DBOARD R2 PVH – Technical Operation Manual DBoard R2 BY APPROV. REV. DATE REASON OF ISSUE BF OC A1 11/2018 DOCUMENT CREATION CM BF A2 08/2020 UPDATE BF BF A3 09/2020 Operation temperature clarification and labeling explanation. Restructure the information.
INDEX 1. Introduction ............................................................................................................................................. 3 1.1. Glossary ................................................................................................................................................ 3 2. Safety information ................................................................................................................................... 3 2.1.
1. Introduction The purpose of this manual is to describe the main characteristics, installation and operation procedures for the Drive Board 3.1 Tracker Controller. It is required that the Installer adheres to these instructions to ensure correct installation. For an in depth understanding detailed manuals for each of the main components are available. 1.1. Glossary Term Tracker (or solar tracker) DBOARD Emergency Stop 2.
2.4 Installation Risks Concerning errors during the installation of the equipment: • If the DBoard is supplied with inverse polarity: The device integrates input reverse polarity protection, but a continued exposure to reverse polarity may break the input protection. The cables are differenced by two colors to help minimize the chances of error (red and black). 2.
3. DBoard overview BACK VIEW FRONT VIEW 5 This document and the information in it are provided in confidence, for the sole purpose of exploring business opportunities between the disclosing party and the receiving party. Confidential document. It is not allowed to reproduce or disclose partial or totally the information contained in it, except by express written consent of Deeptrack.
3.1. Connectors and signals – Interfaces 1. LoRa interface: LoRa embedded Antenna and footprint for external antenna connector (UMC) Through the LoRa antenna interface, the user can communicate LoRa devices. The board includes an optional connector for install an external antenna. 2. Multipurpose connector footprint (GPIO) and external multipurpose connector (B3) The multipurpose connector is integrated as a discrete component and connected to the isolated interface, 24VDC .
3. Power and motor drive connector Power supply input and SSR outputs. Connector SPT 2.5/4-V-5.0. Connector SPT 2.5/4-V-5.0. The board must be 24VDC powered. Located in the same connector are the outputs for motor driver (M1 and M2), 24VDC, up to 15A. Signals: • • • • 24V GND M1 M2 4. ISO RS485 Connector Isolated RS485 interface. Connector PTSM 0,5/ 3-HV-2,5. For devices which does not need power from the board and are powered from another voltage source Signals: • • • ISO B GND ISO A 5.
7. Led interface Several LEDs are used to indicate the status of the board. All the LEDs are programmable, except LED “PWR” which is directly connected to the power supply. Signals: • • • • • Power on RF - RF activity DRV - Driver enabled ACT - Program running ERR - Error/Emergency reporting 8. SPI Bus connector Serial Peripheral Interface. Connector PTSM 0,5/ 6-HV-2,5 Signals: • • • • • • S1 S0 SCK nCS GND 3V3 9.
4. Installation instructions 4.1. Power the DBoard WARNING Equipment intended to build in without enclosure. Additional means shall be provided in order to protect user against mechanical, thermal, and electrical shock risks. It shall be evaluated at the final installation. WARNING The board should not be connected while the power supply is on. The DBOARD is powered through one SPT 2.5/4-V-5.0 connector in the left lower part of the board.
6. Data 6.1. Manufacturer data DEEPTRACK, S.L.U. C/ Avenida de la Transición Española, 32, Edificio A, Planta 4 28108 - ALCOBENDAS (Madrid) - ESPAÑA CIF: B-85693224 Telephone: +34 91 831 00 13 6.2. Equipment data 7. TYPE OF EQUIPMENT Tracker controller EQUIPMENT NAME DBOARD R2 MODELS R2 Markings The label of the board will be printed on circuit, an additional label will be added in production with the serial number. Commercial brand info.
NFC compliant label DBOARD fully complies the requisites to include the NFC logotype so it is included over the NFC patch. 8. FCC/ISED Regulatory notices Modification statement DEEPTRACK S.L.U. has not approved any changes or modifications to this device by the user. Any changes or modifications could void the user’s authority to operate the equipment. DEEPTRACK S.L.U. n’approuve aucune modification apportée à l’appareil par l’utilisateur, quelle qu’en soit la nature.