Item #1002578077 Model #DFI-5886-WH USE AND CARE GUIDE MOTION SECURITY LIGHT Questions, problems, missing parts? Before returning to the store, call Defiant Customer Service 8 a.m.-7 p.m., EST, Monday-Friday, 9 a.m. - 6 p.m., EST, Saturday 1-866-308-3976 HOMEDEPOT.COM THANK YOU We appreciate the trust and confidence you have placed in Defiant through the purchase of this motion security light. We strive to continually create quality products designed to enhance your home.
Table of Contents Tools Required .......................................3 Hardware Included.................................4 Package Contents ..................................4 Installation ................................................5 Operation...................................................7 Care and Cleaning ..................................10 Troubleshooting ......................................10 Table of Contents ......................................2 Safety Information ..................
Pre-Installation PLANNING INSTALLATION Before installing the light fixture, ensure that all parts are present. Compare parts with the Hardware Included and Package Contents sections. If any part is missing or damaged, do not attempt to assemble, install, or operate this light fixture. Estimated installation time: 30 minutes SPECIFICATIONS Range Up to 70 ft. (21.
Pre-Installation (continued) HARDWARE INCLUDED NOTE: Hardware shown to actual size.
Installation the mounting 1 Determining location NOTE: The light fixture should be mounted approximately 8 ft. (2.4 m) above the ground. If the light fixture is mounted higher than recommended, aiming the sensor down will reduce the coverage area. Ƒ Ƒ Ƒ Wall Mount Determine the mounting location – wall or eave mount. Position the lamp heads (A) in the general direction of the desired light coverage. If needed, rotate the motion sensor (C) so the controls face the ground after installation.
Installation (continued) the electrical 4 Installing the mounting plate 5 Making connections Ƒ Ƒ Ƒ Ƒ Ƒ Ƒ Route the junction box wires through the hole in the mounting plate (D). Place the mounting plate (D) against the junction box. Ƒ When mounting to a wall, the “UP” arrow must point upward. Ƒ When mounting to an eave, the “UP” arrow must point toward the building.
Installation (continued) around the light 7 Caulking fixture CAUTION: Failure to completely caulk around the light fixture’s mounting plate (D) could result in water seepage into the light fixture (B) and/or junction box. Ƒ D Caulk around the mounting plate (D) and mounting surface with silicone sealant (not included).
Operation (continued) the motion sensor 3 Setting the sensor for testing 4 Adjusting detection zone Ƒ NOTE: When the “ON-TIME” switch is set to the “TEST” position, the light fixture will operate during the day or night. The light will stay on for 8 seconds after all motion is stopped. Ƒ Ƒ Set the “ON-TIME” switch to the “TEST” position. Set the “DUALBRITE” switch to the “OFF” position. Slide the “SENS” switch to the “L” (low) position.
Operation (continued) the DUALBRITE 7 Adjusting switch the Adjustable Color 8 Adjusting Temperature dial NOTE: The “DUALBRITE” switch determines the amount of time the lights stay on at an accent level after sundown. Switching this setting to “OFF” will not affect the “ONTIME” setting. Ƒ NOTE: The Adjustable Color Temperature adjustment is only available when the light is in full-bright mode. When the light is in accent (DualBrite) mode, the LED color is pre-set to 3000K (Kelvin).
Care and Cleaning Ƒ To prolong the original appearance, clean the light fixture with clear water and a soft, damp cloth only. Ƒ Do not use paints, solvents, or other chemicals on this light fixture. They could cause a premature deterioration of the finish. This is not a defect in the finish and will not be covered by the warranty. Ƒ Do not spray the light fixture with a hose or power washer. Troubleshooting Problem Possible Cause Solution The light will not come on.
Troubleshooting (continued) Problem Possible Cause Solution The lights turn off too late in the Dusk-to-Dawn setting. The light fixture may be installed in a relatively dark location. Relocate the light fixture or use the 3 hour or 6 hour setting. The lights stay on continuously. Ƒ The motion sensor may be picking up a heat source, such as an air vent, dryer vent, or brightly painted, heat-reflective surface. Ƒ Decrease the “SENS” setting or reposition the motion sensor.
Questions, problems, missing parts? Before returning to the store, call Defiant Customer Service 8 a.m.-7 p.m., EST, Monday-Friday, 9 a.m. - 6 p.m., EST, Saturday 1-866-308-3976 HOMEDEPOT.COM Retain this manual for future use.
Articulo #1002578077 Modelo #DFI-5886-WH GUÍA PARA EL USO Y CUIDADO LUZ DE SEGURIDAD POR MOVIMIENTO ¿Tiene preguntas, problemas o piezas faltantes? Antes de devolverlo a la tienda, llame a Servicio al Cliente de Defiant de 08 a.m.-7 p.m., EST, Lunes - Viernes, 09 a.m.-6 p.m., EST, sábado. 1-866-308-3976 HOMEDEPOT.COM GRACIAS Agradecemos la fe y la confianza que usted ha depositado en Defiant al comprar esta luz de seguridad por movimiento.
