(High Efficiency Common Cabinet Decathlon Fryers) High Efficiency Decathlon (HD) Series Gas Fryers Service & Parts Manual HDC, CFHDC, SCFHDC, FPHDC, Y/KSCF/C/HC, BK1814 Dean, a member of the Commercial Food Equipment Service Association, recommends using CFESA Certified Technicians.
Please read all sections of this manual and retain for future reference. This product has been certified as commercial cooking equipment and MUST be installed by professional personnel as specified. Installation, maintenance and repairs should be performed by your FRYMASTER AUTHORIZED SERVICE AGENCY. DANGER Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other cooking appliance.
WARNING Drawings and photos used in this manual are intended to illustrate operational, cleaning and technical procedures and may not conform to on-site management operational procedures. WARNING No structural material on the fryer should be altered or removed to accommodate placement of the fryer under a hood. Questions? Call the Frymaster and Dean Service Hotline at 1-800-5518633.
High Efficiency Decathlon (HD) Series Gas Fryers Service and Parts Manual TABLE OF CONTENTS 1. SERVICE PROCEDURES……..……..……………………………………………... 1.1 Functional Description............................................................................................1-1 1.2 Accessing Fryers for Service...................................................................................1-7 1.3 Cleaning the Gas Valve Vent Tube (if applicable)................................................1-9 1.
Burners Drain Valve Handle (Red) Oil Return Handle (Yellow) Drain Flush Handle (Blue) Flue Cap Filter Unit Frypot Gas Valve Oil Return Handle Electronic Operating Thermostat Top Cap Note: The appearance of your fryer may differ slightly from that shown depending upon configuration and date of manufacture.
HIGH EFFICIENCY DECATHLON SERIES GAS FRYERS CHAPTER 1: SERVICE PROCEDURES 1.1 Functional Description High Efficiency Decathlon (HD) Series gas fryers contain a welded stainless steel frypot heated by gas flames diffused evenly through tubes built into the frypot. Flames originate from orifices in a burner manifold positioned beneath cast-steel burners. The burners are positioned in the tube openings at the front of the frypot.
HIGH EFFICIENCY DECATHLON SERIES GAS FRYERS CHAPTER 1: SERVICE PROCEDURES 1.1 Functional Description (cont.) Pilot System Configuration The pilot system is comprised of the pilot orifice, pilot hood, and a thermopile (some systems incorporate a thermocouple). The pilot serves two purposes: light the burner and heat the thermopile. In operation, the thermopile is in contact with the pilot flame and generates millivolts.
HIGH EFFICIENCY DECATHLON SERIES GAS FRYERS CHAPTER 1: SERVICE PROCEDURES Electronic Ignition Configuration (cont.) At start-up the ON/OFF switch is placed in the ON position, supplying 12 VDC to the heat control circuitry in the controller or controller and to one side of the heat relay coil on the interface board.
HIGH EFFICIENCY DECATHLON SERIES GAS FRYERS CHAPTER 1: SERVICE PROCEDURES Interface Boards (cont.) 106-3729 (24V): These boards are used in HD fryers equipped with Thermatron control systems. THERMATRON BOARD P/N 106-3729 Thermatron systems incorporate a temperature probe, a potentiometer, and a temperature control circuit board. This system is more accurate and reliable than a standard thermostat.
HIGH EFFICIENCY DECATHLON SERIES GAS FRYERS CHAPTER 1: SERVICE PROCEDURES Interface Boards (cont.) 826-2434: These interface boards are used in HD fryers equipped with electronic ignition and constant pilot. INTERFACE BOARD P/N 826-2434 Used on fryers equipped with electronic ignition and constant pilot.
HIGH EFFICIENCY DECATHLON SERIES GAS FRYERS CHAPTER 1: SERVICE PROCEDURES Interface Boards (cont.
HIGH EFFICIENCY DECATHLON SERIES GAS FRYERS CHAPTER 1: SERVICE PROCEDURES Thermostats Different types of thermostats are used in High Efficiency Decathlon Series gas fryers, depending on fryer configuration. Fryers equipped with a Thermatron use a dial to adjust temperature. In this configuration, the probe resistance varies inversely with the temperature. As the temperature rises, resistance decreases at a non-linear rate. A chart is located at the end of this chapter.
