82-13110 4 Channel PCI DVR Card Owner's Manual 650 Congress Park Dr Centerville, OH 45459 1-800-543-4330
SuperDVR & TD Series Cards User Manual CONTENTS CONTENTS 1 Introduction .................................................................................................. 1 1.1 Summarization .............................................................................................. 1 1.2 System Requirements ................................................................................... 3 1.2.1 TD3004~TD3216 Series Cards System Requirements .................................................... 3 1.
CONTENTS 4 SuperDVR & TD Series Cards User Manual System Setup ............................................................................................. 29 4.1 Basic Configuration ..................................................................................... 29 4.2 Video Configuration ..................................................................................... 31 4.3 Motion Detection Configuration ................................................................... 32 4.3.
SuperDVR & TD Series Cards User Manual CONTENTS Appendix 2.1.1 Cannot Install the SuperDVR Driver ............................................................... 76 Appendix 2.1.2 Why cannot run SuperDVR at the windows 2003 operate system? ................ 76 Appendix 2.1.3 Can’t find TD series Devices in Device Manager ............................................ 76 Appendix 2.2 How to Use SuperDVR ................................................................ 77 Appendix 2.2.
SuperDVR & TD Series Cards User Manual FIGURES FIGURES Figure2-1 Figure2-2 Figure2-3 Figure2-4 Figure2-5 Figure2-6 Figure2-7 Figure2-8 Figure2-9 Figure2-10 Figure2-11 Figure2-12 Figure2-13 Figure2-14 Figure2-15 Figure2-16 Figure2-17 Figure2-18 Figure2-19 Figure2-20 Figure2-21 Figure2-22 Figure2-23 Figure2-24 Figure2-25 Figure2-26 Figure2-27 Figure2-28 Figure2-29 Figure2-30 Figure2-31 Figure2-32 Figure2-33 Figure2-34 Figure2-35 Figure2-36 Figure2-37 Figure2-38 Figure2-39 Figure2-40 Figure2-41 Figure3-1 Fig
SuperDVR & TD Series Cards User Manual FIGURES Figure4-5 Video Configuration ............................................................................................... 31 Figure4-6 Motion Detection Configuration ............................................................................. 32 Figure4-7 Schedule Configuration ......................................................................................... 33 Figure4-8 Edit Schedule ..............................................................
SuperDVR & TD Series Cards User Manual TABLES Fig 7.14 Camera setup configuration.............................................................................................. 64 Fig 7.15 Schedule configuration ..................................................................................................... 65 Fig 7.16 Alarm configuration ........................................................................................................... 65 Fig 7.17 Record configuration ........................
SuperDVR & TD Series Cards User Manual 1 Introduction 1 Introduction 1.1 Summarization Thank you for choosing our digital video capture cards. 1Channel, 4 Channel, 9 Channel, 16 Channel and 32 Channel cards adopt H.264 compression format, and enable maximum 32 channels real-time or none real-time surveillance. Our cards are mature and cost-effective products that should be your ideal choices.
1 Introduction • SuperDVR & TD Series Cards User Manual Recycling record mode Users can set recording storage sequence for HDD partitions. The recording storage will automatically swap to the next partition when it is full. If all the partitions are full and recycling record mode is enabled, the former recorded data will be covered by new data. Users can also set HDD minimum storage alarm.
SuperDVR & TD Series Cards User Manual 1 Introduction 1.2 System Requirements Our TD series video card support running on Windows VISTA OS. And the computer which connected the TD series video card required that motherboard and VGA card could support Windows VISTA OS. 1.2.
SuperDVR & TD Series Cards User Manual 1 Introduction NOTICE 1.The computer which installed TD3316 video card requires that motherboard and VGA card could support Window VISTA OS. 2.Motherboards listed below which has passed the test can work well with TD3316: • Foxconn 865A01(Intel 865) • Ga-81pe1000-G 865(Intel 865) • Asus P4p800 865(Intel 865) • ASUS P5GD1-VM 915(Intel 915) • MSI 6728 865(Intel 865) • Abit IS7-E 865(Intel 865) • ASUS-P4GPL-X 915(Intel 915) • ASROCK 775I915PL-SATA2 915(Intel 915) 1.2.
SuperDVR & TD Series Cards User Manual • • 1 Introduction NVIDIA Geforce 7600GS NVIDIA Geforce 8500GT If recorded disk partition’s format is FAT32 and the system has run for a long time, the system will create a lot of data fragments that may results in system runs slowly. It’s recommended to make disk defragmenter every 10 to 30 days. We strongly suggest that use NTFS format for record disk partition. 1.2.
