Warranty

ManualsBrandsDefiant ManualsDoor HardwareCastle Aged Bronze Touchscreen Electronic Deadbolt with Naples Passage Lever Combo Pack

WARRANTY

13/16" (20 mm) Screw Qty. 2

CAUTION:

Please use four alkaline batteries for the best performance.

CARE and MAINTENANCE:

The following instructions should be followed to properly protect and maintain your lockset:

Read the precautions and instructions in this manual before installing and using this lock. Save this manual for future reference.

A. Remove locks, or do not install locks, prior to painting your door.

B. Periodically clean with mild soap and a soft cloth only.

C. Do not use any abrasives or chemical products containing alcohol, benzene, acids, and avoid using sharp or abrasive objects to clean this lockset.

D. Do not allow any water or liquids into the lockset during installation.

A. Do not attempt to disassemble any internal components of the lockset. Doing so will void the limited warranty.

B. Do not drop or hit the lockset. Too much shock may result in permanent damage.

C. Do not use pins or sharp objects to press the keypad.

D. Always create a backup of information you wish to keep (Master Code, User Codes,etc.) Please use the last page of this booklet as a reference.

E. Promptly change the Master Code before operating this lockset

Safety Information

WARNING:

If the door needs to be drilled, please be familiar with how to use a drill safely and understand all of the door preparation steps before proceeding.

Pre-installation – Tools Required / Hardware Included

Dust Box

Key

Drive-in Collar (Optional)L

Exterior Gasket

Interior Assembly

Battery Cover

Latch

Strike Plate

Exterior Assembly

Power Cable

Torque blade

Mounting Plate

Part

Description

Part

Description

The cable must be arranged as shown in the diagram.

Insert screws

and tighten.

Connect the cable

rmly into

connector port .

Remove the Battery Cover

The bulged part of the mounting plate

must face towards the door.

Install the lock assemblies

Slide the cable through the

notch in mounting plate.

The latch bolt should be

in retracted position.

Thread the cable through

the hole and under the latch.

For installation into 1-1/2”(38mm) bore hole,

simply pry the adapter collar off with a

screwdriver.

Install batteries Install battery cover

Enter default Master Code (123456)

and the lock will set up bolt

direction to complete installation.

LIMITED LIFETIME MECHANICAL AND 1 YEAR ELECTRONIC WARRANTY

The retailer of this product, hereby warrants, subject to the conditions set forth below, that it will either repair or replace, at its option, this product if it

proves to be defective by reason of improper workmanship or materials within the original purchaser's limited time. In order to obtain repairs or

replacement under this limited warranty you must bring this product to the retailer's store in which you bought it.

Original purchaser: This limited warranty is limited to the original purchaser at retail of this product from retailer.

Except to the extent prohibited by applicable law, no other warranties, whether express or implied, including the warranties of merchantability and tness

for a particular purpose, shall apply to this product. Under no circumstances shall retailer be liable for consequential or incidental damages in connection

with this product. To the extent retailer is prohibited by applicable law from excluding implied warranties, the duration of such implied warranties which

are not excludable shall be the original purchaser's lifetime. Some states do not allow the limitation on how long an implied warranty lasts, so the above

limitation on the duration of implied warranties which are not excludable, if any, may not apply to you. Some states do not allow the exclusion or limitation

of incidental or consequential damages, so the above limitation or exclusion of incidental or consequential damages may not apply to you.

Retailer neither assumes not authorizes any representative or other person to assume for it any obligation or liability other than such as is expressly set

forth herein. This limited warranty gives you specic legal rights, and you may also have other rights which vary from state to state.

FOR

M32-KPDA612-XQ Rev. 18/04-00

Hardware Used

Questions, problems, missing parts? Before returning to the store,

call Deant Customer Service

TOLL FREE HELP LINE 1-877-ONE-LOCK

HOMEDEPOT.COM

08:30 a.m.-05:30 p.m., EST, Monday - Friday

https://goo.gl/mcceCM

SCAN FOR

INSTALLATION

CAUTION :

1.Please use four alkaline batteries for better performance. Be sure to insert them correctly by matching the + and – polarity

markings. Do not mix old batteries and new batteries or standard (carbon-zinc) with alkaline batteries.

2.Install and test lock with door OPENED to avoid being locked out.

