Installation Guide

ManualsBrandsDeckoRail ManualsLumber & Composites3 in. White Offset Aluminum Handrail Bracket

Secondary Handrail Installation Instructions – Page 1

Secondary Handrail Guidelines and Installation

Prior to construction, check with your local regulatory agency

for special code requirements in your area.

Start with an Inside Corner piece when applicable.

Guidelines:

• Theheightofthesecondaryhandrailmustbeinstalledbetween

 34”and38”abovethesurface,regardlessoftheheightoftheguard.

• Werecommendthathandrailsbedrytpriortonalinstallationto

 eliminatecuttingandfasteningerrors.

• IMPORTANT:Thesecondaryhandrailmustbeattachedtoastructural

 support.Wheninstallingmountingbracketsonpostsleeves,ensure

 thehardwareattachestothestructuralsupport.

• Formaximumstrength,bracketsshouldbeusedateverypostand

 everyjoint,orascloselyaspossibletothejoint.

• Anadhesivemaybeappliedtofurtherreinforceconstruction.

• Handrailsmustbesupportedevery6’on-centerbyamountingbracket.

Handrail with Aluminum Insert

Step 1: Drythandrailstodetermineproperlengthspriorto

cuttingrails.

Step 2: Measureandcutrailstoproperlengthsforallruns.

Step 3: Installtohandrailcomponent,followinginstructionsforthe

components.

Tools Required

• Drill

• Miter/CircularSaw

• QuickClamps

• PVCCleaner

• Pencil

• TapeMeasure

• Level

Hand Rail Parts.ai

EndCap

90˚OutsideCorner

180˚PostReturn

HandicapLoop

StraightAluminumWallMount90˚PostReturn

AluminumBracket

(LinePostMountingBracket)

InsideCorner

MountingBracket

HandrailwithAluminumInsert

AluminumJoinerKitAdjustableJoiner

32˚StairElbow

34˚StairElbow36˚StairElbow

5˚HandicapElbow

90˚InsideCorner13.5”WallReturn

Handrail Componentsd

90° Inside Corner

Step 1:Measure2”lessthanthehandrailheighttodetermine

insidecornerbracketposition.Markpost.

Step 2:Alignthetopofthebracketmountingplatewiththemark

madeinStep1.Drill5/32”pilotholesandattachtothepost

usingthe1-1/2”screwsprovided.

Step 3:Alignthe90°insidecornersothatitiscenteredevenlyon

thebracket,ensureitislevel,andclampintoplace.Drill3/16”

pilotholesandsecurewith1”screwsprovided.

Step 4:Slidealuminumjoinersintoeachsideofcorner.Slidejoin-

ersintohandrailsandfollowinstructionsfor“AluminumJoiner

Kit.”

2 2

90°InsideCorner3.ai

Aluminum Bracket (Line Post Mounting Bracket)

Step 1:Measure2”lessthanthehandrailheighttodetermine

bracketposition.Marksurface.

Step 2:Alignthetopofthebracketmountingplatewiththemark

madeinStep1.Drill5/32”pilotholesandattachtothedesired

surfaceusingthe1-1/2”screwsprovided.

Step 3:Clamphandrailtobracketatappropriatelocationto

secureinplace.

Step 4:Drill3/16”pilotholesandattachhandrailusingthe1”

screwsprovided.

AluminumBracket.ai

Summary of content (9 pages)

