Item #1001-090-469 Model #THD-1000 USE AND CARE GUIDE WIRELESS HOME PROTECTION SYSTEM Questions, problems, missing parts? Before returning to the store, call Customer Service 8 a.m. - 4:30 p.m., CST, Monday - Friday 844-212-0200 HOMEDEPOT.COM THANK YOU We appreciate the trust and confidence you have placed in Defiant through the purchase of this wireless home protection system. We strive to continually create quality products designed to enhance your home.
Quick Start Guide STEP: 1 INSTALLING THE BATTERIES AND POWERING UP THE SYSTEM □□ □□ □□ □□ Install two AAA batteries (not included) into the door/ window sensor. Install one 9V battery (not included) into the motion sensor. The smart panel is supplied with a demonstration switch to show the LCD display panel working, while the unit is in its packaging. Before powering up the Smart Panel, remove the wire for this switch by unscrewing the battery compartment and removing the cover.
Safety Information Retain this manual for future reference. Even the most advanced alarm systems cannot guarantee 100% protection against burglary or environmental problems. All alarm systems are subject to possible compromise or failure-to-warn for a variety of reasons. You may encounter problems with your system if: □□ The siren is not placed within hearing range or is in a remote part of the premises. □□ The sensors are placed behind doors or other obstacles.
Safety Information (continued) FCC REGULATION This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Pre-Installation (continued) SPECIFICATIONS Smart Panel Motion Sensor Power Source AC adaptor Power Source 9V alkaline battery Back-up Power 9V Alkaline Battery RF Working Trans. Freq. 433.92MHz +/-0.5MHz Sensor Numbers Unlimited PIR Detection Angle <110 Degree (@9VDC) House Code 4 Jumpers PIR Detection Range “H”:< 15M(50ft)“M”:< 6M(20ft)“L”:< 4M(13ft) Operating Frequencies 433.92MHz +/-0.
Installation Wall mounting the smart panel and tamperproof switch 1 2 □□ First cut out the mounting template for the Smart Panel along with the area which is marked out for the position of the tamperproof magnet (see below). Powering up the Smart Panel controller NOTE: The Smart Panel is supplied with a demonstration switch to show the LCD display panel working while the unit is in its packaging. Before powering up the Smart Panel, remove the wire for this switch as described below.
Installation (continued) UNDERSTANDING THE BATTERY AND AC ADAPTOR ICON Battery Icons: Full - Battery icon shows when the AC power supply is unplugged or interrupted. 9V battery functions as BACK-UP only and the Low symbol means LOW BATTERY. The LCD backlight flashes YELLOW for 30 seconds and the Low battery icon will blink until the new battery is replaced or the main power supply (with AC adaptor) is plugged in.
Using the Panic Alarm Pressing the and buttons at the same time on either the keypad or the key remote control will immediately transmit an alarm signal to the Smart Panel, activating the siren, and transmitting an alarm signal to any optional response devices (Auto Dialer, Outdoor Bell Box & GSM Device), to request emergency assistance. To disarm the Panic alarm: □□ On the Smart Panel: Enter your 4-digit PIN followed by the Enter button to exit from the Panic alarm.
Operating in ARM Mode (continued) ADJUSTING EXIT DELAY Step Procedure Example 1 Ensure you are in STANDBY mode by entering the default PIN of 1 2 3 4 OR your new 4-digit PIN and pressing the Enter button. The Smart Panel displays this image when in STANDY mode. One beep indicates that you entered a valid PIN. Three beeps indicate that an invalid operation was performed. 2 Enter the default PIN of 1 2 3 4 OR your new 4-digit PIN of your choosing. Press the Enter button.
Operating in ARM Mode (continued) ADJUSTING THE ALARM DURATION Step Procedure Example 1 Ensure you are in STANDBY mode by entering the default PIN of 1 2 3 4 OR your new 4-digit PIN and pressing the Enter button. The Smart Panel displays this image when in STANDY mode. One beep indicates that you entered a valid PIN. Three beeps indicate that an invalid operation was performed. 2 Enter the default PIN of 1 2 3 4 OR your new 4-digit PIN of your choosing. Press the Enter button.
Operating in ARM Mode (continued) When in ARM mode, the Smart Panel flashes RED every 5 seconds, acting as a deterrent to potential intruders. However, if an intruder is detected the panel continuously and rapidly flashes RED. Once an intrusion has occurred (with the zone triggered under ARM status), the alarm siren sounds and the Smart Panel flashes RED every 1.5 seconds and indicates the triggered zone.
