Installation Guide

ManualsBrandsDelaney Hardware ManualsDoor HardwareZW300 SmartHome Chrome Single-Cylinder Deadbolt 1-Cylinder Electronic Deadbolt Lighted Keypad Touchscreen Built-In Z-Wave

USER MANUAL

TEMPLATE

45 40 35

1-3/4" 1-9/16" 1-3/8"

Fit here on door edge

FOR BACKSET 70mm (2-3/4”)

FOR BACKSET 60mm (2-3/8”)

Mark Ø1" (25.4mm) hole at

center of door edge.

Ø54mm (2-1/8")

Attention : Please do not use the "electronic" screwdriver for installation.

Product :

Purchase Date :

Limited Warranty Statements

1. Warranty

The manufacturer warrants the Product to be free

from defects in material and workmanship for a period of 12 months

from the original date of purchase.

If you discover a defect in the Product covered by this warranty, we will repair or

replace the item at our option using new or refurbished components.

2. Exclusions

This warranty covers defects in manufacturing discovered while using the

Products as recommended by The manufacturer rather than occurred by the act

of God, and damages caused by misuse, abuse, and unauthorized modification.

3. Limited of Liability

The manufacturer will not be held liable for incidental or consequential losses or

damages to any act of God.

4. Reminder

Service requirement shall subject to the presentation of this warranty card

and defective parts to the manufacturer.

The warranty card will not be reissued if lost.

TOUCHPAD

ELECTRONIC DEADBOLT LOCK

Summary of content (18 pages)

