mini Wiring & Installation Instructions V06/05/08
proxSafe mini © Copyright 2008 by deister electronic GmbH All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without prior written permission of deister electronic GmbH. deister electronic GmbH reserves the right to make changes to any and all parts of this documentation without obligation to notify any person or entity of such changes.
proxSafe mini mini Contents 1. Technical data ........................................................ 4 1.1 1.2 1.3 1.3.1 1.3.2 1.4 1.5 Electrical characteristics..................................................................................4 Housing .......................................................................................................4 Customer interfaces .......................................................................................5 Communication .........................
proxSafe mini 1. Technical data 1.1 Electrical characteristics UB: In: Imax: 1.2 12-13,8V/DC* 50mA (Standby) 2,3A (during closing or opening, if no other components activated) Housing Width: 440mm without mounting angle 484mm with mounting angle Height: 133mm Depth: 173mm keyRing Seal keyTag proxCylinder * 13,8 V needed if a battery is connected and needs to be charged 12 V if no battery charging is required. This refers to all voltages in the manual.
proxSafe mini mini 1.3 Customer interfaces Figure 1: interfaces 1.3.1 Communication RS485 deBus, 9600 Baud, 1 startbit, no parity, 1 stopbit, 8 bits RJ45 Connector Connect TERMINAL of the multiplexer to HOST (e.g.
proxSafe mini MUX IN: Data line from previous multiplexer Pin 1 2 3 4 5 6 7 8 Description nc nc GND GND +UB (13,8V) +UB (13,8V) RS485 B RS485 A MUX OUT: Data line to next multiplexer Pin 1 2 3 4 5 6 7 8 Description nc nc GND GND +UB (13,8V) +UB (13,8V) RS485 B RS485 A 1.3.2 Power 3-PinConnector, green RM5 POWER IN: Power line from previous multiplexer or from power supply Pin 1 2 3 Description nc 13,8V GND 3-Pin Connector, green RM5 POWER OUT: Power line to next multiplexer Pin 1 2 3 1.
proxSafe mini mini 1.5 Battery 2-Pin Field Wiring Connector, Battery Pin 1 2 Description ACCU + GND 2. Wiring diagram The deBus supports a maximum of 32 devices. The amount of necessary power supplies is depending on the application (e.g. if shutters are used or not). In this example an SNG3 adapter is used to connect the data line to the HOST.
proxSafe mini 3. General proxSafe mini is part of a keyTag management system. With proxSafe mini you can handle up to 8 proxCylinders in one device. Connection of the proxCylinders is done by RJ45 connectors.
proxSafe mini mini 4. Implementing hints You will find the implementing hints in the debus protocol for the proxsafe mini (available on request). 5. Shutter is blocked If the terminal gives a signal to the multiplexer to close the shutter and the shutter is blocked, the multiplexer tries closing the shutter for three times. If the third attempt failed, the shutter remains in this position. The device alert flag is set (see error codes in debus protocol description).
proxSafe mini 6. Emergency unlock If normal operation failed (e.g. processor does not work) to get keys out, an emergency unlock is integrated. The components for emergency unlock are at the backside of the proxSafe mini. Jack for unlocking the shutter Pin1: GND The first step is to open the shutter. The shutter is protected against opening by hand.
proxSafe mini mini After the shutter has been opened this way, in a second step the emergency unlock for the proxCylinders must now be activated separately as follows: Jack for emergency unlock Pin 1: GND To activate this emergency unlock, the jack (red marked in the picture above) must be connected to the emergency opening box with the 4-pole cable (enclosed) as follows: Pin 1 2 3 4 Connection GND 12 -13,8V/DC 12 -13,8V/DC 12 -13,8V/DC While this jack is connected and the switch of the emergency box i
proxSafe mini Emergency-switch Battery status Emergency cable Battery charge Emergency opening box with two different cables (one 2-pole-cable and one 4-pole cable) 12 ps_mini_wi_en 29/05/08
proxSafe mini mini 7. Regulatory notices 7.1 Europe Hereby, deister electronic GmbH declares that this equipment - if used according to the instructions - is in compliance with the essential requirements and other relevant provisions of the RTTE Directive 1999/5/ EC. A complete declaration of conformity can be requested at: info@deister-gmbh.de Approved for use in all European countries. 7.
proxSafe mini 7.3 FCC Notice To comply with FCC part 15 rules in the United States, the system must be professionally installed to ensure compliance with the Part 15 certification. It is the responsibility of the operator and professional installer to ensure that only certified systems are deployed in the United States. The use of the system in any other combination (such as co-located antennas transmitting the same information) is expressly forbidden. 7.
proxSafe mini mini Notes: V29/05/08 ps_mini_wi_en 15
proxSafe mini Notes: 16 ps_mini_wi_en 29/05/08
proxSafe mini mini Germany: deister electronic GmbH Hermann-Bahlsen Str. 11 30890 Barsinghausen Tel.: +49 (0) 51 05 - 51 61 11 Fax: +49 (0) 51 05 - 51 62 17 info@deister-gmbh.de www.deister.com Belgien & Luxemburg: deister electronic office Business Park E 19 Battelsesteenweg 455/A 2800 Mechelen Tel.: +32 (0) 15 - 28 09 68 Fax: +32 (0) 15 - 28 09 71 info@benelux.deister.com Frankreich: deister electronic france 101 rue Pierre Semard 92320 Chatillon Tel.