Contenido Herramientas Requeridas ....................15 Ferretería Incluida................................16 Contenido del Paquete .........................16 Instalación ..............................................17 Operación ................................................19 Cuidado y limpieza .................................21 Análisis de averías .................................22 Contenido ................................................14 Información de seguridad ......................
Antes de la instalación PLANIFICACIÓN DE LA INSTALACIÓN Antes de instalar el aparato de luz, esté seguro que estén todas las piezas. Compare las piezas con la Ferretería incluida y las secciones de Contenidos del paquete. Si cualquier pieza falta o está dañada, no intente ensamblar, instalar ni operar este aparato de luz.
Antes de la instalación (continuación) FERRETERÍA INCLUIDA NOTA: La ferretería se muestra en su tamaño real AA BB CC DD FRONT EE FF GG Pieza Descripción Cantidad AA Tapón de caucho 1 BB Tornillo del soporte de montaje 2 CC Tornillo del soporte de montaje 2 DD Tornillo grande de montaje (pre-instalado) 1 EE Tornillo pequeño de montaje 1 FF Soporte de montaje (no está a escala) 1 GG Mini-destornillador 1 CONTENIDO DEL PAQUETE A B D C Pieza Descripción Cantidad A Cabezal de
Instalación del sitio de 1 Determinación montaje NOTA: Esta lámpara debe ser instalada aproximadamente a 8 pies (2,4 m) por encima del suelo. Si se la instala a una altura más alta de la recomendada, se reducirá la zona de cobertura si apunta el detector hacia abajo. Ƒ Ƒ Ƒ 2 Montaje en pared Determine el sitio de montaje – pared o alero. Coloque los cabezales de la lámpara (A) en la dirección general de la cobertura de luz deseada.
Instalación (continuación) de la placa de 4 Instalación montaje Ƒ Ƒ Ƒ Ƒ hacer las conexiones 5 Cómo eléctricas Ƒ Pase los cables de la caja de conexiones por el agujero que está en la placa de montaje (D). Coloque la placa de montaje (D) contra la caja de conexiones. Ƒ Cuando la instale sobre una pared, la flecha “UP” (Hacia Arriba) debe apuntar hacia arriba. Ƒ Cuando la instale sobre un alero, la flecha “UP” (Hacia Arriba) debe apuntar hacia el edificio.
Instalación (continuación) alrededor del aparato 7 Calafatee de luz PRECAUCIÓN: No calafatear por completo alrededor de la placa de montaje (D) de la lámpara puede resultar en la filtración del agua en la lámpara (B) y / o la caja de conexiones. Ƒ D Calafatee alrededor de la placa de montaje (D) y de la superficie de montaje con un sellador de silicona (no incluido). Operación de los cabezales de la hacia abajo de los 1 Ajuste 2 Giro lámpara controles del detector ADVERTENCIA: Riesgo de incendio.
Operación (continuación) del detector para de la zona de 3 Calibración 4 Regulación prueba detección del detector de movimiento NOTA: Cuando el interruptor de “DURACIÓN” (“ON-TIME”) se fija en la posición “PRUEBA” (“TEST”) el aparato de luz operará durante el día o la noche. La luz permanecerá encendida 8 segundos después que todo movimiento se ha detenido. Ƒ Ƒ Ƒ Fije el interruptor de “DURACIÓN” en la posición “PRUEBA (“TEST”). Fije el interruptor “DUALBRITE” en la posición “APAGADO” (“OFF”).
Operación (continuación) del interruptor 7 Regulación DUALBRITE del dial de temperatura 8 Ajuste de color ajustable NOTA: El interruptor DUALBRITE determina el lapso de tiempo que la luz permanece encendida con un nivel de luz reducido luego de la puesta del sol. Cambiando esta calibración a “OFF” (“DESCONECTADO”) no quedará afectada la calibración de la DURACIÓN. Ƒ NOTA: El ajuste de temperatura de color ajustable está disponible sólo cuando la luz está en modalidad de brillo completo.
Análisis de averías Problema Causa Probable Solución La luz no se enciende. Ƒ El interruptor de la luz está apagado. Ƒ Encienda el interruptor de la luz. Ƒ El fusible está quemado o el disyuntor está desconectado. Ƒ Cambie el fusible o conecte el disyuntor. Ƒ La lámpara no está correctamente sujetada a la placa de montaje, si se trata de una nueva instalación (las clavijas no están asentadas por completo en el bloque de terminales).
Análisis de averías (continuación) Problema Causa Probable Solución Las luces se apagan demasiado tarde en la calibración crepúsculo-al-amanecer. El aparato de luz puede estar instalado en un sitio relativamente oscuro. Vuelva a ubicar el aparato de luz o utilice la calibración 3 horas o 6 horas. Las luces permanecen encendidas constantemente.
¿Tiene preguntas, problemas o piezas faltantes? Antes de devolverlo a la tienda, llame a Servicio al Cliente de Defiant de 08 a.m.-7 p.m., EST, Lunes - Viernes, 09 a.m.-6 p.m., EST, sábado. 1-866-308-3976 HOMEDEPOT.COM Guarde este manual para uso futuro.