PAGE 1
Secondary Handrail Guidelines and Installation Tools Required • Pencil • Tape Measure • Level • • • • 90° Inside Corner Drill Miter/Circular Saw Quick Clamps PVC Cleaner Handrail Componentsd End Cap 90˚ Outside Corner 180˚ Post Return 90˚ Post Return Step 1: Measure 2” less than the handrail height to determine inside corner bracket position. Mark post. Step 2: Align the top of the bracket mounting plate with the mark made in Step 1.
PAGE 2
Adjustable Joiner Handicap Loop Step 1: Measure the angle needed. Adjoin the two joiner halves together by inserting the bolt. Place the joiner halves at the desired angle, and tighten bolt to set. Step 2: Cut handrails at ½ the desired angle. Slide handrails onto adjustable joiner. Step 3: Drill 3/16” pilot holes and fasten handrails together using 3/4” screws. Step 1: Position handicap loop in desired location. Mark and cut loop as necessary.
PAGE 3
Straight Aluminum Wall Mount 180° Post Return Step 1: Slide aluminum wall mount into handrail. Step 2: Drill 5/32” pilot holes into desired surface and attach wall mount using 1-1/2” screws provided. Step 3: Drill 3/16” pilot holes into handrail and attach using 3/4” screws provided. Step 1: Position post return in desired location. Mark and cut as necessary. Step 2: Attach post return to handrail system using aluminum joiner.
PAGE 4
Directives de rampes secondaires et installation Outils requis • Crayon • Ruban à mesurer • Niveau • • • • Perceuse Scie circulaire/onglet Pinces rapides Nettoyant de PVC Composants de rampesd Capuchon d’extrémité Coin extérieur de 90° Coude de poteau de 180° Coude de poteau de 90° Coin intérieur de 90° Étape 1 : Mesurez 2 po de moins que la hauteur de la rampe pour déterminer la position de la fixation du coin intérieur. Marquez le poteau.
PAGE 5
Raccord ajustable Boucle handicap Étape 1 : Mesurez l’angle voulu. Joignez les deux moitiés du raccord ensemble en insérant le boulon. Placez les deux moitiés du raccord à l’angle voulu et resserrez le bouton pour installer. Étape 2 : Coupez les rampes à 1/2 de l’angle voulu. Glissez les rampes dans le raccord ajustable. Étape 3 : Percez des avant-trous de 3/16 po et attachez les rampes ensemble en utilisant les vis de 3/4 po. Étape 1 : Placez la boucle handicap à l’emplacement voulu.
PAGE 6
Montage mural droit d’aluminium Coude de poteau de 180° Étape 1 : Glissez le montage mural d’aluminium dans la rampe. Étape 2 : Percez des avant-trous de 5/32 po dans la surface voulue et fixez le montage mural en utilisant les vis de 1 1/2 po fournies. Étape 3 : Percez des avant-trous de 3/16 po et attachez en utilisant les vis de 3/4 po. Étape 1 : Placez le coude de poteau à l’emplacement voulu. Marquez et coupez au besoin.
PAGE 7
Guía e instalación de pasamanos secundario Herramientas necesarias • Lápiz • Cinta métrica • Nivel • • • • Taladro Inglete/Sierra circular Abrazadera Quick Limpiador de PVC Componentes del pasamanosd Tapa final Esquina exterior de 90° Retorno de poste de 180° Retorno de poste de 90° Esquina interior de 90° Paso 1: Medir 2 pulgadas menos que la altura del pasamanos para determinar la posición del soporte en la esquina interior Marque el poste.
PAGE 8
Conector ajustable Paso 1: Medir el ángulo deseado. Unir las dos mitades del conector insertando el perno. Colocar las mitades de los conectores en el ángulo deseado y apretar el perno. Paso 2: Cortar los pasamanos a la mitad del ángulo deseado. Deslizar los pasamanos sobre el conector ajustable. Paso 3: Taladrar orificios de 3/16” y asegurar los pasamanos con tornillos de 3/4”. 1 2 2 Asa para discapacitados Paso 1: Coloque el asa en el sitio deseado. Marque y corte la asa cuanto sea necesario.
PAGE 9
Montaje de pared para tramo recto de aluminio Retorno de poste de 180° Paso 1: Deslizar el montaje de pared dentro del pasamanos. Paso 2: Taladrar orificios piloto de 5/32” en la superficie deseada y unir el montaje de pared con los tornillos de 1-1/2” proporcionados. Paso 3: Taladrar orificios piloto de 3/16” en el pasamanos y unir con los tornillos de 3/4” proporcionados. Paso 1: Colocar el retorno de porte en la ubicación deseada. Marque y corte cuanto sea necesario.