Specifications
1061
TORQUE
WRENCH
SETTINGS
.
TRANSFER
BOX
LT230R
.
4
-
cylinder Petrol and Diesel engine
Pinch bolt, operating arm ......................................
Gate plate to grommet plate
...................................
Speedometer cable retainer
....................................
Locating plate to gear change housing .......................
Cross shaft housing to front output housing
................
Gear change housing
............................................
Pivot shaft
..........................................................
Connecting rod ...................................................
Retaining plate intermediate shaft
...........................
Front output housing cover
....................................
Gear change housing
............................................
Bracket
to
extension housing ..................................
End cover ..........................................................
Speedometer housinghear output
............................
Bottom cover to transfer
case
.................................
Front output housing to transfer case
........................
Finger housing to front output housing
......................
Mainshaft bearing housing
.....................................
Brake drum ...............................
Gearbox to transfer box
........................................
Bearing housing to transfer gearbox
.........................
Speedometer housing
to
transfer gearbox ..................
Selector fork to cross shaft
.....................................
Yoke to selector shaft high/low
...............................
Selector fork high/low to shaft
.................................
Transmission brake ..............................................
Gearbox to transfer case
........................................
Gearbox to transfer case ........................................
Oil drain plug
......................................................
Differential case ..................................................
Differential case rear and shaft main drive
214
-
wheel drive
.................................................
Link arm and cross shaft lever to ball joint
.................
Transfer breather
.................................................
Operating arm high/low
.........................................
Output flange
.....................................................
Oil filler/level plug
...............................................
Nm
7-
10
7-
10
7- 10
7-
10
See
note
5
-
7
22
.
28
22
.
28
22
.
28
22
.
28
22
.
28
22
.
28
22
.
28
22
.
28
22
.
28
22
.
28
22
.
28
22
.
28
22
.
28
40
.
50
40
.
50
40
.
50
22
.
28
22
.
28
22
.
28
22
.
28
65
.
80
40
.
50
See note
25
.
35
55
.
64
146
.
179
66
.
80
8- 12
25
.
35
7-
11
Ibf
ft
5
-
7
5
-
7
5
-
7
5
-
7
4
-
5
16
.
21
16
.
21
16
1
21
16
.
21
16
.
21
16
.
21
16
.
21
16
.
21
16
.
21
16
.
21
16
.
21
16
.
21
16
.
21
29
.
37
29
.
37
29
.
37
16
.
21
16
.
21
16
.
21
16
.
21
48
.
59
29
.
37
19
.
26
40
.
47
108
.
132
50
.
60
6
-
9
19
.
26
5
-
8
NOTE:-
Studs to be assembled into casings with sufficient torque
to
wind them fully home. but this torque must not
exceed the maximum figure quoted for the associated nut on final assembly
.
TRANSFER GEARBOX LT230T
.
4 cylinder Petrol and Diesel engine and
VS
Fixings securing mounting brackets to gearbox
...........
Pinch bolt operating arm
.......................................
Speedometer cable retainer
....................................
speedometer housing
...........................................
Front output housing to transfer
..............................
Gate plate to grommet plate
...................................
Bearing housing to transfer case
..............................
Locating plate to gear change
.................................
Bottom cover
to
transfer
........................................
Front output housing to transfer ..............................
80
.
100
7-
10
7- 10
7-
10
7-
10
See note
5
-
7
22
.
28
22
.
28
22
.
28
59
.
73
5
-
7
5
-
7
5
-
7
5
-
7
4
-
5
16
.
21
16
.
21
16
.
21
4