Installation Guide

ManualsBrandsDefiant ManualsDoor HardwareSingle Cylinder Square Electronic Deadbolt Matte Black with Biometric Fingerprint and Keypad



This procedure will delete all User Codes associated with the lock.



Keep the door open and unlock.



Press and hold the Reset button. At the same time take out one battery and then place it back.



Keep holding the Reset button for at least 3 seconds, until you hear the sound of beep.

Quick Set Up

Programming Instructions



Master Code (4 to 10 digits): The default Master Code is 12345678. It is required that you change it

to a code of your own before programming.



User Code (4 to 10 digits): A total of 20 User Codes and 1 one-time User code can be programmed

and stored in the lock.



User ngerprint: 20 ngerprint can be programmed and stored in the lock.



Both master and user PIN codes do not support the following combination of numbers.

IMPORTANT: Do not load batteries until lock is completely installed.

123456789

987654321

222222222

5683

568391

915683

A. Forward number sequence

B. Backward number sequence

C. Repeat number sequence

D. If

Then Contain existing code sequence

and

Parts Illustrations

Item Specifications Remarks

Battery

(Use new, non-rechargeable alkaline

batteries only.)

AA alkaline battery x4 (Not included)

Lasts up to 9 month

(10 times unlock/lock per day)

Multifunction Button

Battery Cover

Reset Button

Thumb Turn

Keypad

Fingerprint Sensor

Cylinder

WARNING: The default Master Code is 12345678. It is required that you change it to a code of your own

before programming.

WARNING: The default Master Code is 12345678. It is required that you change it to a code of your own

before programming.

Wait for

Solid Green Lights

Wait for

Green Light Flash

Succeed

Green Light Flash

Wait for

Green Light Flash

Press

New Master PIN Code New XXXXXX PIN Code

Conrmation

Wait for

Green Light Flash

Succeed

Green Light Flash

Wait for

Green Light Flash

New User PIN Code

Succeed

Green Light Flash

Wait for

Green Light Flash

Press

Change

Master

Code

Add

User

Code

Delete

User

Code

Succeed

Green Light Flash

Wait for

Green Light Flash

Wait for

Green Light Flash

New User PIN Code New User PIN Code

Enter New Duration

Time (10-99)

Succeed

Green Light Flash

Wait for

Green Light Flash

Press

Add

One-Time

Code

Adjust

Auto

Re-lock

Duration

time

Wait for

Green Light Flash

Beeper Enabled

Green Light Flash

Beeper Disabled

Press

Enable/

Disable

Beeper

Green Light Flash

Enable Away Mode Succeed

Wait for

Green Light Flash

Wait for

Green Light Flash

Enable Auto Re-lock

Mode)

Green Light Flash

Disable Auto Re-lock (Manual

Press

Away

Mode

Enable/

Disable

Auto

Re-lock

Wait for

Green Light Flash

Press

Add User

Fingerprint

Scan Fingerprint 8 Times

Each Time Succeed Along With a Short Beep

Succeed

Green Light Flash + A Long Beep

Wait for

Green Light Flash

Press

Delete User

Fingerprint

Succeed

Green Light Flash + A Long Beep

Scan Unwanted Fingerprint 1 Time

Master PIN Code

Press 2 Times

Press 1 Time Press 1 Time

New XXXXXX PIN Code

Conrmation

Press 1 Time

Press 1 Time Press 1 Time

Unwanted User PIN Code

Press 1 Time

Press

Press 1 Time

Press

Press 1 Time

Press

Press 1 Time

Press

Press 1 Time

Press 1 Time Press 1 Time

Press 1 Time

Master PIN Code

Press 2 Times

Press 1 Time

Wait for

Solid Green Lights

Master PIN Code

Press 2 Times

Press 1 Time

Master PIN Code

Press 2 Times

Press 1 Time

Wait for

Solid Green Lights

Wait for

Solid Green Lights

Master PIN Code

Press 2 Times

Press 1 Time

Wait for

Solid Green Lights

Master PIN Code

Press 2 Times

Press 1 Time

Wait for

Solid Green Lights

Master PIN Code

Press 2 Times

Press 1 Time

Wait for

Solid Green Lights

Master PIN Code

Press 2 Times

Press 1 Time

Wait for

Solid Green Lights

Master PIN Code

Press 2 Times

Press 1 Time

Wait for

Solid Green Lights

Master PIN Code

Press 2 Times

Press 1 Time

Wait for

Solid Green Lights

NOTE: When setting unsuccessful, the indicator light will ash red.

If no button is pressed for more than 10 seconds, the lock will exit programming mode.

Restore To Factory Default Settings

Quick Setup (continued)

Troubleshooting

Troubleshooting (continued)

83618 137192 14710

Real code

Random digits

21 137192 5486249

Real code

Random digits

5 137192 48

Real code

Random digits

96731286 137192 2

Real code

Random digits

MASTER CODE

Required for programming and feature settings. Master code can be used to unlock the door under away mode.

The default master code needs to be changed before programming. Property owner/manager should keep this

information condential.

AUTO LOCK

Automatically locks the deadbolt 30 seconds after unlocking.This feature is off by default.You can set the Auto

Lock time delay between 10 and 99 seconds.

