Parts General Assembly - 1520 Model Main Driveline (pg. 55-56) Hitch Assembly (pg. 45) Wing Driveline (pg. 57) Right Wing Assembly (pg. 43) Wing Lift Cylinder, 3” x 16” (pg. 53) Rephasing Cylinder, 3” x 8” (pg. 54) Center Shield Assembly (pg. 46) Center Section Assembly (pg. 41-42) Right Wheel Strut (Walking Axle also available) (pg. 48) Tie Bar Assembly (pg. 41) Center Driveline (pg. 58) Wing Driveline (pg. 57) Pan, Blades, & Hardware (pg. 50) Left Wing Assembly (pg.
Center Frame Assembly Use non-removable loctite when replacing splitter box bolt hardware.
Center Frame Assembly 118901 - Lynch Pin, 3/6” x 1-1/2” (1) 118378 - Bolt, 5/8”x 1-3/4” (2) 118447 - Lock Nut, 5/8” GRC-Unitorque (2) 118537 - Flat Washer, 5/8” SAE (2) 501005 - Urethane Bumper (2) Counter Clockwise 170063 - Gearbox 1000 RPM OR 170017 - Gearbox 540 RPM Clockwise 170061 - Gearbox 1000 RPM OR 170019 - Gearbox 540 RPM 118983 - Bolt, 1/4” x 3/4” (4) 118555 - Flat Washer, 1/4” (4) 133100 - Manual Holder (1) 118555 - Flat Washer, 1/4” (4) 118483 - Lock Nut, 1/4” - Unitorque (4) 118483 - Lock Nu
Right / Left Wing Assembly (Right Wing Assembly Shown) 500869 - Wing Skid Shoe - LH (1) 118729 - Lock Nut, 1/2” GRC Unitorque (6) 118512 - Flat Washer, 1/2” (6) 500608 - 5 Bolt Chain Safety Bar (3) 500912 - Cable, 1/4” x 71” (1) (Optional) 118642 - Carriage Bolt, 1/2” x 1-1/4” (6) 500868 - Wing Skid Shoe - RH (1) 500600 - 3 Bolt Chain Safety Bar (2) 118417 - Lock Nut, 3/8” UNC GR5 (25) 118511 - Flat Washer, 3/8” (25) 118964 - Carriage Bolt, 3/8” x 3” (25) Wing Driveline 160002 - (1000 / 540 RPM) 5002
Counterweight Assembly (1020 Model Only) 118966 - Roll Pin, 5/16” x 1-3/4” (2) 500837 - Hinge Pin, 1-3/16” x 97-3/4” (1) 500265 - Counterweight Frame (1) 500870 - Counterweight Skid (1) 118984 - Bolt, 1-1/4” x 3” GR5 (2) 500257 - Bolt Plate (2) 118445 - Lock Nut, 1-1/4” GR5 (2) 117436 - Bolt, 1” x 8-1/2” GR5 (6) 118417 - Lock Nut, 3/8” UNC GR5 (4) 306356 - Chain, 5/16” - 11 Links (4) 118511 - Flat Washer, 3/8” (8) 118136 - Bolt, 3/8” x 1-1/2” (4) 500869 - Wing Skid Shoe - LH (1) 500868 - Wing Skid Shoe
Hitch Assembly 143111 - Hose Holder (1) 118024 - Bolt, 5/8” x 1-1/2” UNC (1) 118514 - Washer, 5/8” (1) 500300 - Hitch Frame (1) 118447 - Lock Nut, 5/8” UNC Unitorque (1) 118422 - Lock Nut, 3/4” UNC (3) 118516 - Flat Washer, 3/4” (6) 500328 - Jack Holder (1) 118043 - Bolt, 3/4” x 2” UNC (3) 118336 - Grease Fitting, 1/4” (1) 117111 Bushing (2) 118962 - Lock Nut, 1-1/4” UNF GR8 (1) 131206 - Flat Washer, 1-1/4” SAE (1) 500312 - Swivel Hitch (1) 132051 - Sidewind Jack (1) 118929 - Lock Pin, 3/8” x 1-1/2”
Center Shield and Hydraulic Hose Clamps 500715 - Center Shield Assembly (1) - includes 133093 - Capscrew, M8 x 1.25 x 30mm (2) 133092 - Plastic Handle (1) 133094 - Nut, M8 x 1.
Rockshaft Assembly 500840 - Transport Lock Rockshaft Suspension Detail 243500 - Lock Pin, 5/16” x 2-1/2” Preloading of rubber spring required on all strut assemblies. Exposed thread length should be approximately 1/2” when using correct hardware.
Wheel Strut Assemblies Upper Strut Common Wing Suspension Detail Preloading of rubber spring required on all strut assemblies. Exposed thread length should be approximately 3/8” when using correct hardware.