HIGH EFFICIENCY DECATHLON SERIES GAS FRYERS CHAPTER 1: SERVICE PROCEDURES Restraints Once the fryer has been positioned at the frying station, use a carpenter’s level placed across the top of the frypot to verify that the unit is level, both side-to-side and front-to-back. To level fryers equipped with legs, the bottom of the legs can be screwed out up to one inch for leveling. Legs should also be adjusted so that the fryer(s) are at the proper height in the frying station.
HIGH EFFICIENCY DECATHLON SERIES GAS FRYERS CHAPTER 1: SERVICE PROCEDURES 1.3 Cleaning the Gas Valve Vent Tube (if applicable) 1. Set the fryer power switch and the gas valve to the OFF position. 2. Carefully unscrew the vent tube from the gas valve. NOTE: The vent tube may be straightened for ease in removal. 3. Pass a piece of wire through the tube to remove any obstruction. Remove the wire and blow through the tube to ensure it is clear. 4.
HIGH EFFICIENCY DECATHLON SERIES GAS FRYERS CHAPTER 1: SERVICE PROCEDURES 1.5 Adjusting the Pilot Flame 1.5.1 Main Pilot 1. Remove the cap from the pilot adjustment screw hole on the gas valve. 2. Using a small, flat-tipped screwdriver, turn the pilot adjusting screw counterclockwise to increase length of flame or clockwise to decrease length of flame. Adjust to obtain a flame from 1 inch to 1½ inches long. 3. Reinstall the pilot adjustment screw cap. 1.5.
HIGH EFFICIENCY DECATHLON SERIES GAS FRYERS CHAPTER 1: SERVICE PROCEDURES 1.7 Replacing Fryer Components 1.7.1 Replacing the Controller 1. Disconnect the fryer from the electrical supply. 2. Unscrew the two controller panel screws. The controller panel is hinged at the bottom and will swing open from the top. Computer panel in “down” position. 3. Unplug the fryer wiring harness and ground wire from the back of the controller. 4.
HIGH EFFICIENCY DECATHLON SERIES GAS FRYERS CHAPTER 1: SERVICE PROCEDURES 1.7.2 Replacing the Temperature Probe; Controller-equipped Fryers 1. Disconnect the fryer from the electrical supply. 2. Drain cooking oil from the frypot. Allow the frypot to cool completely before proceeding. 3. Remove fryer door for easier access to the temperature probe. First, remove top hinge from bracket. Then, lift door off bottom hinge pin. Remove the fryer door for easier access to the temperature probe. 4.
HIGH EFFICIENCY DECATHLON SERIES GAS FRYERS CHAPTER 1: SERVICE PROCEDURES 1.7.2 Replacing the Temperature Probe; Controller-equipped Fryers (cont.) 6. Remove the burner shield by loosening the screw on each end. 7. Remove the burner rail by loosening the screw on each end. The burner rail secures the burners in the burner manifold. Be careful to ensure that the burners do not fall out of the gas manifold, as they might be damaged and dented. Remove the burner rail and burner shield. 8.
HIGH EFFICIENCY DECATHLON SERIES GAS FRYERS CHAPTER 1: SERVICE PROCEDURES 1.7.2 Replacing the Temperature Probe; Controller-equipped Fryers (cont.) 10. Locate the temperature probe inside the frypot. 11. The temperature probe can be removed through the bottom of the frypot as follows: Ensure the two-pin connector has been removed from the probe wiring harness (step 4, above). Carefully bend the two tabs (one forward and toward the back) so the probe will clear the tabs. Remove the harness insulation.
HIGH EFFICIENCY DECATHLON SERIES GAS FRYERS CHAPTER 1: SERVICE PROCEDURES Installing the New Temperature Probe: 1. Feed the probe wire through the probe nipple from the top side of the frypot. 2. Loosely install the bladder nut. 3. Mount the probe into the mounting hardware. Carefully bend the two tabs back into alignment to retain probe. 4. Tighten the bladder nut. 5. Install the insulation and plug. 1.7.3 Replacing the High-limit Thermostat 1. Turn fryer off and drain oil from the frypot. proceeding.