SuperDVR & TD Series Cards User Manual 1 Introduction Motherboard VGA card ATI X300 ATI HD2400 ASUS P5L-1394 ATI X300 ATI HD2400 ASUS P5GD1-VM ATI X300 ATI X700 Table1-7 Motherboards and VGA Cards Support VISTA OS 1.2.6 TD4108/ 4308/4408/4408L Cards System Requirements Card Intel PD Dual-core 2.8 G above HDD TD4108,TD4308, TD4408,TD4408L *one card Intel P4 Celeron processor 3.0G minimum 80G minimum RAM 512M minimum 2.
SuperDVR & TD Series Cards User Manual 2 Hardware Installation 2 Hardware Installation 2.1 Video Capture Card Hardware 2.1.
SuperDVR & TD Series Cards User Manual 2 Hardware Installation 2.1.2 TD3304 Card Hardware Figure2-2 TD3304 Video Capture Card Pin Port 1PIN 2PIN 3PIN 4PIN 5PIN 6PIN 7PIN 8PIN 9PIN 10PIN Define Interpret 5V Power Source (5V) ALARM_COM Alarm COM ALARM_NC Alarm Normal Close ALARM_IN1 Alarm Input 1 ALARM_NO Alarm Normal Open ALARM_IN2 Alarm Input 2 GND Ground ALARM_IN3 Alarm Input 3 GND Ground ALARM_IN4 Alarm Input 4 Table2-2 TD3304 Card Pins 2.1.
SuperDVR & TD Series Cards User Manual 2 Hardware Installation Figure2-4 Pins Definitions of TD3008 Video Capture Card 2.1.
SuperDVR & TD Series Cards User Manual 2 Hardware Installation Pin Port Pin17 Pin18 Pin19 Pin20 Define Alarm_out1 Alarm_out2 Alarm_out3 Alarm_out4 Pin Define Port Alarm Output 1 Pin37 GND Alarm Output 2 Pin38 5V Alarm Output 3 Pin39 Not Used Alarm Output 4 Pin40 Not Used Table2-3 Pins Definitions of TD3016 Card Interpret Interpret Ground Power Source (5V) Not Used Not Used 2.1.
SuperDVR & TD Series Cards User Manual 2 Hardware Installation 2.1.6 TD3216 Card Hardware Figure2-10 TD3216 Video Capture Card Figure2-11 Pins Definitions of TD3216 Video Capture Card 2.1.
SuperDVR & TD Series Cards User Manual 2 Hardware Installation P1 17 16 VINch1 1 9 2 10 3 11 4 12 5 13 6 14 7 15 8 VINch2 VINch3 VINch4 VINch5 VINch6 VINch7 VINch8 AGND CONNECTOR DB15 AGND PIN1 Video1 PIN6 Video6 PIN2 Video2 PIN7 Video7 PIN3 Video3 PIN8 Video8 PIN4 Video4 Pin9-pin15 GND PIN5 Video5 Figure2-13 Video Connector and Pins Definition Figure2-14 TD3308 Video Capture Card Alarm Port Pin Port Pin1 Pin2 Pin3 Pin4 Pin5 Pin6 Pin7 Pin8 Pin9 Pin10 Pin11 Pin12 Pin13 Pin14 Pin15 Pin16 Pin17 Pin18 P
SuperDVR & TD Series Cards User Manual 2 Hardware Installation 2.1.
SuperDVR & TD Series Cards User Manual 2 Hardware Installation J3 GiL-G-8P-S3T2-E J4 GiL-G-8P-S3T2-E 1 2 3 4 5 6 7 8 PIN1 VIN-9 1 2 3 4 5 6 7 8 PIN2 GND PIN1 VIN-13 PIN2 GND PIN3 VIN-10 PIN4 GND PIN3 VIN-14 PIN4 GND PIN5 VIN-11 PIN6 GND PIN5 VIN-15 PIN6 GND PIN7 VIN-12 PIN8 GND PIN7 VIN-16 PIN8 GND Figure2-17 Video Pins Definition 2.1.9 TD3101 USB Card Hardware Figure2-18 TD3101 USB Video Capture Card 2.1.
SuperDVR & TD Series Cards User Manual 2 Hardware Installation PC cannot identify USB card. Do not insert two or more USB video capture cards simultaneously. Do not use with the other PCI video capture card simultaneously. 2.1.
SuperDVR & TD Series Cards User Manual 2 Hardware Installation Figure2-22 Multi-Card Connection 2.1.
