Before returning this product to the store of purchase Contact Dee Zee if you experience the following problems: • Missing Parts • Installation Problems/Questions • Warranty Questions 1.800.779.2102 Hours of operation: 8am - 5pm CST, Mon-Friday Review complete warranty policy and register your product at: www.deezee.
Dee Zee Running Board Installation Instructions Congratulations on your purchase of a quality Dee Zee product. Dee Zee is recognized as having the highest quality running boards and accessories on the market today. We have earned this reputation by offering our customers a product they can be proud to place on their vehicles. Dee Zee meets all the criteria of manufacturing a custom-fit product which guarantees it to be the easiest product to install.
Dee Zee FX Running Board Installation Instruction FX 31927, FX 31327, FX 31928, FX 31328, FX 31929, FX 31329, FX 31930, FX 31330 (2009 - Current) Dodge Ram Regular, Quad, Mega & Crew Cab RUNNING BOARD A B E F I C LH BRACKET G REG CAB X1 REG CAB VARIES PN 685 X2 PN 686 1/4" FLAT WASHER 1/4" HEX NUT J K X8 REG CAB X8 X12 PN 71 X12 PN 97B 8mm THREADED #10 X 5/8" BLACK PLATE PHILLIPS HEAD SCREW MUD FLAP D REG CAB X2 REG CAB X2 MXFLSL X2 B 2008RP X3 B 2008LP X3 MXFLSR BULB GASKET NUTSERT SET TOOL
TOOLS REQUIRED WRENCH/RATCHET 3/8", 7/16" 13mm, 15mm TIN SNIPS 1 1/8" DRILL BIT Place the bulb-seal gasket [E] onto the backlip of the runing board [A]. Cut the bulb-seal gasket with tin snips so that it is flush with the ends of the board FOR REGULAR CAB: Slide two 1/4 x 3/4" slotted hex head bolts [P] into both of the bolt channels on the bottom side of the running board.
2 Place the end cap [O] onto the running board as shown below. The image shown is the drivers side side box board. Secure the end cap in place using a phillips head screwdriver and two 1/4 x 1" black phillips head round head screws [L]. 3 Place the mud flap [D] onto the running board as shown below. The image shown is the drivers side side box board. Secure the mud flap in place using a 3/8" socket or wrench and one black sheet metal screw [K].
4 Locate the hexagon shaped holes on the inside of the rocker panel. There will be two holes at each mounting location. The passenger side is shown below. Insert an 8mm nutsert [G] at each location. The front of the vehicle is to the left of the picture. The regular cab will not have a middle mounting location.
5 Use the nutsert set tool [F] to crimp the nutserts in the holes. Hold the nut on the set tool with a 15mm wrench. Tighten the bolt in the set tool with a 13mm socket. Torque the nutserts to the spcification below to insure they are set correctly. 6 Put a 8mm x 25mm bolt [H] through the top hole in the brace [B] and thread into the 8mm threaded plate [M] until the bolt starts to come through the threaded plate. Repeat this for the other braces.
7 When the brace is put up to the vehicle mounting location, the threaded plate must go into the large slot above the nutserts previously installed. Thread 2 of the 8mm x 25mm bolts [H] through the slots in the braces into the nutserts. Only engage the bolts a few threads into the nutserts. Do NOT tighten at this time. Repeat this step at the other two brace mounting locations.
8 Remove and discard the small cladding located in front of the front door. 9 Align the bolt in the channels on the bottom of the running with the slots in the braces and insert the bolts into the slots. Attach the running board to the braces using the 1/4" flat washers [I], and the 1/4" hex nuts [J]. The flap should be located against the wheel well. This step continued on the next page.
Place the running board on the braces with the bulb seal up against the rocker panel. The back lip of the board must sit on the outside of the rocker panel. 10 Push up on the brace to put tension on the threaded plate in the large slot. Tighten the bolt with the threaded plate using a 13mm socket. Air tools are recommended for this. After the bolt with the threaded plate is tightened, tighten the remaining two 8mm bolts.
Align the board with the vehicle and make sure that the mud flap is up against the wheel well. Once the board location is set, use a 7/16" socket/wrench to tighten the nuts attaching the board to the brace. 12 Align the flap with the wheel well and drill three 1/8" holes through the mudflap and the sheet metal of the inner fender well. On the bottom of the board drill a 1/8" hole through the end cap into the board.
13 Attach the mudflap using four #10 screws [N]. Check to insure that all hardware has been tightened. Repeat process for other side of vehicle.