HIGH EFFICIENCY DECATHLON SERIES GAS FRYERS CHAPTER 1: SERVICE PROCEDURES 1.7.3 Replacing the High-limit Thermostat (cont.) 6. Locate the high-limit probe inside the frypot. Carefully bend the outer tab at the rear of the high limit until the high limit can slid back and out of the retaining bracket. Locate the high-limit probe. 7. Carefully pull high-limit capillary tube and bulb out of the frypot from the bottom. Remove high-limit capillary tube and bulb from the bottom of the frypot.
HIGH EFFICIENCY DECATHLON SERIES GAS FRYERS CHAPTER 1: SERVICE PROCEDURES 1.7.3 Replacing the High-limit Thermostat (cont.) 8. Mark and disconnect wires at the high-limit in the component box. Mark and disconnect high-limit wiring (arrows). Reconnect wires to the same terminals on the replacement high-limit. 9. Remove high-limit from fryer by pulling the capillary tube and bulb through the component box opening (arrow). This may require removal of the control panel frame. 10.
HIGH EFFICIENCY DECATHLON SERIES GAS FRYERS CHAPTER 1: SERVICE PROCEDURES 1.7.4 Replacing Rocker Switches 1. Disconnect the fryer from the electrical supply. 2. If switches are located in a control box within the fryer, remove the six screws securing the switch panel to the control box. Do not allow the switch panel to hang from the switch wiring harness or other wires.
HIGH EFFICIENCY DECATHLON SERIES GAS FRYERS CHAPTER 1: SERVICE PROCEDURES 1.7.4 Replacing Rocker Switches (cont.) 3. Depress the retaining clips (see illustration below) and push the switch out of the slot. If there is a switch-guard present, retain it for installation of the replacement switch. Depress clips on each side to remove switch from control panel. 4. Remove wires one at a time from the switch being removed and connect to the replacement switch until all wires are transferred. 5.
HIGH EFFICIENCY DECATHLON SERIES GAS FRYERS CHAPTER 1: SERVICE PROCEDURES 1.7.6 Replacing the Pilot Assembly 1. Remove the pilot tubing from the bottom of the pilot assembly. 2. If the pilot is an electronic ignition pilot, disconnect the ignition cable and the sense wire. 3. Remove the pilot mounting screw(s) from the pilot mounting bracket and remove the pilot. 4. Reverse the procedure to replace the pilot assembly.
HIGH EFFICIENCY DECATHLON SERIES GAS FRYERS CHAPTER 1: SERVICE PROCEDURES 1.7.7 Replacing the Frypot (cont.) 6. Remove the top cap. It is held in place by one screw on each side of the fryer. If the fryer has a controller on the front, the top cap may also be held in place by two screws on the front of each pot. FPHD65 units may have two screws on each end of the top cap. 7. Remove the joiner strips on either side of the frypot. Be careful not to bend the joiner strip during removal.
HIGH EFFICIENCY DECATHLON SERIES GAS FRYERS CHAPTER 1: SERVICE PROCEDURES 1.7.7 Replacing the Frypot (cont.) 10. Remove screws securing flue cap to frypot (access from above; a nut-driver with an extension or long screwdriver is required). Use care not to drop the screws into the flues. If this happens, the screws can be retrieved when the flue is removed (Step 12). Use a screwdriver or similar tool to free flue cap from frypots. Remove flue cap by lifting up and off of fryer.
HIGH EFFICIENCY DECATHLON SERIES GAS FRYERS CHAPTER 1: SERVICE PROCEDURES 1.7.7 Replacing the Frypot (cont.) 12. Remove screws securing flue to frypot (access from above; a nut-driver with an extension or long screwdriver is required). Retrieve any screws dropped into the flue during removal of the flue cap and frypot bracket. Removing bolts (arrows) securing flue to frypot. 13. Remove the clevis clip and oil return handle rod from the oil return valve at the rear of the fryer.