SuperDVR & TD Series Cards User Manual 2 Hardware Installation PIN6 AUDIO12 PIN16 AUDIO13 PIN7 AUDIO14 PIN17 PIN8 AUDIO15 GND PIN9 AUDIO16 / PIN10 AUDIO1 PIN26 Figure2-24 Audio Connector and Pins Definition J1 GiL-G-8P-S3T2-E 1 2 3 4 5 6 7 8 PIN1 PIN3 PIN5 PIN7 J2 GiL-G-8P-S3T2-E 1 2 3 4 5 6 7 8 VIN-1 PIN2 GND PIN1 VIN-5 PIN2 GND VIN-2 PIN4 GND PIN3 VIN-6 PIN4 GND VIN-3 PIN6 GND PIN5 VIN-7 PIN6 GND VIN-4 PIN8 GND PIN7 VIN-8 PIN8 GND Figure2-25 Video Pins Definition 2.1.
SuperDVR & TD Series Cards User Manual 2 Hardware Installation PIN1 AUDIO2 PIN11 AUDIO3 PIN2 AUDIO4 PIN12 AUDIO5 PIN3 AUDIO6 PIN13 AUDIO7 PIN4 AUDIO8 PIN14 AUDIO9 PIN5 AUDIO10 PIN15 AUDIO11 PIN6 AUDIO12 PIN16 AUDIO13 PIN7 AUDIO14 PIN17 PIN8 AUDIO15 PIN18 PIN9 AUDIO16 PIN10 AUDIO1 PIN19-26 GND Figure2-27 Definition of Audio Connector and Pins 2.1.
SuperDVR & TD Series Cards User Manual 2 Hardware Installation PIN1 VIDEO-1 PIN9 GND PIN2 GND PIN10 AUDIO-1 PIN3 VIDEO-2 PIN11 AUDIO-2 PIN4 GND PIN12 AUDIO-3 PIN5 VIDEO-3 PIN13 AUDIO-4 PIN6 GND PIN14 NULL PIN7 VIDEO-4 PIN15 GND PIN8 GND Figure2-29 Definition of Audio and Video Connector’s Pins When there are some TD4108 cards connect together, please connect the line as following figure.
SuperDVR & TD Series Cards User Manual 2 Hardware Installation 2.1.15 Alarm Board Hardware Figure2-31 Alarm Board Figure2-32 Pins Definition of Alarm Board Connect J2 to PC serial port and you may use alarm board by SuperDVR system. 2.1.16 Connect Audio Signal For TD3004/3008/3016/3304/3116/3216/4104/4108/4408, connect the audio input device to the microphone connector on the motherboard.
SuperDVR & TD Series Cards User Manual 2 Hardware Installation 2.2 Install Video Capture Card Driver STEP1： Run Setup.
SuperDVR & TD Series Cards User Manual 2 Hardware Installation STEP3： Install driver first. Figure2-36 Rate of Progress of Driver Installation STEP4： After this process, it begins to install the application package SuperDVR, as below: Figure2-37 Select Installation Folder STEP5： Select the suitable option, and click ‘Next’. Figure2-38 Register Application STEP6： 22 Click ‘Next’.
SuperDVR & TD Series Cards User Manual 2 Hardware Installation Figure2-39 Driver and Application Installation Finished STEP7： Click ‘Finish’. STEP8： Now, after all the processes are finished, it will create a shortcut on the desktop. Restart the computer and launch the surveillance program. Figure2-40 Shortcut of SuperDVR NOTICE When you install the driver software on Microsoft VISTA system, you need select the option as below figure first.
SuperDVR & TD Series Cards User Manual 3 Main Display Interface 3 Main Display Interface Run SuperDVR program and the main display interface appear as below: Figure3-1 SuperDVR Main Display Interface 3.1 Display Control Panel 3.1.1 Display Control Panel Figure3-2 Display Control Panel Display control panel includes Display Mode buttons and disk free space indicator, ‘Auto Dwell’ button. Every button has its built-in indicator light.
SuperDVR & TD Series Cards User Manual 3 Main Display Interface 3.1.3 Flip Pages When the display mode is 1CH, 4CH, 9CH, 16CH or 32 CH click will display the next page according to the display mode. , system 3.1.4 Auto Dwell Display Mode In case users want to see all the channels in sequence, then click enter Auto Dwell display mode. and 3.1.5 Capture In case users want to capture picture quickly, they can click save 32 pictures to the default folder on disk, c:\ path. , system will 3.1.
SuperDVR & TD Series Cards User Manual 3 Main Display Interface • Manual record mode • Motion Detection record mode • Sensor Alarm record mode Motion Detection record mode and Sensor Alarm record mode are together called as Alarm Record. In case, users use multiple cameras to record, every camera works separately and the record file also saved separately. The parameters, i.e. camera ID, record date/time, and record mode are all saved together with the record file. 3.3.
SuperDVR & TD Series Cards User Manual 3 Main Display Interface 9. Sensor Record Frame Rate If sensors are utilized to trigger recording, users can select record frame rate here. 10. Camera Security The users are divided into three standards: Normal user, Power user and Administrator. By selecting the options, only administrators can see the corresponding channels. 11. Record Quality Select record image quality here. 12. Audio in SuperDVR6.
