User Manual

ManualsBrandsDE DIETRICH ManualsDishwashersDVH640

CONTENTS

1 / SAFETY INSTRUCTIONS

• Important warnings __________________________________________ 14

2 / INSTALLING YOUR DISHWASHER

• Dimensions for building in appliances __________________________ 15

• List of parts supplied ________________________________________ 15

• Connecting to the water supply ________________________________ 16

• Draining away the waste water ________________________________ 17

• Electricla connection ________________________________________ 18

• Insertion into the niche ______________________________________ 19

• Levelling by adjusting the feet ________________________________ 19

• Fitting the door panel (Cladding with a single panel) ______________ 20

• Fitting the door panel (Cladding with two elements) ______________ 21

• Appliances built-in under o hob ________________________________ 22

• Fixing in the niche __________________________________________ 22

• Sound-proofing seals ________________________________________ 22

• Balancing the door (left and right) ______________________________ 22

• Refitting the plinth __________________________________________ 23

• Table for cutting away the plinth ______________________________ 23

Important:

When building in appliances, please use the attached installation diagram.

Important:

Please read this installations manual carefully in order to comply with the instruc-

tions for installing and fitting your machine.

NB:

This installations manual covers various models. There may be some slight diffe-

rences between your appliance and the descriptions shown.

Summary of content (11 pages)

PAGE 1
EN CONTENTS 1 / SAFETY INSTRUCTIONS • Important warnings __________________________________________ 14 2 / INSTALLING YOUR DISHWASHER • Dimensions for building in appliances __________________________ • List of parts supplied ________________________________________ • Connecting to the water supply ________________________________ • Draining away the waste water ________________________________ • Electricla connection ________________________________________ • Insertion into the niche ________________
PAGE 2
EN 1/ SAFETY INSTRUCTIONS • IMPORTANT WARNINGS Important: After unpacking your appliance, make sure that it has not suffered any damage during transport. Never connect up a damaged appliance. If your appliance is damaged, please contact your dealer. Danger: If your appliance operates incorrectly, disconnect it (pull out the plug) or switch off the circuit concerned and close the water supply tap. Contact our After-Sales Service.
PAGE 3
EN 2 / INSTALLING YOUR DISHWASHER • DIMENSIONS FOR BUILDING IN APPLIANCES You can insert your appliance under an existing worktop provided that the relevant niche corresponds to the dimensions on the sketch below (Fig. 01). ? 642 à 730 maxi 547 Fig.
PAGE 4
EN 2 / INSTALLING YOUR DISHWASHER • CONNECTING TO THE WATER SUPPLY This dishwasher can be supplied with cold water or hot water up to a maximum of 60°C. When supplying with hot water, check that your original hose allows such connection (red marking on the hose). However, we recommend that you connect to the cold water supply. Your appliance is fitted with a supply hose 1.50m long. Connect the hose to a tap with a threaded end, diameter 20/27 (3/4" BSP).
PAGE 5
EN 2 / INSTALLING YOUR DISHWASHER • DRAINING AWAY THE WASTE WATER You can connect the end of the drain hose to: - A ventilated U-bend (Fig. 2-1) or - A sink U-bend (Fig. 2-1) When connecting to a U-bend, you must remove the flapper from the U-bend. Then fully install the rubber end. If necessary, add a tightening collar P10 . NB: Ensure that the drain hose is held in place with a tie to avoid any potential flooding. The drain connection must be 0.30m (minimum) to 0.90m (maximum) above the floor (Fig.
PAGE 6
EN 2 / INSTALLING YOUR DISHWASHER • ELECTRICAL CONNECTION The appliance must be at a standstill when connecting to the electricity supply circuit. Before connecting your appliance, ensure that: - The mains voltage indicated on the manufacturer’s plate on your machine matches the voltage supplied by your installation. - Your meter and the fuses can support the current intensity for your dishwasher. A fuse of at least 10A is required.
PAGE 7
EN 2 / INSTALLING YOUR DISHWASHER • INSERTION INTO THE NICHE • Glue on the anti-condensation plate P2 (Fig. 3.1) • Glue on the foam sound-proofing seal P3 (Fig. 3.1) • Clip the three cups P1 under the feet to make the dishwasher easier to slide (Fig. 3.1). Fig. 3.1 If the worktop is in marble or a similar material, you must fix your dishwasher using the side screws; before inserting it into the niche, you must therefore unfold a flange on each side of the side panels (Fig. 3.2).
PAGE 8
EN 2 / INSTALLING YOUR DISHWASHER • FITTING THE DOOR PANEL (Cladding with a single panel) - Measure the distance between the floor and the bottom of the door panel on the adjacent unit (Dimension B, Fig. 5.1) (22) B A - Measure the distance between the floor and the marking on the bottom of the door panel (Dimension A) B D=A-B Fig. 5.1 - Calculate Dimension D = A - B, and draw a line for Dimension D on the back of the panel at the bottom (Fig. 5.
PAGE 9
EN 2 / INSTALLING YOUR DISHWASHER FITTING THE DOOR PANEL (Cladding with 2 elements) - To fit the first section, please refer to the previous chapter “FITTING THE DOOR PANEL (Cladding with a single panel) (Figs. 5.1 et 5.2). - Position your door panel by engaging the 2 screws in the holes in the dishwasher’s door (Fig. 6.2 A) Fig. 6.1 A - If there is any difficulty screwing, move the screw P6 22 mm. - Place the wood panel flat against the door (Fig. 6.2 A).
PAGE 10
EN 2 / INSTALLING YOUR DISHWASHER • APPLIANCES BUILT-IN UNDER A HOB Danger: If your worktop has a hob fitted above your dishwasher, you must fit thermal insulation on top of your dishwasher. You can obtain an insulation kit from your dealer. Remember to leave a space between the gas pipe and the top of your dishwasher. • FIXING IN THE NICHE Fasten the dishwasher under the worktop with the screws P9 (see Fig. 7) or using the flanges you have unfolded (Fig. 3.2).
PAGE 11
EN 2 / INSTALLING YOUR DISHWASHER • REFITTING THE PLINTH Refit the plinth, cutting it away if necessary according to Dimension P (see table and Fig. 10.1) Calculate dimension P (Table on last page): - Take Dimension B from Fig. 6.1 and measure the gap J between the floor and the bottom of the dishwasher. Calculate B - J. - Measure the plinth depth E (Fig. 10.1) between the unit’s plinth and front of the unit. Take the value for P from the table provided by E and B – J (e.g.