HIGH EFFICIENCY DECATHLON SERIES GAS FRYERS CHAPTER 1: SERVICE PROCEDURES 1.7.7 Replacing the Frypot (cont.) 15. Remove the drain manifold. Only the drain tubes directly blocking the frypot being replaced require removal. - Remove the nuts holding the drain valve strap onto the drain tube stud. - Disconnect the Teflon tube at the back of the center dump tube piece and any other components attached to the tubes, including drain flush flexlines.
HIGH EFFICIENCY DECATHLON SERIES GAS FRYERS CHAPTER 1: SERVICE PROCEDURES 1.7.7 Replacing the Frypot (cont.) 20. If the fryer is equipped with drain-valve microswitches, mark the wires and microswitch terminals, then disconnect wires from the switch. Secure the wires to prevent damage when frypot is removed. Left: Microswitch wires marked for removal (ensure microswitch terminals are marked the same as the wires removed). Right: Microswitch mounted to drain valve. 21.
HIGH EFFICIENCY DECATHLON SERIES GAS FRYERS CHAPTER 1: SERVICE PROCEDURES 1.7.7 Replacing the Frypot (cont.) 23. Remove the temperature probe from frypot. (See Section 1.7.2, Replacing the Temperature Probe: Controller–equipped Fryers, for specific instructions.) 24. Remove the high-limit from the frypot (see Section 1.7.3, Replacing the High-limit Thermostat). 25. Remove bolts from brackets securing burner manifold to frypot. Leave the manifold in place.
HIGH EFFICIENCY DECATHLON SERIES GAS FRYERS CHAPTER 1: SERVICE PROCEDURES 1.7.7 Replacing the Frypot (cont.) 27. Ensure wires and tubes will not be caught on the frypot when it is removed. 28. Remove frypot from fryer by lifting up and out. 29. Position the frypot upside down on a suitable work surface. Lifting frypot from fryer. 30. Record position of the valve stem in relation to the frypot prior to removing the drain valve.
HIGH EFFICIENCY DECATHLON SERIES GAS FRYERS CHAPTER 1: SERVICE PROCEDURES 1.8 Troubleshooting and Problem Isolation Because it is not feasible to include every issue that might occur, this section is intended to provide technicians with a general knowledge of the broad problem categories associated with this equipment and the probable causes of each. With this knowledge, the technician should be able to isolate and correct any problem encountered.
HIGH EFFICIENCY DECATHLON SERIES GAS FRYERS CHAPTER 1: SERVICE PROCEDURES 1.8.1 Ignition Failure (cont.) The Electronic Circuits If gas and electrical power are supplied to the fryer, the next most likely cause of ignition failure is a problem in the 24 VAC circuit of fryers equipped with electronic ignition systems, or in the pilot system for those without electronic ignition. If the fryer is equipped with a SUFF/UFF filtration system, verify that the drain valve is fully closed.
HIGH EFFICIENCY DECATHLON SERIES GAS FRYERS CHAPTER 1: SERVICE PROCEDURES 1.8.2 Improper Burner Function (cont.) If popping occurs only during peak operating hours, the problem may be incorrect or fluctuating gas pressure. Verify that the incoming gas pressure (pressure to the gas valve) is in accordance with the appropriate requirements listed in the Installation and Operation manual that came with the fryer, and that the pressure remains constant throughout all hours of usage.
HIGH EFFICIENCY DECATHLON SERIES GAS FRYERS CHAPTER 1: SERVICE PROCEDURES 1.8.2 Improper Burner Function (cont.) Burners lighting on the left side only may be caused by a trailing pilot problem (four- and five-tube frypots) or improper burner manifold pressure. Fluctuating flame intensity is normally caused by either improper or fluctuating incoming gas pressure, but may also be the result of variations in the kitchen atmosphere.
HIGH EFFICIENCY DECATHLON SERIES GAS FRYERS CHAPTER 1: SERVICE PROCEDURES 1.8.4 Improper Controller Function Sensitivity or "Stretch Time." Sensitivity—or stretch time—is a programmable feature that increases the cook time countdown based on variations in the oil temperature from the setpoint (e.g., when cold product is dropped into the oil, causing the oil temperature to drop). The sensitivity for each product button has 10 settings (0 through 9).
