PRODUCT MANUAL V 1.1 usa@deerc.com (USA) eu@deerc.com (EU) +1(855) 777-8866 jp@deerc.com (JP) www.deerc.
< PREFACE > To make your experience with this remote control car as easy and convenient as possible, please read the instructions provided before using the product. Enjoy and have fun with the product while keeping the manual for future maintenance and reference. 1. In order to protect the legitimate rights and interests of users, please be sure to carefully read the contents of this manual before using this product. 2.
< PACKAGE CONTENTS > RC Helicopter Remote Control USB Charging Cable Top B propeller Lower A propeller Tail propeller RC Helicopter Battery Product Manual < REMOTE CONTROL FUNCTIONS > Power switch Landing(press once) Left trim Emergency stop(press and hold) Right trim Take Off Ascend and Descend Forward/Reverse Rotate left/right Lights on/off No function No function Speed switch Power Indicator
< HELICOPTER’S DETAILS > ① Balancing rod ⑤ No function ② Top B propeller ⑥ Landing gear ③ Lower A propeller ⑦ Power switch (”I” means on, “0” means off) ④ Tail propeller ⑧ RC helicopter battery
< CHARGING > When the helicopter runs out of power, the helicopter's power indicator will flash. Please stop flying, power down and remove the battery. USB Adapter (5V @ 0.5-2.0A) Power Bank Computer USB Port 1. Plug the USB charging cable into the USB charging port of the computer, power bank or USB adapter (5V@ 0.5~2.0A). 2. Plug the USB charging cable into the charging port. 3. Charging time: about 60 minutes. 4.
< BATTERY INSTALLATION > 1. Remote’s Battery 3 x 1.5V AAA (Not included) ① Unscrew and open the battery cover. ② Insert 3 AAA batteries in the correct direction. ③ Close the battery cover and lock it. ① If the remote will not be used for a long time, make sure to turn it off and remove the batteries. ② When the remote runs out of power, the remote's power indicator will flash. 2. Helicopter’s Battery Push the battery into the bottom battery compartment of the helicopter in the correct direction.
< OPERATION > 1. Pairing Once batteries are inserted to the helicopter and the remote ① Turn on the power switch of the helicopter, the power indicator of the helicopter will flash quickly. Then Keep the helicopter on level. DO NOT hold it in your hands. ② Turn on the power switch of the remote, you will hear the “Di” sound and the power indicator of the remote will flash. ③ Push the left joystick up then down to pair with the helicopter.
< OPERATION > 3. Ascend, Descend, Forward, Reverse, Left Rotate and Right Rotate Push the left joystick forward, the helicopter will ascend. Push the left joystick reverse, the helicopter will descend. Push the right joystick forward, the helicopter goes forward. Push the right joystick reverse, the helicopter goes reverse. Push the right joystick to the left, the helicopter will rotate to the left. Push the right joystick to the right, the helicopter will rotate to the right.
< OPERATION > 4. Lights Switch and Speed Switch Lights on/off Speed switch Press the lights switch button once to turn on or off the power indicator of the helicopter. Press the speed switch button once to switch the speed of the helicopter. The remote will switch at a fast speed when you hear the “Di Di” sound, and the remote will switch at a slow speed when you hear the “Di” sound. 5.
< FAQ > QUESTIONS The remote doesn't work The helicopter's out of control The chopper can't ascend CAUSE SOLUTIONS Batteries installed improperly Insert batteries in the correct direction Battery's dead Replace the batteries Failure to pair between helicopter and remote Both rebooting.
< INTRODUCTION OF PARTS > Helicopter Shell A and B Propeller Balancing Rod Assembly Lower Propeller holder Main Motor Drive shaft Landing in Gear Tail Motor Assembly Receiving Circuit Board Battery ry Remote Control USB Charging Cable Frame Drive Tube
< WARNINGS > Flying in the open Within your Fly Below sight 32 feet (10 m) ----------------------------------------------------------- Avoid flying over or near obstacles, crowds, high voltage power lines, trees, airport or bodies of water. ----------------------------------------------------------- DO NOT use the drone in adverse weather conditions such as rain, snow, fog and strong wind. ----------------------------------------------------------Stay away from the rotating propellers and motors.
< WARNINGS > 1. According to the instructions provided on the manual. Some part needs to be assembled and adjusted by adults. 2. Please use under the guidance of an adult. 3. Please promptly put away the packing materials so as not to cause harm to children. 4. Do not operate on a location where water is trapped or under the rain. Parts of the product may malfunction if exposed to water. 5. Do not touch the rotating wheel to avoid injury. 6.
19. Non-rechargeable batteries cannot be charged. 20. When charging a rechargeable battery, adult supervision is required. 21. The rechargeable battery should be removed from the toy before charging. 22. Do not mix old and new or different types of batteries. 23. Only use the USB cable configured by this product when charging the battery. 24. Do not disassemble the battery or modify the battery to avoid risk of fire or explosion. 25.
< GENERAL INFORMATION > FCC Notice: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
RF Exposure (This Statement is for the aircraft section only) The equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This device should be installed and operated with minimum distance 20cm between the radiator & your body. IC Notice: This device complies with Canada Industry licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference; and (2) this device must accept any interference.
6. Never charge on a flammable surface, near flammable products or inside a vehicle (perferably place the battery in a non-flammable and nonconductive container). 7. Never leave the battery unattended during the charging process. Never disassemble or modify the housing’s wiring, or puncture the cells. Always ensure that the charger output voltage corresponds to the voltage of the battery. Do not overcharge the batter that may cause short circuit. 8.
MANUFACTURER INFORMATION Manufactured by Xiamen Huoshiquan Import & Export CO., LTD Room 703,No. 813-2 Xiahe Road, Siming District, XIAMEN, China Please do not hesitate to contact us if you need further support. usa@deerc.com (America) eu@deerc.com (Europe) jp@deerc.