SuperDVR & TD Series Cards User Manual 3 Main Display Interface 3.3.5 Sensor Alarm Record Mode Users can use sensors to trigger sensor alarm record for relative channels. At that time, the record status indicator light will turn red . 3.3.6 Motion Detection Record Mode It will enable the system to detect image changes and begin to record by activating motion detection and motion alarm record.
SuperDVR & TD Series Cards User Manual 4 System Setup 4 Click System Setup and enter the main setup interface. Figure4-1 Basic Configuration The definitions of the buttons in Figure4-1 are as below: Basic Configuration Schedule configuration Video configuration Motion Detection Configuration Alarm Configuration P.T.Z Configuration User Configuration Save and Return 4.1 Basic Configuration Click and enter the basic configuration page where users can setup the system or just use the defaults.
SuperDVR & TD Series Cards User Manual 4 System Setup Figure4-2 Caption and General Configuration 1. Dwell Interval. If users enable Auto Dwell function in the main interface page, users can set the dwell time of a page here. 2. Caption There are four options, None, ID, Name, and ID/Name for users to select for all the channels. • ‘None’ means no title; • ‘ID’ means camera numbers, i.e. 1, 2, 3 and so on; • ‘Name’ means camera names, i.e.
SuperDVR & TD Series Cards User Manual 4 System Setup Figure4-4 Computer System Reboot Setup As the windows system may become unstable after a couple of days to continue operating. It may cause SuperDVR system unstable. The software support auto-reboot. Select and set the interval by day, which will guide the system to reboot automatically according to the setups. 5. Capture browse This item is the save path of capture files Users can fill in the specific save path for their capture pictures.
SuperDVR & TD Series Cards User Manual 4 System Setup 3. Hue Set image hue. 4. Saturation Set image Saturation 5. Default Load defaults, i.e. set the first four items value. The range of value is from 0—255. 4.3 Motion Detection Configuration Click and enter Motion Detection Configuration page, Figure4-6 Motion Detection Configuration Definition of the setup items: 1. Sensitivity Users can set motion detection sensitivity here. 2. Speed Motion detection sensitivity 3. Block Number Set grid’s number.
SuperDVR & TD Series Cards User Manual 4 System Setup 4.3.1 Set Motion Detection Area In case users want to customize the detection areas for a certain channel, first select the camera, then select ‘Clear’ and drag the cursor in the box in the left side. Now, users can see a green box appears which shows the motion detection area. Users can select maximum 16 customized areas for each channel. 4.3.2 Set Motion Detection Area By click ‘Clear’, users can clear all the selected areas. 4.
SuperDVR & TD Series Cards User Manual 4 System Setup Figure4-8 Edit Schedule 4.5 Motion Detection Alarm Configuration 4.5.1 Alarm Triggering Conditions Configuration The system can receive alarm from both local place and network. Local Alarm Record Triggering Configuration Figure4-9 Local Alarm Triggering Configuration Relative Explanations: 1. Buzzer Users can select whether to open the computer buzzer if the alarms have been triggered and also select how long the buzzer rings 2.
SuperDVR & TD Series Cards User Manual 4 System Setup 4.5.2 Alarm Record Figure4-10 Alarm Trigger Method Configuration Every sensor can trigger multiple channels to record. For example, if users select CAM1, CAM4 and CAM5 for Sensor2, then once the sensor is activated, CAM1, CAM4 and CAM5 will begin to record. Users can also select the voltage, high and low, for alarm signals. 4.5.
SuperDVR & TD Series Cards User Manual 4 System Setup 1. Video Loss Users can select alarm output for this option. For example, users select alarm_out1 and alarm_out3 for video loss. Then video loss of any channel will trigger alarm_out1, alarm_out3 to show red light in the Alarm output status panel (refer to Figure3-6 for reference). 2. Disk Alarm When HDD available space is less than the set value (see Figure4-9), it will trigger alarm. 3.
SuperDVR & TD Series Cards User Manual 4 System Setup Figure4-13 Auto Mail Setup To test the settings, click ‘Send Mail Test’. If all settings are okay, message ‘Message Sent Successfully’ will pop up. If some settings are wrong, there will pop up corresponding warning message. Enable ‘Attachment’, then the present image when an alarm triggered will be sent to appointed mailbox, referred Figure4-14. Figure4-14 Attachment Setup NOTICE For every alarm event, only one picture will be sent. 4.
SuperDVR & TD Series Cards User Manual 4 System Setup Figure4-15 E-Map Edit Draw the icon of camera to the corresponding position in the map, maximum 32 cameras can be set simultaneously, Click ‘change icon’ of camera by right key to change icon and click ‘Delete’ to cancel camera. After editing, click right key in the map and select ‘Save Map’ to save the current map.