HIGH EFFICIENCY DECATHLON SERIES GAS FRYERS CHAPTER 1: SERVICE PROCEDURES 1.8.5 Improper Filtration Function The majority of filtration problems arise from operator error. One of the most common errors is placing the filter paper on the bottom of the filter pan rather than over the filter screen. Anytime the pump is running, but no oil is being filtered, check the installation and size of the filter paper. Verify that the O-rings on the slip-connection are in good condition.
HIGH EFFICIENCY DECATHLON SERIES GAS FRYERS CHAPTER 1: SERVICE PROCEDURES 1.8.5 Improper Filtration Function (cont.) Incorrectly sized or installed paper will allow food particles and sediment to pass through and clog the suction tube on the bottom of the filter carriage. Particles large enough to block the suction tube may indicate that the crumb tray is not being used. Pan blockage can also occur if shortening is left in the pan and allowed to solidify.
HIGH EFFICIENCY DECATHLON SERIES GAS FRYERS CHAPTER 1: SERVICE PROCEDURES 1.8.7 Improper Basket Lift Function Bell-Crank Basket Lifts Most High Efficiency Decathlon Series gas fryers are equipped with a bell-crank style basket lift. A cam and a bell crank are connected to the basket lift arm by a flat metal link. The cam is attached to a drive motor. The motor rotates the cam, raising or lowering the lift arm linked to the bell crank. A roller-activated microswitch is used to limit travel.
HIGH EFFICIENCY DECATHLON SERIES GAS FRYERS CHAPTER 1: SERVICE PROCEDURES 1.9 Troubleshooting Guides The following troubleshooting guides are intended to assist service technicians in quickly isolating the probable causes of equipment malfunctions by following a logical, step-by-step process. PROBABLE CAUSES PROBLEM Burner will not ignite. A. ON/OFF switch is off. Light in ON/OFF switch is not illuminated. CORRECTIVE ACTION A. Turn ON/OFF switch on. ON/OFF switch is on, A. No voltage at switch.
HIGH EFFICIENCY DECATHLON SERIES GAS FRYERS CHAPTER 1: SERVICE PROCEDURES 1.10 Wiring Diagrams Note: The diagrams in this section depict wiring as of the date of manual publication. It may not reflect design changes made to the equipment after publication. Refer to the wiring diagram affixed to the unit when actually troubleshooting this equipment. 805-1545 B 1.10.
HIGH EFFICIENCY DECATHLON SERIES GAS FRYERS CHAPTER 1: SERVICE PROCEDURES 805-1599 B 1.10.
HIGH EFFICIENCY DECATHLON SERIES GAS FRYERS CHAPTER 1: SERVICE PROCEDURES 1.10.3 BK1814 Main Wiring Diagram prior after Sep.
HIGH EFFICIENCY DECATHLON SERIES GAS FRYERS CHAPTER 1: SERVICE PROCEDURES 1.10.4 BK1814 Main Wiring Diagram prior to Sep.
HIGH EFFICIENCY DECATHLON SERIES GAS FRYERS CHAPTER 1: SERVICE PROCEDURES 1.10.
HIGH EFFICIENCY DECATHLON SERIES GAS FRYERS CHAPTER 1: SERVICE PROCEDURES 1.10.
HIGH EFFICIENCY DECATHLON SERIES GAS FRYERS CHAPTER 1: SERVICE PROCEDURES 1.10.
HIGH EFFICIENCY DECATHLON SERIES GAS FRYERS CHAPTER 1: SERVICE PROCEDURES 1.10.
HIGH EFFICIENCY DECATHLON SERIES GAS FRYERS CHAPTER 1: SERVICE PROCEDURES 1.10.
HIGH EFFICIENCY DECATHLON SERIES GAS FRYERS CHAPTER 1: SERVICE PROCEDURES 1.10.
HIGH EFFICIENCY DECATHLON SERIES GAS FRYERS CHAPTER 1: SERVICE PROCEDURES 1.10.
HIGH EFFICIENCY DECATHLON SERIES GAS FRYERS CHAPTER 1: SERVICE PROCEDURES 1.10.
HIGH EFFICIENCY DECATHLON SERIES GAS FRYERS CHAPTER 1: SERVICE PROCEDURES 1.10.
