Installation Guide
16寸涡旋扇 145*210MM
16" TURBO DRUM FAM
ITEM NO.: FAN-TD16
120V / 60Hz, 1.35A
1. Grasp plug and remove from the receptacle or other outlet device. 1. Place the fan on a safe, flat surface where it can not fall or be pulled by the
cord.
2. Loosen the adjustment knobs (C) on each side of the fan by turning
counterclockwiseand tilt the fan head (A) to the desired angle. Tighten the
adjustment knobs(C) by turning them clockwise. WARNING: Do not move or
adjust fan while in operation.
3. Plug the power cord into electrical outlet.
4. Select preferred speed by rotating the switch on the back of fan.
Please choose low speed for lower noise, high speed for large air volume.
5. Always turn off (0-Off) and unplug fan after using.
Unplug the appliance before celaning.Don't use any water for celaning metal
surfaces.Slightly moisten a cloth and the wipe off the surfaces of the fan.In order
to remove the dust from the grill,use a vacuum cleaner or remove the front grill
by removing the securing screws on the edge of the grill.After cleaning, remount
the grill.After doing this,fasten the screws on the edge of the grill.
Do not unplug by pulling on cord.
2. Open fuse cover. (See Fig.2)
3. Remove fuse carefully. (See Fig.3)
4. Risk of fire. Replace fuse only with 5Amp, 125Volt fuse. (See Fig.4)
5. Close fuse cover. (See Fig.5)
1. Position a rubber pad (D) between the fan head (A) and one side of the stand
(B), aligningthe rubber pad (D) with the predrilled holes.
Wall-Mount Instruction
2. Secure the stand (B) to the fan head (A) by inserting an adjustment knob (C)
through the stand (B), rubber pad (D), and into the fan head (A). Repeat for
the other side of the fan.
Mount fan on a wooden wall only.
This fan is recommended to be mounted by a qualified electrician.
To reduce the risk of electric shock and personal injury, ensure the location for
all mounting is able to support this fan.
1 2 3 4
The manufacturer warrants this product to be free from manufacturing defects
in the material and workmanship under normal use for a period of one year after
the date of purchase by the original purchaser.
This warranty does not cover transit damages. This warranty does not apply to
damages from accident, misuse, alteration of any kind to the fan or where the
connected voltage is more than above the nameplate voltage. This warranty
does not apply to the finish on any portion of the product. Servicing performed
by unauthorized persons shall render the warranty invalid. The warranty is not
responsible for damages of any kind, including accident and consequential
damages. Some states do not allow the exclusion or limitation of the incidental
or consequential damages, so the above exclusion or limitation may not apply
to you. This warranty gives you specific legal rights, and you may also have
other rights which vary from state to state.
USER SERVICES INSTRUCTIONS OPERATION INSTRUCTIONS
CARE AND MAINTENANCE
ASSEMBLY INSTRUCTIONS
Fig.2 Fig.3 Fig.4 Fig.5
DESCRIPTIONPART PART #
FAN-TD16
Blade
1
1
C
A
0 - Stop ||| - High || - Medium | - Low
B
F
E
A
B
C
G
D
READ & SAVE THESE INSTRUCTIONS
Questions, problems, missing parts? Before returning the product,
please e-mail our customer service by
hicfm@outlook.com
1. Read and save these instructions. Do not operate fan unless you have
read these instructions.
2. Unplug the fan before moving it or performing maintenance. Do not touch
the fan when your hands are wet.
3. Those who are not qualified electricians should not disassemble, repair or
rebuild the fan.
4. Unplug the fan when it is not in use.
5. DO NOT unplug the fan by pulling the cable cord. Unplug by holding the
plug and pulling.
6. DO NOT use the fan when there is damage to the cable cord or plug. If
the supply cord is damaged, it has to be replaced by the manufacturer,
its service agent or similarly qualified persons.
7. To Reduce The Risk Of Fire, Electric Shock Or Injury To Persons, Do Not
Use Replacement Parts That Have Not Been Recommended By The
Manufacturer (e.g. Parts Made At Home Using A 3D Printer).
8. DO NOT use the fan close to fires.
9. DO NOT insert your hand or other objects into the grille or the movable parts.
10. To reduce the risk of fire or electric shock, do not use this fan with any
solid-state speed control device.
11. DO NOT use this fan outdoors, this fan is designed for indoor use only.
12. To Reduce The Risk Of Fire Or Electric Shock Do Not Use With An
Extension Cord.
1. Unplug the fan from the socket and clean it with a soft cloth.
2. DO NOT immerse the fan.
3. Fit the guard onto fan before starting up the fan.
4. This fan is not intended for use by people (including children) with
reduced physical, sensory or mental capabilities or lack of experience
and knowledge unless they have been given supervision or instruction
concerning use of the fan by a person responsible for their safety.
Supervise children to ensure they do not play with the fan.