SuperDVR & TD Series Cards User Manual 4 System Setup When a channel alarm, the camera icon will flash yellow alarm signal. Select ‘Auto Show’, in case of accident alarming, an alarming screen will pop out automatically and you can know about the alarming position rapidly. Click the camera head by right key to show the screen on the spot. NOTICE 1. The map tree currently supports three levels and it is invalid for addition exceeding three levels. 2.
SuperDVR & TD Series Cards User Manual 4 System Setup Figure4-18 P.T.Z Protocol Setup 1. Port Users can set serial port number. 2. Protocol Communication protocol of P.T.Z device 3. Address Communication address of P.T.Z device 4.7.2 Serial Ports Setup Users should firstly enable the P.T.Z control function of a certain camera and select a port number in P.T.Z Protocol Setup (refer to Figure4-18), and then set corresponding parameters in the area below: Figure4-19 P.T.Z Serial Port Setup 1.
SuperDVR & TD Series Cards User Manual 4 System Setup 4.8 Users Configuration Click and access the following area: Figure4-20 User configuration After installing the SuperDVR system, it will automatically create an administrator user of which user name is SYSTEM with no password. Users can use this username to log in the system and ‘Add’, ‘Edit’ or ‘Delete’ users’ parameters. 4.8.
SuperDVR & TD Series Cards User Manual 4 System Setup • Normal User: Normal user’s right is also endowed by the administrator. They have the same right list as power user. However, whether they can possess some right should be decided by the administrator. Only if the administrator ticks off some right, they will have the right. For example, if ticking off Basic Configuration, the normal user can conduct this right.
SuperDVR & TD Series Cards User Manual 5 P.T.Z Control 5 P.T.Z Control Click in the SuperDVR main display interface (refer to Figure3-1) and access to the following area: Figure5-1 P.T.Z Control Interface Users can control P.T.Z devices by the function buttons on the right side, see as below: Figure5-2 P.T.Z Control Function Buttons Panel In the upper circle, there are five function buttons, i.e. upward button, downward button, leftward button, rightward button, and stop button.
SuperDVR & TD Series Cards User Manual 5 P.T.Z Control (+ and -). Click values. and to increase and decrease the corresponding When users need to utilize P.T.Z control, first enter P.T.Z Control Interface (refer to Figure5-1), and click the corresponding channel (users can see a red fringe around the channel), then users can begin to control the enabled P.T.Z control enabled camera. NOTICE After pressing left mouse button on any function button in P.T.
SuperDVR & TD Series Cards User Manual 5 P.T.Z Control to set Preset point and change Preset point name. Every Click Group includes multiple Preset points. In case users select preset1, preset2 and preset3 for group1, preset1, preset2 and preset3 will be automatically accessed in sequence after users select group1 for auto scout. Figure5-5 Preset Click , a pop-pup window as following will appear: Dwell: users can set the dwell time of a preset here.
SuperDVR & TD Series Cards User Manual 6 Record Search & Playing Back 6 Record Search & Playing Back Click in the SuperDVR Main Display Interface (refer to Figure3-1) and access to the following areas: Figure6-1 Search and Playback Interface This interface is divided into 4 parts, i.e. record search area, record playing back area, record play area, and other functions area. Press 46 and return to the live surveillance status.
SuperDVR & TD Series Cards User Manual 6 Record Search & Playing Back 6.1 Record Search Figure6-2 Record Search Area A, B and C marks the areas of three search methods. • A: Search by date (range from Jan 1st, 1971 till now) • B: Search in backup file and original file • C: Search by record mode. This is useful when user wants to look through some important events. Users can select one or above of the three searching methods to search for needed record file. 6.
SuperDVR & TD Series Cards User Manual 6 Record Search & Playing Back • : Play / Pause • : Stop • : Play backwards. This button is valid when playing back by single channel • : Previous Section. This button is valid when playing back by single channel : Next Section. This button is valid when playing back by single • channel • : Previous Frame. This button is valid when playing back by single channel playing back pause mode : Next Frame.
SuperDVR & TD Series Cards User Manual • 6 Record Search & Playing Back Red: Sensor Alarm Record Events to play selected record files. The system offers playing back Click modes 1 Ch, 4CH, 9 CH, and 16CH. The following is multiple channels playing back control area: Figure6-6 Multiple Channels Playing Back Control The system default playing back mode is one channel. That is Camera1.
SuperDVR & TD Series Cards User Manual 6 Record Search & Playing Back Figure6-9 Channel Configuration Dialog for 9-channel Playing Back Mode Users can select any 9 channels from all the available channels for playing back. Users can also use the quick select methods by the system.