HIGH EFFICIENCY DECATHLON SERIES GAS FRYERS CHAPTER 1: SERVICE PROCEDURES 1.10.
HIGH EFFICIENCY DECATHLON SERIES GAS FRYERS CHAPTER 1: SERVICE PROCEDURES 1.
HIGH EFFICIENCY DECATHLON SERIES GAS FRYERS CHAPTER 2: PARTS LIST 2.1 High Efficiency Common Cabinet Decathlon (HDC) Primary Components 2.1.
HIGH EFFICIENCY DECATHLON SERIES GAS FRYERS CHAPTER 2: PARTS LIST Each section is labeled by size (e.g., D50) and parts are not interchangeable between different sized fryers. The parts in this manual are for use on Common Cabinet style fryer. If you have any questions, call the Frymaster and Dean 24-Hour Service Hotline, 1-800-551-8633. 2.1.
HIGH EFFICIENCY DECATHLON SERIES GAS FRYERS CHAPTER 2: PARTS LIST 2.1.
HIGH EFFICIENCY DECATHLON SERIES GAS FRYERS CHAPTER 2: PARTS LIST 2.1.2 Decathlon HD60/63 Primary Components (cont.
HIGH EFFICIENCY DECATHLON SERIES GAS FRYERS CHAPTER 2: PARTS LIST 2.1.2 Decathlon HD60/63 Primary Components (cont.
HIGH EFFICIENCY DECATHLON SERIES GAS FRYERS CHAPTER 2: PARTS LIST 2.1.
HIGH EFFICIENCY DECATHLON SERIES GAS FRYERS CHAPTER 2: PARTS LIST 2.1.3 Decathlon HD/FPHD65 Primary Components (cont.
HIGH EFFICIENCY DECATHLON SERIES GAS FRYERS CHAPTER 2: PARTS LIST 2.1.3 Decathlon HD/FPHD65 Primary Components (cont.
HIGH EFFICIENCY DECATHLON SERIES GAS FRYERS CHAPTER 2: PARTS LIST 2.1.
HIGH EFFICIENCY DECATHLON SERIES GAS FRYERS CHAPTER 2: PARTS LIST 2.1.4 Y/KSCF/C/HC Primary Components (cont.
HIGH EFFICIENCY DECATHLON SERIES GAS FRYERS CHAPTER 2: PARTS LIST 2.1.
HIGH EFFICIENCY DECATHLON SERIES GAS FRYERS CHAPTER 2: PARTS LIST 2.1.5 BK1814 Primary Components (cont.
HIGH EFFICIENCY DECATHLON SERIES GAS FRYERS CHAPTER 2: PARTS LIST 2.2 Orifices ITEM PART # * * * * * * * * * 810-2060 810-3801 810-3132 810-2938 810-3053 810-3054 810-3055 810-3056 810-3057 * * * * * * * * * 810-2939 810-2940 810-3058 810-3059 810-3060 810-3061 810-3062 810-0710 810-2059 COMPONENT Natural Orifices 2.40 mm CE 2.35 mm (China) 2.20 mm 0-1999 ft. 2.26mm 2000-3999 ft. 2.18mm 4000-5999 ft. 2.10mm 6000-7999 ft. 2.04mm 8000-8999 ft. 1.98mm 9000-10000 ft. 1.94mm Propane Orifices 0-1999 ft. 1.
HIGH EFFICIENCY DECATHLON SERIES GAS FRYERS CHAPTER 2: PARTS LIST 2.
HIGH EFFICIENCY DECATHLON SERIES GAS FRYERS CHAPTER 2: PARTS LIST 2.3 Additional Components and Controllers (cont.
HIGH EFFICIENCY DECATHLON SERIES GAS FRYERS CHAPTER 2: PARTS LIST 2.4 Drain System Components 2.4.
HIGH EFFICIENCY DECATHLON SERIES GAS FRYERS CHAPTER 2: PARTS LIST 2.4.1 3" Drain Manifold Components ITEM 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 PART # 823-5188 823-7664 823-4681 823-4682 812-1764 823-6315 823-5911 812-1998 812-1901 812-2006 812-1908 823-6100 823-5968 200-6751 200-9365 200-6752 220-6660 812-1999 823-7662 823-7452 17 18 19 20 812-2008 823-5910 823-7633 823-7663 21 22 23 24 25 26 27 823-7520 823-7667 823-7462 823-7668 823-7461 809-0969 816-0729 (cont.
