EUROCHEF - PRO WALL HOOD EUROCHEF - PRO WALL HOOD INSTALLATION INSTRUCTIONS 1 2 3 TIMER Shown with accessory Duct Cover Kit and accessory Warming Lamp Kit APPROVED FOR ALL RESIDENTIAL APPLIANCES FOR RESIDENTIAL USE ONLY PLEASE READ ENTIRE INSTRUCTIONS BEFORE PROCEEDING. INSTALLATION MUST COMPLY WITH ALL LOCAL CODES. IMPORTANT: Save these Instructions for the Local Electrical Inspector’s use. INSTALLER: Leave these Instructions with this unit for the owner.
EUROCHEF - PRO WALL HOOD HOODS WEIGHT MODEL NUMBER 24” range hood with 600 CFM blower 22 lbs EC PH24S 30” range hood with 600 CFM blower 30 lbs EC PH30S 36” range hood with 600 CFM blower 36 lbs EC PH36S 48” range hood with 1200 CFM blower 48 lbs EC PH48S FEATURES Controls: Fabrication: Features: ACCESSORIES 4-speed electronic with 15” minute delayed shutoff timer Welded, polished and brushed seams All edges hemmed 304 stainless hood baffle filter and grease tray 12V halogen lighting, lamps
EUROCHEF - PRO WALL HOOD READ THESE INSTRUCTIONS COMPLETELY AND CAREFULLY WARNING TO REDUCE THE RISK OF FIRE, ELECTRICAL SHOCK OR INJURY TO PERSONS, OBSERVE THE FOLLOWING: A. Use this unit only in the manner intended by the manufacturer. If you have any questions, contact the manufacturer. B. Before servicing or cleaning unit, switch power off at the service panel and lock service panel to prevent power from being switched on accidentally.
EUROCHEF - PRO WALL HOOD PRODUCT DIMENSIONS CONTENTS AND PAGE NUMBER Product Dimensions....................................................... pg.4 Advance Planning...........................................................pg.5 Using Duct Cover Accessories........................................ pg.5 Tools and Materials Required ......................................... pg.5 Remove the packaging................................................... pg.6 Parts Provided..........................................
EUROCHEF - PRO WALL HOOD ADVANCE PLANNING 36” (914 mm) Cabinetry and electrical placement for 24-inch deep wall hoods. lnstallatian dimensions for 24 deep wall hoods. USING DUCT COVER ACCESSORIES To avoid gaps, plan the hood installation height for duct cover use. Recirculating Kit Cover 4” (if used) Duct cover 6” Duct cover 12” 1. Duct covers and Recirculating Kit covers are stackable. 2. The hood is 18” tall and can be installed from 24” to 36” above cooking surface (30” to 36” is optimum). 3.
EUROCHEF - PRO WALL HOOD REMOVE THE RANGEHOOD Parts Included with your Hood DO NOT GRAB BODY HERE GRAB BODY HERE GRAB BODY HERE • Hood with blower installed • 12-Volt halogen bulbs, installed • Care & Use /Installation Instructions • Registration Card • Filters (24” & 30” = 2; 36” = 3; 48” = 4) • Grease trap (24” & 30” = 2; 36” = 3; 48” = 4) • Transition with Back draft damper • Fasteners • Wooden bracket for Hood Support Parts Not Included with your Hood LOCATION OF COMPONENTS PARTS
EUROCHEF - PRO WALL HOOD STEP 1 DETERMINE HOOD, DUCTWORK AND WIRING LOCATIONS • • Use a level to draw the cooktop centerline vertically up the wall to the ceiling. Measure desired distance from the bottom of the hood to the cooking surface, 24" min. to 36" max. Note: If installing with Duct Cover Kit or Recirculating Kit, see “Using Duct Cover Accessories”, pg 5 to eliminate gaps at ceiling. • Use a level to draw a straight horizontal pencil line indicating the bottom of the hood.