SuperDVR & TD Series Cards User Manual 6 Record Search & Playing Back Users can select corresponding cameras and copy the record files to another path in this area. This is the file backup function of the system. The interface is divided into four areas: • A: Camera Selection Area • B: Time and Date Selection Area • C: Operation Area • D: Information Area In A area, users can select one or more cameras.
SuperDVR & TD Series Cards User Manual 6 Record Search & Playing Back rectification for the present channel, including brightness, contrast, saturation and hue, and press ‘Default’ to recover to the original settings. Figure6-13 Color Control Panel When in the single channel playing back pause mode, click following window will appear as below: and the Figure6-14 Capture Multiple Images in Sequence Select path and click ‘Save’ to save the picture.
SuperDVR & TD Series Cards User Manual 6 Record Search & Playing Back Figure6-16 Print Preview Select and then click or to move the picture upward, downward, leftward and rightward. Select and then click and to zoom in and out the image. Press return to the original settings. Press ‘Print’ in the print preview window, users can print the image directly. 6.3.4 Image Zoom in/out When in single channel playing back state, the zoom control icons will appear.
SuperDVR & TD Series Cards User Manual 6 Record Search & Playing Back Figure6-18 Example: zoomed out Figure6-19 Example: zoomed in 54
SuperDVR & TD Series Cards User Manual 7 IE Client 7 IE Client Remote Live Surveillance Surveillance system supports Remote Surveillance through LAN, Internet, and Intranet. Simply enable web cam function of the system on a computer which is connected to Internet, and the computer system will become an Internet web cam server.
SuperDVR & TD Series Cards User Manual 7 IE Client 7.2 Accessing IE client If users want to remote view pictures, the IE client should be connected to LAN or Internet. And then enable network server in the unit. Please refer to Fig7.1 IE client Server Configuration. This unit supports IE browser, not any client software installed. And it supports Win XP and vista. Input the IE client server IP address in Internet Explorer and selected install ActiveX control, then the following figure appears: Fig 7.
SuperDVR & TD Series Cards User Manual 7 IE Client Fig 7.4 WebCam Main interface Corresponding Explanations: Icon Description means the dome rotate up. means the dome means the dome rotate left. means rotate down. the dome rotate right. means the dome stop rotating. 'Focus' button. Click have long focus. Click button near 'Focus' button to button near 'Focus' button button near 'Zoom' button to 'Zoom' button. Click zoom in the locale picture of this camera.
SuperDVR & TD Series Cards User Manual 7 IE Client Single channel with full screen display Four channel with four pictures display Contrast adjustment Brightness adjustment Hue adjustment Saturation adjustment Log in/ Log out Record playback System Configuration Enable the Lan that is Master stream, has higher frame rate and needs higher network bandwidth; Internet that is sub stream, has low frame rate and requires low net work bandwidth. Users can select the stream according to their bandwidth.
SuperDVR & TD Series Cards User Manual 7 IE Client Fig 7.5 Remote play back Explain of the button functions: : Play/ Pause : Stop : Adjust the speed of playing back. Users can select suitable play speed in needed. : Playing back backup. Back up record data of server-end. Users can click Backup, enter into the below interface: Fig 7.6 Remote backup STEP1： Select the date, channel, then click Search button. It will list all files recorded in the day.
SuperDVR & TD Series Cards User Manual 7 IE Client STEP2： Click Browse button, set the saving path. STEP3： Select files in the search area. Users can hold shift button of keyboard and select multi files with mouse simultaneously. STEP4： Click Backup button to do remote backup. Notice: the backup files are AVI format. Users can play with the third player directly.
SuperDVR & TD Series Cards User Manual 7 IE Client Users can select any four channels from all the available channels for playing back. The following area shows the record files of different channels: Fig 7.9 Data Preview Data preview shows the record data for different channels in corresponding time, the left side shows the available channels.
SuperDVR & TD Series Cards User Manual 7 IE Client Fig 7.10 Basic Configuration Notice: When multi-client accessed the system configuration interface simultaneous, the user who enters into that interface priority and then others will lack of accessing rights. 7.4.1 Basic Configuration Fig 7.11 Basic setup 1. Caption There are four options: None, ID, Name and ID/Name for select from. z ‘None’means no title z ‘ID’means camera numbers, i.e.1,2,3 and so on z ‘Name’means camera names,i.e.
SuperDVR & TD Series Cards User Manual 7 IE Client Fig 7.12 Computer System Reboot Setup As the windows system may become unstable after a couple of days to continue operating. It may cause SuperDVR system unstable. The software supports auto-reboot. Select and set the interval by day, which will guide the system to reboot automatically according to the setups. 3. Alarm setup The Alarm setup configuration is show as below: Fig 7.13 Alarm triggering configuration Relative Explanations: 1.
