Installation Guide

ManualsBrandsDeckorators ManualsComposite Deck BoardsTropics 12.08-ft Hana Brown Composite Fascia Deck Board

On the other side of the board, place a hidden

fastener into the slot and center on the joist

(figure 3). Install a #7, 1-5/8" stainless steel

screw at a 90° angle through the fastener and

drive flush. Do not over-tighten. The fastener

wings must remain level with the joist for the

next board to fit correctly (figure 4). Install one

fastener at each joist location. Slide the next

board into place so the wings on the previous

fasteners fit into the slot on the side of the

board. Make sure the side gap between the

boards is 1/4".

To keep the interior boards from moving over

time, we recommend pinning the boards at the

center of their length using a #7, 1-5/8" stain-

less steel screw. This holds the deck board in

place at the center

of each board and

allows the decking

to expand/contract

at the ends of the

boards. Pre-drill in

the slot of the deck

board with an 1/8"

drill bit (inset of fig-

ure 5). Drive screw

into the slot so it’s

flush with the bottom

of the groove (figure

5). This will allow

you to properly fit a

hidden fastener into the slot. Install hid-

den fastener clip over the screw and

centered over the joist. Fasten using a #7,

1-5/8" stainless steel screw at a 90° angle

through the hidden fastener and drive flush

with the clip (figure 6). The fastener wings

must remain level with the joist for the next

board to fit correctly (figure 4).

Install one fastener at each joist location along

the length of the board. For installations where

deck boards are butted end-to-end at the joist,

we recommend adding an 8" block and using

a hidden fastener clip at the end of each

board (figures 7 and 8). Be sure to gap the

boards as previously described. Repeat the

process for each board until the outside edge

of the final board is fastened with screws.

Use fascia to conceal the board profile and

inhibit board movement over time. If no fascia

is being used, the entire perimeter of the deck

should be fastened to the rim joist with screws.

Use two fasteners at the end of each board.

These screws will be inconspicuous once the

railing is installed.

Apply these same principles when installing

stair treads.

TIPS FOR SLOTTED DECKING INSTALLATION, CONTINUED

If desired, the board profile

may be concealed with fascia.

joist

deck boards

rim joist

fascia

screw

figure 3

Warning.eps

figure 4

Fig.4.eps

Fig. 5.eps

figure 6

figure 7

Color variation: Most composites will have color variations from piece to piece. This is due to naturally occurring variations in wood fibers and polymers. Purchasing all required decking material at one time

is recommended, as manufacturing runs can produce slightly different colors. Do not install if color variation is not acceptable. Composite Decking will lighten over time, and color variation is not covered by the

warranty. This color-tone shift is dependent upon exposure to sunlight and other environmental factors, and is generally completed in 60 to 90 days. Gray products may turn a light brown before changing to

lighter gray. Preventing mold and mildew growth on composite decking: Mold and mildew can be a nuisance on any exterior building surface, regardless of the material. If the conditions are right, they

will spawn on wood, plastic, concrete, metal and other surfaces. Mold formation is most prevalent in consistently wet, shaded areas. Spores from the natural environment are carried by the wind and commonly land

on decks surfaces. It is important to note that the appearance of mold/mildew is a function of nature, not necessarily a deficiency with any of the material on which it grows. Cleaning: Periodic washing with soap/

detergent and water will help remove surface dirt. This will also help prevent the buildup of pollen, debris and spores that can cause and accelerate mold/mildew growth. CAUTION: A pressure washer should not

be used to “blast” mold/mildew or soils from a deck surface. The abrasive nature of the water stream can potentially damage the material by driving the spores into the material, which may create a more challenging

problem to remediate. A pressure washer with a fan-tipped nozzle should be used only to lightly wet or rinse wood or composite deck surfaces. There are many deck wash and exterior cleaning products available at

retail. It is important to make sure you use a cleaner specifically intended for your application. After selecting a product, be certain to read, understand and follow all instructions supplied by the manufacturer. Some

cleaning products and inhibitors may be more effective than others, depending on the environmental conditions your deck is subjected to. Additionally, it is always a good idea to test the cleaner in a small, inconspicuous

area prior to applying it to the entire deck. Mold inhibitors: As with deck washes, there are several mold-inhibitor products available from paint stores, hardware stores, online outlets and home centers to help

prevent long-term mold/mildew growth. For any product selected, be certain to read, understand and follow all instructions provided by the manufacturer. Depending upon the environmental factors affecting your

deck, some preventive cleaning products may be more effective than others. It may be necessary to try more than one product. For ongoing preventive maintenance, follow the manufacturer’s recommendation.

Composite Decking is not suitable for structural use. It should not be used for primary load-bearing members such as posts, joists, beams or stringers. The same common-sense precautions should be taken when

handling Composite Decking as with wood or other building materials. Dust masks and eye protection devices are recommended to avoid possible irritation from sawdust and chips. Gloves will help to protect

the hands. Hands should be washed after doing construction work. The diagrams and instructions in this brochure are for illustration purposes only and are not meant to replace a licensed professional. Any

construction or use of the product must be in accordance with all local zoning and/or building codes. The consumer assumes all risks and liability associated with the construction or use of this product. The

consumer or contractor should take all necessary steps to ensure the safety of everyone involved in the project, including, but not limited to, wearing the appropriate safety equipment. EXCEPT AS CONTAINED IN

THE WRITTEN LIMITED WARRANTY, UNIVERSAL CONSUMER PRODUCTS, INC., DOES NOT PROVIDE ANY OTHER WARRANTY, EITHER EXPRESS OR IMPLIED, AND SHALL NOT BE LIABLE FOR ANY DAMAGES, INCLUDING

CONSEQUENTIAL DAMAGES.

Fig.2.eps

figure 5

Fig.1.eps

Fig. 7.eps

figure 8