Hub & Spindle 131390 - Hub & Spindle Assembly 131382 - Spindle, S517-1 (1) This model comes with a three piece seal and different hub. All other components common with 131380 Hub/Spindle Assembly.
Note: See Gearbox Details pg. 60-64 for correct Cutter Pan Mounting Hardware including nuts, coned washers, & cotter pins.
Hydraulic Schematics Height Control Cylinders - 1520 Model (Note: Cylinder details are shown on a separate page) 141581 - Coupler, Tip (2) 141515 - Nipple, (2) 126666 - Hose, 3/8 x 192” 126667 - Hose, 3/8 x 246” 141504 - Elbow, 90° 141515 - Nipple 126503 - Hose, 3/8 x 82” 141616 - Elbow, 45° (4) 122836 - Wing Height Cylinder (3-1/4” x 8”x 1-1/4”) 122830 - Wing Height Cylinder (3” x 8”x 1-1/4”) 122850 - Center Height Cylinder, (3-1/2” x 8” x 1-1/4”) 126626 - Hose, 3/8 x 168” Wing Lift Cylinders - 1520 Mo
Hydraulic Schematics Height Control Cylinders - 1020 Model Hydraulic Fitting Guide (Note: Cylinder details are shown on a separate page) 141581 - Coupler, Tip - 3/4 ORB F 141581 - Coupler, Tip (2) 141515 - Nipple, (2) 141506 - Orifice, Plate 0.
Cylinders 122875 - Wing Lift Cylinder (with Internal Compression Spring) - 3” x 16” x 1-1/2” 122879 - Rod/Clevis - 1-1/2” x 16” 118796 - Bolt, Shoulder - 1/2” UNC 122556 - Cap, Open - 3” x 1-1/2” 118924 -Flat Washer - .591” ID x .905” OD 122558 - Lock Ring, 3” 118930 - Pin, - 1” x 2-13/16” 122877 - Barrel, 3” x 16” 143500 - Spring, Compression 122881 - Piston, 3” 118441 - Lock Nut, 7/8 UNF Unitorque 122523 - Seal Kit 118930 - Pin, - 1” x 2-13/16” 118924 - Flat Washer - .591” ID x .
Cylinders 122836 - Wing Height Control Cylinder (with Rephasing Grooves) - 3-1/4” x 8” x 1-1/4” (1520 Model - Left Wing, 1020 Model - Right Wing) 118796 - Bolt, Shoulder - 1/2” UNC 118924 -Flat Washer - .591” ID x .
Drivelines 160000 - 1000 PTO Driveline - Main Driveline with 80° CV Joint - B&P SFT S6 160078 - Sleeve 160069 - Shield 160073 - Screw (6) Optional 160102 - Yoke, S6 -1 3/4 20 spline (c/w Sleeve) 160070 - Ring 160071 - Shield 160050 - Yoke, S6 -1 3/8 21 spline (c/w Sleeve) 160051 Cross Kit 160055 - CV Body, S6 160054 - Yoke, S6 160056 - Tube 160072 - Shield 160064 - Ring 160065 - Cone/Tube 160053 Grease Fitting 160073 Screw (4) 160073 - Screw (4) 160058 Pin, Roll 160086 - Shield Kit 160082 Outer Sh
Drivelines 160001 - 540 PTO Driveline - Main Driveline with 80° CV Joint - B&P SFT S8 160108 - Sleeve 160104 - Shield 160073 - Screw (6) 160105 - Ring 160106 - Shield 160087 - Yoke, S8 -1 3/8 6 spline (c/w Sleeve) 160088 Cross Kit 160091 - CV Body, S8 160090 - Yoke, S8 160092 - Tube 160107 - Shield 160099 - Ring 160100 - Cone/Tube 160053 Grease Fitting 160073 Screw (4) 160073 - Screw (4) 160094 Pin, Roll 160116 - Shield Kit 160112 Outer Shaft (c/w Shielding) 160113 Inner Shaft (c/w Shielding) 16006
Drivelines 160010 - 540/1000 PTO Driveline - Wing Driveline with Torque Limiter - B&P SFT S6 160061 Cross Kit 160151 - Torque Limiter - 950 NM (Detail - pg.
Drivelines 160003 - 1000 PTO Driveline - Center Driveline with 950 NM Torque Limiter - B&P S5 160005 - 540 PTO Driveline - Center Driveline with 1450 NM Torque Limiter - B&P S5 160151 - Torque Limiter - 950 NM 1000 PTO Driveline (Detail - pg. 59) - OR 160155 - Torque Limiter - 1450 NM 540 PTO Driveline (Detail - pg.