SuperDVR & TD Series Cards User Manual 7 IE Client 7.4.2 Camera setup Click and the camera setup configuration will appear as below: Fig 7.14 Camera setup configuration 1. Title Channel name. Users can set the channel name from Cam1, Cam2, Cam3 and Cam4. 2. Camera security Users are divided into two standards: normal user and super admin. By selecting this option, only administrator can see corresponding channels. 3.
SuperDVR & TD Series Cards User Manual 7 IE Client Fig 7.15 Schedule configuration There have three kinds of record modes: schedule record, motion detection and Sensor alarm record. We provide users to set schedules from Sunday to Monday separately for all of the three record modes. Sensor alarm recording mode has the highest priority among others. When users need to edit schedule for a channel, select the camera name in the left Camera group firstly.
SuperDVR & TD Series Cards User Manual 7 IE Client , users could copy the setting of this channel to any other If click selected channel. 7.4.5 Record configuration Click icon and enter into record configuration interface as below: Fig 7.17 Record configuration 1. Record setup Fig 7.
SuperDVR & TD Series Cards User Manual 7 IE Client c. Schedule record Schedule record option d. Motion record By selecting this option, users can set relative channels’ record mode as motion detection. 2. Storage disk Fig 7.19 Storage disk Users can store record file by selecting storage disk. Tick off ‘Recycle’check box, users can set whether to continue recording to cover the earliest video file when the disc storing video files is full.
SuperDVR & TD Series Cards User Manual 7 IE Client Motion detection sensitivity 3. Block number Set grid’s number 4. Select all Select all the areas of the channel as detection area 5. Clear all Clear all the detection areas and then users can select customized detection areas by cursor. , users could copy the setting of this channel to any other If click selected channel. 7.4.7 EMAIL Configuration icon and access to Email configuration interface: Click Fig 7.21 Email configuration 1.
SuperDVR & TD Series Cards User Manual 7 IE Client Password: Sender’s Password Users can select ‘My server requires a secure connections’ or ‘My outgoing server （SMTP）requires authentication’check box according to server mail service of mail service supplier. 2. Mail setup Fig 7.
SuperDVR & TD Series Cards User Manual 7 IE Client Fig 7.25 P.T.Z Configuration 1. Protocol setup Fig 7.26 P.T.Z Protocol setup A. Protocol Communication protocol of P.T.Z device B. Port Users can set serial port number C. Address Communication address of P.T.Z device 2. Serial port setup Users should firstly enable the P.T.Z control function of certain camera and select a port number in P.T.
SuperDVR & TD Series Cards User Manual 7 IE Client Fig 7.27 P.T.Z Serial port setup A. Port Users can set port number B.Baud rate Set P.T.Z device Baud rate, default value is 9600 C.Data bits Default value is 8 D.Parity Odd and even parity bit, default Null E.Stop bits Default value is 1 Notice: Users should look into the P.T.Z device and get Baud rate, Protocol and Address firstly, and then set other values accordingly.
SuperDVR & TD Series Cards User Manual 7 IE Client Parameter Brand O2 NOKIA NOKIA TYPE O2 Xda II O2 Xda Atom(3G) O2 Xda Mini Nokia N70 Nokia N73 Nokia N80 Nokia N-Gage Nokia 3230 Nokia 3250 Nokia 6260 Nokia 6630 Nokia 6680 Nokia 7610 Nokia N-95 SYSTEM Windows Mobile 2003 Windows Mobile 5.0 Windows Mobile 2003 S60 OS8.1a S60 OS9.1 S60 OS9.1 S60 OS6.1 S60 OS7.0s S60 OS9.1 S60 OS7.0s S60 OS8.0s S60 OS8.0s S60 OS7.0s S60 OS9.2 Table 7-1 Mobile Phone of Supporting Mobile Surveillance 7.5.
SuperDVR & TD Series Cards User Manual 7 IE Client Fig 7.30 Connect to Server Step3: Click ‘Scam_S3_080919.sis’ to start downloading and a confirmation information window will pop up after downloading is finished. Fig 7.31 Confirmation Information Window Step4: Click ‘OK’, the system reminds of whether to install the ‘Webcam’. Fig 7.32 Installing Configuration Information Step5: Click ‘Yes’ to start installing. A Scam shortcut icon appears on the system menu after the installation has been done.
SuperDVR & TD Series Cards User Manual 7 IE Client Step6: Run ‘Scam’ by selecting the icon: Fig 7.34 Main Layout of Scam Step7: Enter the main menu by selecting ‘Live View’.A Setting window will pop up and select ‘Login Setting ’to login.