EUROCHEF - PRO WALL HOOD BLOWER POSITION CHART Hood size Motor Recirculating Kit option Top ducting option Rear ducting option 24” 30” 30” 36” 36” 48” 1 1 2* 1 2* 2 YES YES NO YES NO NO YES YES YES YES YES YES YES YES NO YES NO NO (*) with Blower Upgrade Kit BLOWER POSITION OPTION model 24 Vertical Discharge model 30 36 Vertical Discharge model 30 36 model 48 two blowers Vertical Discharge (with Blower Upgrade Kit) model 24 Horizontal Discharge model 30 36 Horizontal Discharge model 30 36 mo
EUROCHEF - PRO WALL HOOD IF CHANGING BLOWER POSITION SECURITY SCREW 1. Disconnect motor from power supply 2. Remove Blower security screw from blower bracket and remove blower. 3. Loosen 4 screws from blower bracket. 4. Shift blower to right and Remove Blower. 5. Loosen 4 screws and remove sealing plate covering back venting hole. 6. Reverse this procedure in new locations. 7. Reconnect blower to power supply.
EUROCHEF - PRO WALL HOOD STEP 3A: INSTALL HOOD ONTO WALL (see enclosed template) SKIP THIS STEP IF INSTALLING BENEATH A SOFFIT OR CABINET, GO TO STEP 3B. • • • • Affix enclosed paper template to wall. From the line indicating the bottom of the hood, measure 17” up and draw another line for the location of the Wood Bracket. See illustration. Locate at least 2 vertical studs at the Wood Bracket. Center the supplied Wood Bracket, left to right and below the marked line.
EUROCHEF - PRO WALL HOOD STEP 3B: ALTERNATE MOUNTING METHOD • Affix enclosed paper template to wall IMPORTANT: FRAMING MUST BE CAPABLE OF SUPPORTING UP TO 150 LBS INSTALL HOOD TO SOFFIT OR BENEATH CABINETS SKIP THIS STEP IF USING WALL MOUNTING METHOD When necessary, the hood may be installed so that it is supported by the soffit. • The soffit should be constructed with 2 x 4’s. • Determine the installation location on the wall. • Continue the centerline forward on the bottom of the cabinet or soffit.
EUROCHEF - PRO WALL HOOD STEP 4: • • CONNECT DUCTWORK Install ductwork. Secure joints in ductwork and transition with sheetmetal screws and duct tape for an airtight seal. ATTENTION: Be sure that screws do not hamper the dampers movement. • STEP 5: • • Use wire nuts to connect incoming ground, neutral and hot. Push wires into junction box and replace cover. Be sure wires are not pinched. STEP 6: INSTALL DUCT COVERS CONNECT ELECTRICAL Verify that power is turned off at the source.
EUROCHEF - PRO WALL HOOD STEP 7: • • • • TIGHTEN - HANGING SCREWS With Filter Frame still removed from Step 2 Adjust hood up to eliminate any gaps at ceiling. Tighten hanging screws. Add (2) more security screws + Washers at wood bracket. IMPORTANT: If Installing optional Backsplash Kit install this kit BEFORE installing wall anchors (see instruction with kit) Install Bottom Wall Anchors • • • • Drill 1//8" pilot holes into the two lower mounting holes.
EUROCHEF - PRO WALL HOOD STEP 9: INSTALL FILTER STEP 10: TEST FUNCTION OF HOOD - Blower - Light • Place filter drip trays into the bottom rear of the hood. • Insert top of grease filter first, than rotate bottom filter and drop into grease tray. • To remove the filters, grasp the handle, push the filter up and lift out.
EUROCHEF - PRO WALL HOOD CARE AND USE OPERATION REPLACING HALOGEN BULB Press any speed to turn hood on. Press same button to turn hood off. Active speed is shown by a button back light. ROTATE CONTROL: 1. 2. 3. 4. 1 Speed 2 Speed 3 Speed 4 Speed Light DELAYED SHUTOFF By pressing down on any speed key for 2 seconds, while hood is running the 15 minute Delayed Shutoff mode will start indicated by flashing backlight. After 15 minutes the hood will shutoff.
EUROCHEF - PRO WALL HOOD EUROCHEF U.S.A. 41 MERCEDES WAY SUITE 25 EDGEWOOD NEW YORK 11717 – TEL. 866-844-6566 WWW.DELONGHIMAJORAPPLIANCES.COM WWW.DELONGHI RANGES.