WRONG ENTRY LIMIT

After 10 unsuccessful attempts at entering a invalid PIN code, the unit will shut down for 3 minutes.

SILENT MODE

The beep sounds when pressing keypad can be muted. But you will still hear low battery and system

alerts.

AWAY MODE

This is a security feature for you when you are leaving your home for vacation or long trip. Enabling

away mode will restrict all user codes and user ngerprints until master code is entered on keypad. If

the lock is unlocked by thumb turn or key, the lock will sound an alarm for 1 min. Entering master code

on keypad can disable alarm and away mode.

ONE TIME USER CODE

This code can only be used once and is automatically deleted when used.

UNLOCK WITH FAKE CODE

Any numbers can be entered before and after the real codes to prevent pincode from exposing to

strangers, but the limit included real code is 20 numbers.

Denitions

Operation

Unlocking the door from outside



Unlock by the mechanical key.



Unlock by the ngerprint.



Unlock by the Pin code.



Unlocking the door from inside

Locking the door from outside



Press any key on keypad for 2 seconds to

lock the door under manual mode.



The bolt will extend out automantically after

unlocking under auto re-lock mode.

Locking the door from inside



Rotate the thumb turn to lock position to

lock the door under manual mode.

Factory Default settings

Settings Factory Defaut

Master Code 12345678

Auto Lock Disabled

Silent Mode Disabled

Wrong Code Entry Limit 10 times

Shutdown Time (Wrong Entry 10 times) 3 mins

Away Mode Disabled



Rotate the thumb turn to unlock position.

Master/User

code

A B C



The device will be locked automatically

under auto-relock mode.

Problem Solution

The latch does not operate

correctly after installation.



Make sure the backset on the latch is set to the proper length. Refer to Installation Guide



Make sure prior to installation latch bolt is retracted and key is not in lockset when

installing the deadbolt. Refer to Installation Guide



Please restore to factory setting and enter the default Master Code to set up the

lock. Refer to User Guide

Feel a bump while turning

the thumb turn or the key?





Check if the length of mounting screws is correct.

Fail to set up the lock.





Please make sure the lock is installed correctly.





Please install fresh batteries and make sure the cable is connected correctly.





After installation, restore the lock to factory default to complete bolt direction setting.

Battery indicator keeps

ashing.





The batteries are getting low, please replace with four new batteries for the best

performance (alkaline batteries only).

Keypad not responding.





Make sure the batteries are installed properly.





The batteries are getting low if the battery indicator keeps ashing. Please replace

with four new batteries for the best performance (alkaline batteries only).





Make sure the cable is well-connected to the port, and was not damaged during

installation.





Please make sure the lock has been set up and complete the bolt direction determination.

Master Code can not be

changed.





Please refer to User Guide to restore factory settings and reprogram all codes.

What should I do if wrong

code was entered?





Press button once and continue to input code according to regular procedures.

I forgot my Master Codes.





Perform a reset in order to erase all passcodes. Once the reset is complete, all passcodes

will be erased and the Master code will return to the default master code 12345678.

Can not add a new User

Code.





Make sure the whole code entering process is completed within 10 seconds,

otherwise the unit will time out.





Make sure the Master Code has been entered correctly.





The new User Code will not be accepted when the capacity is full. Try to delete any

or some existing User Codes and then add new one(s) again. A User Code must be

at least 4 to 10 digits.

"Auto lock" does not

function.





The batteries are low on power if the battery indicator keeps ashing. Please

replace with four new batteries for the best performance (alkaline batteries only).





Please refer to User Guide to enable the Auto-Lock function.

Problem Solution

Lockset is not able to unlock

/ lock by keypad.





Make sure you have entered the correct User Code.





The battery is low if the battery indicator light keeps ashing. Please replace with

four new batteries.





Make sure the cable is rmly connected.





Check the cable for any damage that may have occurred during installation.





Make sure the batteries are properly installed. (Alkaline batteries only.)





Check the strike plate to make sure it is properly aligned and clear so the bolt can

freely move in the hole.

Lockset is unable to reset.





Please refer to User Guide to restore factory settings and reprogram all codes.





The battery is low if the battery indicator light keeps ashing. Please replace with

four new batteries.

How to operate the lockset

in darkness?





Press the lock button to activate the lockset back light.

The red indicator is still on

after setting is completed.





Check if you entered correct user codes.





Re-install the batteries.

The lockset locks when I

enter my code and unlocks

when I press the





Un-install the interior and exterior assemblies.

Before re-installation, please follow these guidelines: Refer to Installation Guide

1) Make sure the bolt is in the retracted (unlocked) position.

2) Do not have any key in the cylinder durring installation.

3) Make sure the turn piece is inserted horizontally.





Reset the unit to factory settings and reprogram the Master Code and User Codes.

I cannot remove my key

unless it is in the locked

position.





Un-install the interior and exterior assemblies.

Before re-installation, please follow these guidelines: Refer to Installation Guide

1) Make sure the bolt is in the retracted (unlocked) position.

2) Do not have any key in lock cylinder.

3) Make sure the turn piece is inserted horizontally.

Fingerprint can't unlock.





Make sure the ngerprint is registered and recognizable.

If the lock appears to be damaged or does not operate properly, please contact customer service for further assistance.