Instructions / Assembly

ManualsBrandsDeckoRail ManualsDeck & Porch Railings6 ft. Western Red Cedar Stair Railing Kit with Black Aluminum Balusters

Measure the distance between posts and, if necessary, cut the

2x4 rails to size by trimming the unnotched end. The baluster

and rails have been set to 34 degrees, so if you need to cut

the rails and cap rail, cut them to the 34 degree angle (fig. 2).

Cut the cap rail at the same end as the rails.

Place the moulded cap rail upside down on a flat surface.

Next, place the top 2x4 rail with the notch on the same side

as the baluster holes into the moulded cap rail channel so that

the holes are facing up. Starting from either end, fasten the

rails together using the (7) 4" screws through holes 1, 2, 5, 8,

11, 14 and 15. If rails are trimmed, predrill any additional holes

with a 1/8" drill bit and insert the screw into the next nearest

hole (fig. 3).

Attach the (4) 2x4 DeckoRail railing brackets according to the

included instructions.

Items you will need

• Drill/power screwdriver

• Miter or circular saw

with carbide-tipped blade

• Tape measure

• Carpenter’s level

• Carpenter’s pencil

• Safety glasses/goggles

• Gloves

Planning your project

Step 1

Assembled in the USA with balusters from Mexico. UFP Windsor, LLC 15 East Walnut St., West Building, Windsor, CO 80550 7734_1/16

DeckoRail.com

Railing Brackets (4)

Baluster

Outside Edge of Stairs

Post

Cap

Less than 6"

Less than 4"

Support Block

34" < Tread Nose to

Top of Rail < 38"

Top and

Bottom Rail

•

StairsOutline3a1.ai

ﬁg. 1

Cut This End

Do NOT Cut This End

Notch

StairRail1.ai

34°

ﬁg. 2

The stair railing was designed to work on stairs that have a 10"

run and 6-3/4" rise, which creates a 34-degree angle. Check local

building code requirements prior to starting your project. A 6" ball

cannot pass through the triangle formed by the bottom rail, tread

and riser. Stair rails are commonly required to be more than 34"

and less than 38" from the tread nose to the top of the rail (ﬁg. 1).

Step 2

Cap

123 456789101112131415

StairRail2.ai

Insert Rail

•

Step 3

ﬁg. 3

STAIR RAILING WITH ALUMINUM

BALUSTERS - INSTALLATION INSTRUCTIONS

Summary of content (6 pages)

PAGE 1
STAIR RAILING WITH ALUMINUM BALUSTERS - INSTALLATION INSTRUCTIONS Items you will need • Drill/power screwdriver • Carpenter’s level • Miter or circular saw with carbide-tipped blade • Carpenter’s pencil • Tape measure • Gloves fig. 1 • Railing Brackets (4) • 34" < Tread Nose to Top of Rail < 38" • Safety glasses/goggles Post Cap • • • • Planning your project • The stair railing was designed to work on stairs that have a 10" run and 6-3/4" rise, which creates a 34-degree angle.
PAGE 2
INSTALLATION INSTRUCTIONS Step 4 fig. 4 Attach the bottom 2x4 rail, with the holes facing up, using the 2x4 DeckoRail railing brackets. Insert the balusters into the pre-drilled holes (fig. 4). Cap Rail Step 5 • Attach the cap rail by aligning the holes to the baluster at one end of the rail and working your way to the opposite end, ensuring that all of the balusters are secured between the two rails (fig. 4).
PAGE 3
RAMPE D’ESCALIER AVEC BALUSTRES EN ALUMINIUM - INSTRUCTIONS D’INSTALLATION Articles dont vous aurez besoin fig.
PAGE 4
INSTRUCTIONS D’INSTALLATION Étape 4 fig. 4 Attachez la rampe inférieure de 5,1 cm x 10,2 cm (2 po x 4 po) avec les trous faisant face vers le haut, à l’aide des supports de rampe d’escalier DeckoRail de 5,1 cm x 10,2 cm (2 po x 4 po). Insérez les balustres dans les trous prépercés (fig. 4).
PAGE 5
RIEL PARA ESCALERA CON BALAÚSTRES DE ALUMINIO - INSTRUCCIONES DE INSTALACIÓN Elementos que necesitará • Taladro/destornillador eléctrico • Sierra circular o angular con disco con puntas de carburo • Nivel de carpintero • Cinta de medir • Guantes fig. 1 • Soportes de rieles (4) • • Lápiz de carpintero 86.4 cm 96.
PAGE 6
INSTRUCCIONES DE INSTALACIÓN Paso 4 fig. 4 Fija el riel inferior de 2x4, con los orificios hacia arriba, usando los soportes del riel DeckoRail de 2x4. Inserta los balaústres en los orificios pretaladrados (fig. 4). Tapa de riel Paso 5 • Fija el pasamanos alineando los orificios al balaústre en un extremo del riel y continuando hacia el extremo contrario, asegurándote de que todos los balaústres queden fijos entre los dos rieles (fig. 4).