarter turn 2 Checking the water pressure in the boiler (Example with City 2.24/II) The water pressure in the boiler must be between 1 and 2 bar.
3 Topping up the boiler with water (Example with City 2.24/II) A Under the boiler, open (+) the 2 valves until you reach a pressure of between 1 and 2 bar B Close the 2 valves (-) 4 Troubleshooting Checks to make before calling your fitter (30/90 : for City Condens) The burner is not working `It is cold. Example with City 2.24/II - Check the boiler thermostat settings.
`It is cold. There is no domestic hot water (Example with City 2.24/II) - Note the code displayed AL + _ _. Press button until the red light goes out. Release the button. The heater restarts. If there is a problem, contact your fitter, specifying the alarm code. Hot water takes a very long time to reach certain draw-off points and not others This is due to the length of the hot water pipes between the draw-off points and the boiler.
Warranty You have just purchased a DE DIETRICH appliance and we thank you for the trust you have placed in our products. France Please note that your appliance will provide good service for a longer period of time if it is regularly checked and maintained. The preceding dispositions are not exclusive of benefits for the purchaser of the legal guarantee as stated in Civil Code articles 1641 to 1648. Your fitter and the DE DIETRICH customer support network are at your disposal at all times.
CITY 31/08/05 - 300005627-001-A
CITY 31/08/05 - 300005627-001-A
DE DIETRICH THERMIQUE S.A.S. www.dedietrich.com In the interest of customers, De Dietrich Thermique SAS are continuously endeavouring to make improvements in product quality. All the specifications stated in this document are therefore subject to change without notice F Direction des Ventes France 57, rue de la Gare F- 67580 MERTZWILLER (+33) 03 88 80 27 00 (+33) 03 88 80 27 99 DE DIETRICH HEIZTECHNIK www.dedietrich.
