TMMQ/GPTD-PS/A00 Guangdong TIANQIU Electronics Technology Co. Ltd. TECHNICAL SPECIFICATION FOR MANGANESE DIOXIDE LITHIUM BATTERY TYPE:CR2025 Document No. TMMQ/GPTD-BPS409 Effective date Edition A00 Pages Compiled Revision Auditing Approved 2019-11-2 Total 7 pages Guangdong TIANQIU Electronics Technology Co. Ltd. ADD: 9/F TianQiu Business Building No.16-30, He Yi Rd., San Yuan Li Ave., GuangZhou China (Tel):020-36322277 (Fax):020-36323339 (P.C):510410 (Website):http://www.tmmq.
TMMQ/GPTD-PS/A00 Guangdong TIANQIU Electronics Technology Co. Ltd. 1. Scope This specification is applicable to the Manganese Dioxide Lithium Battery CR2025 supplied by Guangdong TIANQIU Electronics Technology Co. Ltd. 2. Designations 2.1Defining At the temperature of 20±2℃, loading at 15kΩ continuous discharge, till the voltage down to 2.0V 3. Designations and Dimensions 3.1 Designations: Manganese Dioxide Lithium Battery CR2025 3.2 Dimensions specification standard(mm) MAX MIN 2.5 2.
TMMQ/GPTD-PS/A00 Guangdong TIANQIU Electronics Technology Co. Ltd. 5. Technical requirements 5.1 Test conditions Unless otherwise specified, the test conditions shall be, as a general rule, at the temperature of 20±2℃ and the relative humidity of 60±15%. 5.2 NO. 5.2.1 5.2.2 Electrical characteristics Item Test condition Sampling plan:MIL-STD-105E, General Inspection Lever Ⅱ, Single Sampling, storage AQL=0.
TMMQ/GPTD-PS/A00 Guangdong TIANQIU Electronics Technology Co. Ltd. 6. Packing and marking 6.1Marking Design Any specific design and packing requirements will be accommodated as required. But as a general, the following markings will be printed, stamped or impressed on the body of the battery: We reserve all rights for the change of product specification and any information without any prior notice.
TMMQ/GPTD-PS/A00 Guangdong TIANQIU Electronics Technology Co. Ltd. 6.2 date code Manufacturing marks: the year and month of product shall be marked on the negative (-) terminal side.
TMMQ/GPTD-PS/A00 Guangdong TIANQIU Electronics Technology Co. Ltd. 6.3 Packing Picture We reserve all rights for the change of product specification and any information without any prior notice.
TMMQ/GPTD-PS/A00 Guangdong TIANQIU Electronics Technology Co. Ltd. 7.Caution for Use 1) Since the battery is not designed to be charged, there are risks of electrolyte leakage or causing damage to the device if the battery is charged. The battery shall be installed with its “+” and “-” polarity in correct position, otherwise may cause the battery to be charged or over-discharged. 3) Short-circuiting, heating, disposing of in fire and disassembling the battery are prohibited.
SDS- Primary Battery Issue date: 2019.04.22 Safety Data Sheet The batteries are exempt articles and are not subject to the OSHA Hazard Communication Standard Requirement. This sheet is only provided as technical information and is referred normal use of the product in question. Pairdeer makes no warranty expressed or implied.
SDS- Primary Battery Issue date: 2019.04.22 Section 3-Composition/Information on Ingredients Ingredient CAS# Approximate Content (wt%) Manganese Dioxide (MnO2) 1313-13-9 Zinc (Zn) 7440-66-6 Water (H2O) 7732-18-5 Zinc Chloride (ZnCl2) 7646-85-7 Ammonium Chloride(NH4Cl) 12125-02-9 Acetylene Black 1333-86-4 Steel 7439-89-6 Carbon 7440-44-0 PE 9002-88-4 27.1 28.5 16.9 7.2 1.3 4.9 3 7.6 3.5 Section 4-First Aid Measures None unless internal materials exposure.
SDS- Primary Battery Issue date: 2019.04.22 Section 6-Accidental Release Measures Steps to be taken in case material is released or spilled. Batteries that are leakage should be handled with rubber gloves. Avoid direct contact with electrolyte. Wear protective clothing and a positive pressure Self-Contained Breathing Apparatus (SCBA). Section 7-Handling and Storage 1) Handling Never swallow. Never charge. Never heat. Never expose to open flame. Never disassemble.
SDS- Primary Battery Issue date: 2019.04.22 Section 13-Disposal condition The battery may be regulated by national or local regulation. Please follow the instructions of proper regulation. As electric capacity is left in a discarded battery and it comes into contact with other metals, it could lead to distortion, leakage, overheating, or explosion, so make sure to cover the (+)and (-) terminals with friction tape or some other insulator before disposal.
SDS- Primary Battery Issue date: 2019.04.