SuperDVR & TD Series Cards User Manual 7 IE Client Frequently Asked Questions Fig 7.37 Alarm Setting Sound Alarm: Sound alarm Note: The software is running in the background, what kind of methods (sound alarm or vibration tips) that users want to be informed when an unusual occurs in remote site.
SuperDVR & TD Series Cards User Manual Appendix1 Frequently Asked Questions Appendix1 Frequently Asked Questions Appendix 2.1 Installation Appendix 2.1.1 Cannot Install the SuperDVR Driver Possible causes: • TD series capture card has not been installed. Before installing driver, users should install capture card hardware in the PCI slot in the computer case. • TD series capture card has not been installed correctly. Please unplug the card and install it again or change to another PCI slot.
SuperDVR & TD Series Cards User Manual • • Appendix1 Frequently Asked Questions TD series card error. Change for a valid one. Install SuperDVR. Appendix 2.2 How to Use SuperDVR Appendix 2.2.1 Meanings of the indicator lights • Grey- Normal state • Red - Sensor alarm • Yellow - Motion detection alarm • Blue - Video loss • Bottle Green - Manual record state • Reseda - Schedule record state NOTICE Users can refer to Figure3-6 to learn more. Appendix 2.2.
Appendix1 Frequently Asked Questions SuperDVR & TD Series Cards User Manual TIPS Users do not need enable auto reboot function, but it’s suggested to input the Windows user name and password in the relative area, therefore when meeting abnormal system exit, users don’t need to be troubled to input Windows and SuperDVR user names and passwords. Appendix 2.2.
SuperDVR & TD Series Cards User Manual Appendix1 Frequently Asked Questions Appendix 2.3.3 Why can’t the server be configured at the client-side? The possible causes: • It cannot be configured at the client-side, when the server is being configured at the server-end. • Only the last configuration is valid if server different configuration are deployed simultaneously. Appendix 2.3.4 Why I can’t see the images? The possible causes: • The VGA card is too outdated. • Have not installed newer DirectDraw.
Appendix1 Frequently Asked Questions SuperDVR & TD Series Cards User Manual Appendix 2.4.2 Why I can’t find the recorded files? HDD space is not enough. Appendix 2.4.3 Why the screens display is unstable with dithering and water-wave images? Possible causes: • Camera electrical power is not enough. • There is external electromagnetic disturbance, or electrostatic disturbance of camera BNC connector (It is suggested to connect ground wire to the connector). • User has not installed necessary VGA driver.
SuperDVR & TD Series Cards User Manual Appendix1 Frequently Asked Questions Appendix 2.4.8 Precautions on changing system time • The superDVR system provides the retrieving mechanism for video files, which must take the system time as a retrieving reference. To change the computer time after installation will create a high risk of wrong time reference. • Before superDVR is used, it must be confirmed whether the current computer time is correct. • Deactivate computer auto time updating function of system.
SuperDVR & TD Series Cards User Manual Appendix2 Quick Start for Using Appendix2 Quick Start for Using Appendix 3.1 Requirements Before installing the PCI card, check PC requirements: • • • • • • Pentium 2.8 GHZ 512 MB RAM Windows 2000 (SP4 min) or Win XP (SP2 min) NVIDIA Video Card with 64 MB min or similar DirectX 9.0 minimum 80 GB HDD NOTICE TD3104 and TD3316 support Windows 2000(SP4 min) or Windows XP(SP2 min). Appendix 3.
SuperDVR & TD Series Cards User Manual Appendix2 Quick Start for Using Appendix 3.3 Troubleshooting Appendix3.3.1 When opening the SuperDVR program, it says ‘ Can’t find card ’. Reboot one more time. If still same problem, click ‘Start - Program SuperDVR - Install’ and then uninstall the program. Reboot the computer. After reboot, go back to ‘Start - Program - SuperDVR - Install’. Now click on ‘Install’ to reinstall driver. Then Reboot. If for some reason still ‘Can’t find card ’, uninstall driver again.
Appendix2 Quick Start for Using STEP5： icon. STEP6： SuperDVR & TD Series Cards User Manual download Remote Playback as well. On Desktop now you should see ‘WebCam’ and ‘Remote Playback’ Open up webcam, click ‘Key’ symbol icon. Username: system (Password blank unless you setup a password within the main computer). Server: this the IP address of the Main Computer. Data port: 1159 and Command port: 1160. Click ‘OK’. Now you should be able to view the live video from main STEP7： computer.
SuperDVR & TD Series Cards User Manual Appendix3 Function Tree Appendix3 Function Tree Appendix 4.
SuperDVR & TD Series Cards User Manual Appendix3 Function Tree Appendix 4.
SuperDVR & TD Series Cards User Manual Appendix3 Function Tree Appendix 4.
SuperDVR & TD Series Cards User Manual Appendix3 Function Tree Appendix 4.