Optional Optional Optional Optional Optional Optional

PACKAGE CONTENTS LIST

HARDWARE CONTENTS (Actual Size)

1-13/16" (46 mm) Mounting Bolt Qty. 2

3/4 in. (19 mm) Wood screws Qty. 8

1-23/64 in. (34mm) mounting screws Qty. 2

Actual Size

Press





LatchO

Strike PlateP

Inside Lever Assembly

Outside Lever Assembly

Drive-in Collar (Optional)

Adapter collar

Note : The metal connector

side should face outward.

A. Using the template, mark the door and drill the holes, and chisel out a mortise.

1-1/2” (38mm)

2-1/8"(54 mm)

DOOR DRILLING FOR NEW INSTALLATION

NOTE: If your door already has holes, skip to step

B. PREPARE DOOR JAMB

Choose Faceplate

Set the Latch Backset

Installation

180º

”

(

)

2-3/4’’

(70 mm)

2-3/8’’

(60 mm)

”

(

)

Door jamb hole dimension

a. 1-3/16" (30 mm)

b. 1-9/64" (29 mm)

c. 7/8" (22 mm)

d. 5/32" (4 mm)

e. 2-1/4" (57 mm)

f. 1" (25 mm)

Door jamb hole dimension

a. 1-/2" (13 mm)

b. 1-1/16" (27 mm)

c. 1/8" (19 mm)

d. 1/16" (1.5 mm)

e. 2-5/16" (58 mm)

f. 1-7/16" (36 mm)

Outline

Chisel 1/8” (3mm) deep

1”

25 mm

B. INSTALL STRIKE PLATE IN DOOR JAMB

Tap Latch Flush

Wood Block (not included)

Backset

Hardware Used

Actual Size

Hardware Used

NOTE: If required, bend the

adjustable tang on the strike to

eliminate a loose fit between the

door and the door stop.

C. INSTALL LEVER

D. INSTALL ELECTRONIC DEADBOLT

INSIDE OUTSIDE

A. INSTALL LATCH

Hardware Used

Actual Size

SWITCH HANDLES

(IF DESIRED)

BEFORE PROCEEDING

Check Dimensions

1-3/8” - 1-3/4”

(35mm - 45mm)

2-3/8” (60mm)

2-3/4” (70mm)

1-1/2” (38mm)

2-1/8” (54mm)

1” (25mm)

2-1/8” (54mm)

NOTE: Levers installed in reverse

will not affect the product’s

performance.

1-1/2” (38mm)

2-1/8"(54 mm)

2-1/8"

(54 mm)

Centerline

(25 mm)

Backset

1”

1/8”

25 mm

3 mm

Chisel 1/8” (3mm) deep

a. Outline

Insert pick-up pin into catch hole and pull lever off. Repeat the same on the inside to

remove inside lever.

Swap levers. Align the hole on the lever with the catch hole, and insert the

lever until secure.

Pull

2-3/8” (60 mm)

2-3/4” (70 mm)

Summary of content (2 pages)

PAGE 1
M32-KPDA612-XQ Rev. 18/04-00 3 DOOR DRILLING FOR NEW INSTALLATION NOTE: If your door already has holes, skip to step 4 A. Using the template, mark the door and drill the holes, and chisel out a mortise. FOR Centerline 1-1/2” (38mm) OR 2-1/8"(54 mm) 1" (25 mm) 1-1/2” (38mm) OR 2-1/8"(54 mm) 1” 25 mm 1/8” 3 mm a. Outline O b. Chisel 1/8” (3mm) deep Questions, problems, missing parts? Before returning to the store, call Defiant Customer Service Backset TOLL FREE HELP LINE 1-877-ONE-LOCK HOMEDEPOT.
PAGE 2
SCAN FOR PROGRAMMING PROGRAMMING https://goo.gl/mcceCM 1 HOW TO LOCK / UNLOCK THE LOCKSET OVERVIEW OF FUNCTIONS / LOCK BUTTON ENTER 1. Red light: Represents an incorrect entry or the unit is in programming mode. 2. Yellow light: Flashes when the batteries are low in power. 3. Green light: Represents a correct entry. 4. Press to activate or lock the lockset. Press “ 1 2 3 4 5 6 7 8 9 0 To lock ” to lock. Use a mechanical key to lock. OR → 1 2 3 4 5 6 7 8 9 0 1.