Item #1005496722 Model #HB-1912-WH Item #1005538305 Model #HB-1912-BZ USE AND CARE GUIDE Battery-Operated Motion Sensor Light Questions, problems, missing parts? Before returning to the store, call Defiant Customer Service 8 a.m. - 7 p.m., EST, Monday - Friday, 9 a.m. - 6 p.m., EST, Saturday 1-866-308-3976 HOMEDEPOT.COM THANK YOU We appreciate the trust and confidence you have placed in Defiant through the purchase of this motion security light.
Table of Contents Table of Contents........................................2 Safety Information......................................2 Precautions Warranty.....................................................3 3-Year Warranty......................................3 Specifications.............................................3 Pre-Installation...........................................3 Planning Installation...............................3 Tools That May Be Required....................3 Hardware Included.....
Warranty 3-YEAR WARRANTY Contact the Customer Service Team at 1-866-308-3976 or visit www.homedepot.com. Specifications Detection Range Up to 33 ft. (10 meters) Sensing angle Up to 180° LED Lumens 1200 lumens Operating temperature -13°F to +113°F (-25° C to +45° C) Power requirements 4 Alkaline “D” cell batteries - 1.5V (not included) Pre-Installation PLANNING INSTALLATION Before installing the light fixture, ensure that all parts are present (see Hardware Included on page 4).
Pre-Installation (continued) HARDWARE INCLUDED NOTE: Hardware shown is not to scale.
Installation 1 Determining the Mounting Location □ Determine the mounting location - wall or eave mount. Wall mount Eave mount 2 Removing the Mounting Plate NOTE: This fixture comes with a mounting plate (C). It is pre-assembled on the light fixture (B) for shipping. □ Gently pull the bottom tab (1) of the wall mounting plate (C) away from the light body (B).
Installation (continued) the Mounting Plate 4 Installing A. Wall Mount □ □ □ □ Remove the two rubber gaskets (2) from mounting plate (C). Place the mounting plate (C) against the wall with the word “UP” facing you (see illustration). Ensure the mounting plate (C) is level. Mark the hole locations. If mounting to a wooden surface like a deck, you can install the mounting screws (AA) through the mounting plate (C) and into the wood with a screwdriver, or with a drill and bit driver.
Installation (continued) the Mounting Plate Mounting the Light Fixture 6 Installing 7 B. Eave or Ceiling Mount □ □ □ Place the mounting plate (C) against the ceiling. Mark the hole locations. If mounting to a wooden surface like a deck, you can install the mounting screws (AA) through the mounting plate (C) and into the wood with a screwdriver, or with a drill and bit driver. You can also drill two pilot holes into the wood mounting surface with a 1/8 inch drill bit and then install the screws.
Operation (continued) 2 Adjusting the Sensor Head □ The motion sensor gets a full 180° of coverage, so it senses from wall to wall. However, if the sensor is mounted on a corner and you would like additional coverage on one side or the other, the sensor (D) can be rotated left and right. 3 Adjusting the Control Settings Adjusting The DUSK LEARN Adjusting The Selector Switch ECO 0 (DUSK LEARN) DUSK LEARN Your motion sensor light is factory preset to only work after dusk.
Operation (continued) 4 Using the Diffuser Panels If you want to reduce the glare of the lights, attach the diffuser panels (CC) to the lamp heads (A) as shown below. This also prevents the LEDs from being seen during daylight hours. Some people may prefer the appearance of the light fixture with the diffuser panels in place. To remove the diffuser panels (CC), first hold the diffuser panel from the front.
Troubleshooting Problem The light will not come on. Possible Cause □ Daylight turn-off (photocell) is in effect. □ □ The motion sensor is out of coverage area. Batteries are dead. Batteries may be incorrectly installed. □ □ The motion sensor may be installed in a relatively dark location. □ □ DUSK LEARN was set in daylight conditions. □ □ The motion sensor may be sensing small animals or automobile traffic, or other heat sources. Strong wind may activate the sensor.
Questions, problems, missing parts? Before returning to the store, call Defiant Customer Service 8 a.m. - 7 p.m., EST, Monday-Friday, 9 a.m. - 6 p.m., EST, Saturday 1-866-308-3976 HOMEDEPOT.COM Retain this manual for future use.