HIGH EFFICIENCY DECATHLON SERIES GAS FRYERS CHAPTER 2: PARTS LIST 2.4.
HIGH EFFICIENCY DECATHLON SERIES GAS FRYERS CHAPTER 2: PARTS LIST 2.4.2 Drain Valve Assemblies (cont.
HIGH EFFICIENCY DECATHLON SERIES GAS FRYERS CHAPTER 2: PARTS LIST 2.
HIGH EFFICIENCY DECATHLON SERIES GAS FRYERS CHAPTER 2: PARTS LIST 2.5 Oil Return System (cont.
HIGH EFFICIENCY DECATHLON SERIES GAS FRYERS CHAPTER 2: PARTS LIST 2.
HIGH EFFICIENCY DECATHLON SERIES GAS FRYERS CHAPTER 2: PARTS LIST 2.6 Additional Oil Return Components (cont.
HIGH EFFICIENCY DECATHLON SERIES GAS FRYERS CHAPTER 2: PARTS LIST 2.7 Oil Disposal Plumbing (Popeye's) ITEM 1 2 3 4 5 6 7 8 PART # 108-1121 810-0278 900-5953 814-0047 108-1117 810-2379 813-0699 823-7153 816-0631 810-0487 DESCRIPTION Valve, Oil Disposal Valve Handle Sleeve Oil Disposal Assembly Hose, 107.
HIGH EFFICIENCY DECATHLON SERIES GAS FRYERS CHAPTER 2: PARTS LIST 2.
HIGH EFFICIENCY DECATHLON SERIES GAS FRYERS CHAPTER 2: PARTS LIST 2.9 Over-the-Top Oil Return System ITEM 1 2 3 4 5 6 7 PART # 810-1669 810-1680 810-2513 810-2699 810-2700 810-3234 813-0093 DESCRIPTION Adapter, Female ⅞" O.D. x ½" Flexline, ⅝" I.D. x 6.
HIGH EFFICIENCY DECATHLON SERIES GAS FRYERS CHAPTER 2: PARTS LIST 2.10 Filtration Components 2.10.
HIGH EFFICIENCY DECATHLON SERIES GAS FRYERS CHAPTER 2: PARTS LIST 2.10.2 Filtration Components; SCFHDC60 Series Fryers ITEM 1 * 2 3 4 5 6 * PART # 823-6018 823-7110 810-3540 200-5726 823-6338 810-2805 809-0070 823-6403 DESCRIPTION Basket, Crumb Basket, Crumb (Raising Cane's) Ring, Hold-down Screen, Sana Grid Pan, Filter Caster, 2" Filter Pan Nut, ¼-20 Hex, S/S Lid (mounted in frame) * Not illustrated.
HIGH EFFICIENCY DECATHLON SERIES GAS FRYERS CHAPTER 2: PARTS LIST 2.10.3 Filtration Components; Y/K/SCF/C/HC218 and 63 Series Fryers 1 2 3 5 4 6 7 ITEM 1 2 3 4 5 6 7 * PART # 823-6172 810-3195 106-7330SP 823-7534 813-0568 810-2805 809-0823 823-6507 DESCRIPTION Basket, Crumb Ring, Hold-down Screen Assembly, Filter Pan, Filter Plug, ⅛" NPT, Socket-Head Caster, 2" Filter Pan Nut, Nylock, ¼-20 Lid (mounted in frame) * Not illustrated.
HIGH EFFICIENCY DECATHLON SERIES GAS FRYERS CHAPTER 2: PARTS LIST 2.10.
HIGH EFFICIENCY DECATHLON SERIES GAS FRYERS CHAPTER 2: PARTS LIST 2.10.5 Filtration Components; Y/KSCF/C/HC218 Export (India) Series Fryers after May 2010 ITEM 1 2 3 4 5 6 7 * PART # 823-7904 810-3195 823-7834 106-7330SP 823-7534 813-0568 810-2805 809-0823 DESCRIPTION Basket, Crumb Ring, Hold-down Lid Screen Assembly, Filter Pan, Filter Plug, ⅛" SS NPT, Sq-Head Caster, 2" Filter Pan Nut, Nylock, ¼-20 * Not illustrated.