Operating in Standby Mode (continued) 3 Entry delay 30 seconds There are 30 seconds of entry delay time with a visual countdown for disarming. Once an intrusion has occurred (zone triggered under ARM status), the alarm siren sounds for 1 minute and the Smart Panel flashes RED every 1.5 seconds with the triggered zone indicated, until the system is disarmed. To disarm the system, enter the 4-Digit PIN or press control.
Operating in Alert Alert Mode (continued) EXITING ALERT MODE On the Smart Panel: Enter your 4-digit PIN followed by Enter to exit ALERT mode. On the Key Fob Remote Control: Press to exit ALERT mode. ZONE SETTINGS Programming each zone in ALERT mode: Step Procedure Example 1 Ensure you are in STANDBY mode by entering the default PIN of 1 2 3 4 OR your new 4-digit PIN and pressing the Enter button. The Smart Panel displays this image when in STANDY mode. One beep indicates that you entered a valid PIN.
Operating in Home Mode There are default settings that allow the system to operate after opening the package. These settings can be adjusted to suit your individual requirements. The HOME mode ( ) allows the system to operate in both ARM and ALERT modes in different zones. HOME mode default setting: Sensor Zone Status (MODE) Door/Window Sensor 1 ALERT Door/Window Sensor 2 ALERT Motion Sensor 8 ARM ENTERING HOME MODE On the Key Fob Remote Control: Press to activate.
Operating in Home Mode (continued) 3 Press and Toggle 1 2 3 4 5 6 7 8 to turn each zone in different mode: to enter HOME mode. indicates ALERT mode for a zone indicates ARM mode for a zone indicates the zone is turned OFF and the number will not appear The Smart Panel displays this image: 4 Press the Enter button to confirm the setting and return the Smart Panel to STANDBY.
Installing the Sensors (continued) INSTALLING THE MOTION SENSOR The Motion Sensor is designed to sense movement in a given area. NOTE: It is best if pets are not allowed onto higher surfaces so that the sensors are not triggered unnecessarily (no more than 1 m/3.3 ft. high). Step 1: Powering up the Motion Sensor □□ Remove the battery cover, insert and connect a 9V battery as shown in diagram below and replace the cover. (Requires 1 x 9V battery).
Installing the Sensors (continued) Step 5: Mounting using Screws □□ Hold the enclosed mounting template against the wall at the selected location and mark the points for drilling. □□ Drill the holes and insert wall plugs. □□ Attach the bracket to the mounting surface with the screws provided.
Using the Key Fob Remote Control (continued) OPERATING THE KEY FOB REMOTE CONTROL The remote can be used to arm, disarm, and operate the system instantly. □□ ARM – Arms the system, triggering the preset exit delay. When triggered, the Smart Panel’s LED light will flash Red and indicate the triggered zone. □□ DISARM – Disarms the system instantly and the system will return to Standby mode. □□ ALERT – Puts the system into Alert mode and a chime will sound if any of the sensors are triggered.
Using the Key Fob Remote Control (continued) QUERYING THE ID NUMBER OF A REMOTE CONTROL The ID number of a Remote Control device can be identified as follows: Step Procedure Example 1 Ensure you are in STANDBY mode by entering the default PIN of 1 2 3 4 OR your new 4-digit PIN and pressing the Enter button. TThe Smart Panel displays this image when in STANDY mode. One beep indicates that you entered a valid PIN. Three beeps indicate that an invalid operation was performed.
Zone Code Settings Sensors are supplied with pre-assigned Zone settings to make setup easy – the Door/Window Sensors are pre-assigned to Zones 1 & 2 and the Motion Sensor to Zone 8. To assign a Sensor to a different zone, change the Zone Code on the Sensor by completing these steps: 1. Remove the Jumper compartment cover to access the Zone Code Jumper on each Sensor. 2. Pull out the Jumper and reassign it to the new Zone (Zones 1 to 8) as shown in the diagram below. 3. Replace Jumper compartment cover.
Mounting Template 84mm (3.31inch) Mount tamperproof magnet here 3 1 2 36mm （1.42inch） 43mm (1.69inch) 16mm (0.63inch) 43mm (1.69inch) 16mm (0.63inch) *For details please refer to user guide installation section. 21 HOMEDEPOT.COM Please contact 844-212-0200 for further assistance.
Questions, problems, missing parts? Before returning to the store, call Customer Service 8 a.m. - 4:30 p.m., CST, Monday - Friday 844-212-0200 HOMEDEPOT.COM Retain this manual for future use.
