Instructions / Assembly

ManualsBrandsDeckoRail ManualsDeck Parts & AccessoriesDeck Railing Table Hardware Kit

Tools Needed

Drill/power screwdriver

Miter or circular saw with carbide tip blade

Tape measure

Carpenter’s pencil

Safety goggles

Gloves

Installation Instructions

Note: The table frame was designed to install with (3) 5-1/2" deck boards or 1x6

boards. Other materials may be used as desired. We recommend using materials

that would be suitable for use as an exterior table.The hardware can support a table

up to 60" long.

Step 1

Cut the table top materials to length. Arrange the (3) boards on a flat surface so that

they are flush with one another.

Step 2

Place both “H” frames on the width of the table top equally spaced apart. Secure

the frames to the underside of the table top using the included screws. Additional

screws may be needed depending on the top material chosen. If desired, add a

vertical ledge or lip to the back of the table to help keep objects from falling off.

Step 3

Place the elbow over the top of the railing and allow it to rest on the railing.

Position the clamp on two balusters and tighten with the hand knob until firmly

installed. Repeat for other elbow, spaced to roughly match the frame spacing.

Note: For taller rails, the hand knob and half of the clamp nearest the deck may

need to be removed to clear the railing. Reinstall the clamp and knob, and tighten.

Items Included

RAIL TABLE HARDWARE KIT

INSTALLATION INSTRUCTIONS

Items Included

(2) Metal “H” frames

(2) Metal elbows

(2) Thumb screws

(24) Screws

table rail kit.ai

Step2.ai

Step3a.ai

Step3b.ai

Step3c.ai

Step 2

Step 3

Tall Rail

Summary of content (4 pages)

PAGE 1
RAIL TABLE HARDWARE KIT INSTALLATION INSTRUCTIONS Tools Needed Items Included Drill/power screwdriver Miter or circular saw with carbide tip blade Tape measure Carpenter’s pencil Safety goggles Gloves (2) Metal “H” frames (2) Metal elbows (2) Thumb screws (24) Screws Installation Instructions Note: The table frame was designed to install with (3) 5-1/2" deck boards or 1x6 boards. Other materials may be used as desired. We recommend using materials that would be suitable for use as an exterior table.
PAGE 2
Step 4 Lift the table into position, and then slide it into the slots on the elbows. Tighten the thumb screw on the bottom of each elbow to secure frames in place. Note: The offset crosspieces on the frame allow the table to be installed so it extends more towards the center of the deck for more of a ledge, or further away from the deck, depending on your use. WARNING! • Maximum weight capacity is 50 lbs uniformly distributed. Do not exceed.
PAGE 3
JUEGO DE HERRAMIENTAS DE MESA DE BARANDAL INSTRUCCIONES PARA LA INSTALACIÓN Herramientas necesarias Destornillador/taladro eléctrico Sierra ingletadora o circular con hoja de puntas de carburo Cinta métrica Lápiz de carpintero Lentes de seguridad Guantes Artículos incluidos (2) monturas de metal “H” (2) codos de metal (2) tornillos de muletilla (24) tornillos Instrucciones para la instalación Nota: La montura de la mesa se diseñó para la instalación de (3) tablas de terraza de 5-1/2 o tablas de 1x6.
PAGE 4
Paso 4 Levante la mesa hacia la posición y luego deslícela en las ranuras de los codos. Ajuste el tornillo de muletilla sobre el fondo de cada codo para asegurar las monturas en el lugar. Nota: Los travesaños inclinados permiten la instalación de la mesa, por eso se extiende más hacia el centro de la cubierta, para más de una repisa o más lejos de la cubierta, dependiendo de su uso. ¡ADVERTENCIA! • La capacidad de peso máximo es de 50 libras distribuidos uniformemente. No lo exceda.