HIGH EFFICIENCY DECATHLON SERIES GAS FRYERS CHAPTER 2: PARTS LIST 2.10.6 Filtration Components; 65 Series Fryers (Filter Paper Option) ITEM 1 2 3 4 5 6 7 * PART # 823-6018 810-3540 200-5726 813-0568 823-6304 810-2805 809-0823 823-5857 DESCRIPTION Basket, Crumb Ring, Hold-down Screen, Sana Grid Plug, ⅛" NPT, Socket-Head Pipe Pan, Filter Caster, 2" Filter Pan Nut, Nylock, ¼-20 Lid (mounted in frame) * Not Illustrated.
HIGH EFFICIENCY DECATHLON SERIES GAS FRYERS CHAPTER 2: PARTS LIST 2.10.7 Filtration Components; 65 Series Fryers (Filter Leaf Option) ITEM 1 2 3 4 5 6 * PART # 823-5851 106-6466SP 106-8399 823-5258SP 810-2805 809-0070 823-5857 DESCRIPTION Basket, Crumb Filter Leaf with Suction Tube Assembly Filter Leaf (screen only) Filter Pan Caster, 2" Nut, ¼"-20 Hex Lid (mounted in frame) * Not Illustrated.
HIGH EFFICIENCY DECATHLON SERIES GAS FRYERS CHAPTER 2: PARTS LIST 2.
HIGH EFFICIENCY DECATHLON SERIES GAS FRYERS CHAPTER 2: PARTS LIST 2.11 Basket Lift Components (cont.
HIGH EFFICIENCY DECATHLON SERIES GAS FRYERS CHAPTER 2: PARTS LIST 2.
HIGH EFFICIENCY DECATHLON SERIES GAS FRYERS CHAPTER 2: PARTS LIST 2.12 Accessories (cont.
HIGH EFFICIENCY DECATHLON SERIES GAS FRYERS CHAPTER 2: PARTS LIST 2.14 Flexlines 17.50 (± 1.00) Typical Flexline LENGTH PART NUMBER LENGTH PART NUMBER 3.0-inch 810-1160 13.0-inch 810-1057 4.5-inch 810-1339 17.5-inch 810-1369 5.0-inch 810-1159 21.0-inch 810-1400 6.5-inch 810-1680 21.5-inch 810-1068 8.5-inch 810-1067 29.5-inch 810-1069 9.5-inch 810-1043 53.5-inch 810-1056 11.5-inch 810-1055 Flexlines come with a ⅞-inch female fitting on each end.
HIGH EFFICIENCY DECATHLON SERIES GAS FRYERS CHAPTER 2: PARTS LIST Appendix: Pre-Common Cabinet HD65 Parts List ITEM * * * * * PART # 823-5243 810-2072 810-2032 810-2155 812-1674 * 812-1677 * * * * * * * * * * * * * * * * * * * 810-0705 810-0703 220-1231 230-1431 810-2785 200-8748 200-8053 230-2057 807-3552 807-3628 807-3294 807-3295 810-2156 810-2323 807-2091 807-2127 810-0691 823-3347 * * * * * * * * * * * 106-7441 106-7357 106-6851 823-4894 823-4895 823-5136 823-5137 211-8078 212-8078 221-0012 222
HIGH EFFICIENCY DECATHLON SERIES GAS FRYERS CHAPTER 2: PARTS LIST Appendix: Pre-Common Cabinet HD65 Parts List (cont.
THIS PAGE INTENTIONALLY LEFT BLANK
Dean, 8700 Line Avenue, 8700 Line Avenue, Shreveport, Louisiana 71106 TEL 1-318-865-1711 PRINTED IN THE UNITED STATES FAX (Parts) 1-318-688-2200 SERVICE HOTLINE 1-800-551-8633 FAX (Tech Support) 1-318-219-7135 819-6314 APR 2011