Drivelines 160151 - Torque Limiter 950 NM - Wing 540/1000 PTO 950 NM - Center 1000 PTO 160155 - Torque Limiter 1450 NM - Center 540 PTO Note: All parts are common with the exception of the torque limiter spring.
Gearboxes 170011 - 1000 RPM PTO Gearbox - 8146 - (1.31:1) -OR170021 - 540 RPM PTO Gearbox - 8146 - (1:1.16) Part # - (Qty) Description 1000 RPM PTO 170143 - Gear Set (1.31:1) 170142 - (01) Shaft, 8146 170123 - (01) Seal -OR540 RPM PTO 170155 - Gear Set (1:1.
Gearboxes 170003 - 1000 RPM PTO Gearbox - 3070 (1:1.25) - Clockwise Rotation -OR170013 - 540 RPM PTO Gearbox - 3070 (1:1.
Gearboxes 170005 - 1000 RPM PTO Gearbox - 3070 (1:1.25) - Counter Clockwise Rotation -OR170015 - 540 RPM PTO Gearbox - 3070 (1:1.
Gearboxes 170163 - 1000 RPM PTO Gearbox - 3080 (1:1) - Counter Clockwise Rotation -OR170017 - 540 RPM PTO Gearbox - 3080 (1.
Gearboxes 170161 - 1000 RPM PTO Gearbox - 3080 (1:1) - Clockwise Rotation -OR170019 - 540 RPM PTO Gearbox - 3080 (1.
Optional Light Kit - Location Typical Light Wire Routing - 1020 Typical Light Wire Routing - 1520 LH Wiring LH Wiring RH Wiring RH Wiring Typical Light Bracket Assembly 118011 - Bolt, 1/2” x 1-1/2” GR5 (4) 118756 - Bolt, 1/4” x 1-1/4” GR5 (8) 500926 - Light Mounting Bracket (2) 118729 - Lock Nut, 1/2” GRC - Unitorque (4) 118483 - Lock Nut, 1/4” GR5 - Unitorque (8) Note: Install lights with amber light to outside, covered lens facing forward.
Optional Light Kit - Wiring 501533 - Light Kit Includes: • Lights (Left & Right) • 7 Pole Plug Connector Note: All spliced ends should be soldered. • 16 Gauge Wiring White • Mounting Brackets • All Required Hardware Brown Green Yellow Red RH Green Red Red LH Green Black Black White White 129027 - 7 Pin Plug 129058 - LH Light, 4 Wire 129059 - RH Light, 4 Wire 15’ Model 129066 - Wire, 4 x 16 ga. - 25’ 129065 - Wire, 4 x 16 ga. - 24’ 10’ Model 129067 - Wire, 4 x 16 ga. - 21’ 129043 - 16 ga.
Optional Winch Kit 501534 - Winch Kit (Hardware Included) 129063 - Winch, 1500 LB (1) 118511 - Flat Washer, 3/8 (3) 118005 - Bolt, 3/8” x 1” GR5 (3) 118417 - Lock Nut, 3/8” GR5 (3) 500916 - Cable/Hook Assembly (1) 500917 - Pulley Block (1) 500925 - Winch Mount Assembly (1) 118073 - Bolt, 1” x 3-1/2” UNC GR8 (2) 118456 - Lock Nut, 1” UNC GR5 (4) 118103 - Bolt, 1” x 2-1/2” UNC GR5 (2) 500920 - Hook Plate Assembly (2) Note: Refer to operation and safety instructions found in the operators section of the manua
Optional Toolbox 501536 - Toolbox/Blade Storage Kit (Hardware Included) 500852 - SMV Sign Extension (1) 118483 - Lock Nut, 1/4” GRC - Unitorque (2) 118983 - Bolt, 1/4” x 3/4” UNC GR5 (2) 133103 - Toolbox, 8-3/4” x 32” x 9 1/2” (1) 118009 - Bolt, 1/2” x 1-1/4” UNC GR5 (4) 118512 - Flat Washer, 1/2” (4) 118729 - Lock Nut, 1/2” GRC - Unitorque (4) 500851 - Toolbox Mount Bracket -LH (1) 500850 - Toolbox Mount Bracket -RH (1) 118447 - Lock Nut, 5/8” GRC - Unitorque (4) 118514 - Flat Washer, 5/8 (4) 118026 - B
Warranty 2 Year Limited Warranty Degelman Industries Ltd. (“Degelman”) warrants to the original purchaser of a new 1020/1520 Degelman Rotary Cutter, purchased from an authorized Degelman dealer, that the equipment will be free from defects in material and workmanship for a period of two (2) years from the date of delivery, for non-commercial use (including farm, institutional, government, and municipality) and (1) year from the date of delivery for commercial use.