PAGE 1
TEMPLATE Fit here on door edge 45 40 35 1-3/4" 1-9/16" 1-3/8" Mark Ø1" (25.4mm) hole at center of door edge. Limited Warranty Statements 1. Warranty The manufacturer warrants the Product to be free from defects in material and workmanship for a period of 12 months from the original date of purchase. If you discover a defect in the Product covered by this warranty, we will repair or replace the item at our option using new or refurbished components. TOUCHPAD ELECTRONIC DEADBOLT LOCK 2.
PAGE 2
PACKAGE CONTENTS H G C J L F D E B A I PART A B C D E F G H I J K L K DESCRIPTION QUANTITY Key 2 Cylinder 1 Deadbolt Touchpad Assembly 1 Deadbolt Latch 1 Strike Plate 1 Mounting Plate Receiver Assembly 1 Battery Cover 1 Drive-in Sleeve 1 1 Machine Screws 3 Wood Screws 5 Deadbolt Chassis Screws 2 1
PAGE 3
HARDWARE SCREWS CONTENTS J K Machine Screws Wood Screws Qty. 3 Qty. 5 L Deadbolt Chassis Screws Qty. 2 LATCH BACKSET ADJUSTMENT Remarks: Please notice the slight differences in the latch box between two different backsets.
PAGE 4
ASSEMBLY INSTRUCTIONS 1. Backset Determination Backset is a distance from door edge to centre of hole on door face. Adjustable latch fits both backset of 2 3/8" (60 mm) and 2 3/4" (70 mm). 2. Change Latch Face Determine which latch mounting method will be used and make necessary adjustments. No adjustment required for square latch face plate. 1 2 D a a. Use a flat screwdriver to separate the face plate. b. Snap selected latch face plate onto back plate.
PAGE 5
ASSEMBLY INSTRUCTIONS 3. Latch Backset Adjustment Determine if the latch (D) needs to be adjusted to the 2 3/4" (70 mm) backset. To adjust, rotate the latch until it stops. Reverse the direction to return to the 2 3/8" (60 mm) backset. 3 D 2 3/4" (70 mm) 4. Mark the Door with Template Select the height and backset as desired on the door face; use the TEMPLATE as an indication to mark the centre of the circle on the door face and the centre of the door edge. 5.
PAGE 6
ASSEMBLY INSTRUCTIONS 6. Mark the Outline of Latch Faceplate Insert the latch (D) and ensure it is parallel to the door face. Mark the outline of the faceplate, then take out the latch (D). 6 D You need to stay this way up when inserting the latch. Make sure the cross in the latch is on the bottom. 7. Chisel Space for Latch Faceplate Chisel 5/32" (4 mm) deep along the outline to allow the faceplate to be aligned with the door edge.
PAGE 7
ASSEMBLY INSTRUCTIONS Install Drive-in Latch Drive the latch (D) into the hole on edge of door. 8.1 D 9. Mark the Outline of Strike To identify the centre of strike: close the door to lay the latchbolt against the door frame. Mark the centre line on the doorframe exactly opposite the latch hole in the door edge. 10.1 Drill Hole on Door Frame Measure one half of door thickness from door stop and vertically mark centre line of strike. Drill 1" (25.4 mm) hole, 1" (25.
PAGE 8
ASSEMBLY INSTRUCTIONS 11. Install Strike on Door Frame Install the strike plate (E) into your door frame and tighten with wood screws (K). 11 E Hardware Used K Wood screws x2 K 12. Install Touchpad Assembly Make sure the latch bolt is retracted. 12 D 13. Install Touchpad Assembly Install cylinder (B) into the deadbolt touchpad assembly (C) with tailpiece in horizontal position inserted through hub of the latch.
PAGE 9
ASSEMBLY INSTRUCTIONS 14. Install Touchpad Assembly 14 Pass the IC wire under the latch (D) to the interior side of the door, and insert the tailpiece through the cross-shaped crank of the latch. C D horizontal position IC wire B 15. Install Inside Mounting Plate Pass the IC wire through the wire hole of the mounting plate (F). Fix the mounting plate (F) with screws (L). If outside lock assembly is lopsided, please loosen the screws to adjust its position and tighten the screws again.
PAGE 10
ASSEMBLY INSTRUCTIONS 17. Adjust Thumb Turn Piece Rotate the thumb turn piece to the LEFT at 45 degrees for right-handed doors. Rotate the thumb turn piece to the RIGHT at 45 degrees for left-handed doors. 17 G For left-handed For right-handed door door 18. Install Receiver Module 18 Remove the battery cover (H) (push it up first then pull it out). H G   19. Install Receiver Module Connect the IC wire into the back of the receiver module.
PAGE 11
ASSEMBLY INSTRUCTIONS 20. Insert Batteries Insert 4 (AA) 1.5 V alkaline batteries and slide the battery cover (H) back onto the receiver module (G). Remarks: (1) Alkaline batteries are recommended in order to stabilize the power supply. If you don't use alkaline, battery performance will be reduced greatly. (2) All settings will be retained in the memory even if the batteries are completed dead.
PAGE 12
OPERATIONAL INTERFACE  1 2 3 4 5 6 7 8 9     0     Programming Button Programming button is for setting function.  Lock Btutton Lock Button is for lock and unlock function.  Cylinder To lock/unlock the lockset by key from outside.  Washer Prevents water from permeating into lockset.  Battery Lid Slide the lid to change the batteries.  Battery Holder Four AA (1.5 V) alkaline batteries.  R Button (Reset) Restore default settings.
PAGE 13
OPERATING INSTRUCTIONS ˙ Keep the door open while programming to avoid being locked out accidentally. The lock contains one factory-preset user code but can be programmed to store up to a total of six additional unique user codes. ˙ Codes can be added and deleted at any time. For first-time programming, use factory default programming code. It’s recommended to change the default programming code and default user code right after you install the lock. Every programming step should be done within 6 seconds.
PAGE 14
OPERATING INSTRUCTIONS Default programming code (PC): 0000 Default user code (UC): 1234 Your new programming code (PC) ____________ Your new user code (UC) ___________________ The same programming code and user code cannot be accepted. The lock will cease operation if unauthorized codes are entered over 5 times. The system will unfreeze after 45 seconds. 1. Door Handling Identification Process The lock needs to learn if your door is a right- or left-handed . ! 0 Enter PC DO THIS FIRST 2.
PAGE 15
OPERATING INSTRUCTIONS 6. Toggle Auto-Lock On/Off Enter PC 5 Note: The preset delay-time is 30 seconds, you can change the time by following instructions #7. Repeat the steps in #6 to cancel the auto-locking function. 7. Set Auto-Lock Time Delay Enter PC Enter Seconds (10~99) 6 Note: 10–99 seconds delay-time available. 8. Enable/Disable All User Codes Enter PC 7 Note: Auto-locking and keypad locking functions will be invalid when user codes are disabled.
PAGE 16
OPERATING INSTRUCTIONS 10. Restore Default Settings Press R R Note: Press the button for more than 5 seconds; the programming is reset back to the original factory codes once you hear 3 long beeps. After restoring default settings, you must run the door handing identifying process (#1) again before programming any other functions. R Reset button CARE AND MAINTENANCE Do not use any chemical liquid or lubricating oil with additives to clean the lock body. It will damage the surface or even mainboard.
PAGE 17
TROUBLESHOOTING PROBLEM POSSIBLE CAUSE CORRECTIVE ACTION After installing the lockset and batteries, the door can’t be locked and three short beeps are emitted when you press the lock button. The door-handing identification process isn’t yet complete. Refer to step1, page13. You’ve installed the lockset and batteries, but you still get no response when you press any button. Batteries were installed incorrectly and cable connect incorrectly.
PAGE 18
TROUBLESHOOTING PROBLEM POSSIBLE CAUSE CORRECTIVE ACTION The door can be locked normally, but when you try to unlock it, you hear three short beeps and the lock won't unlock when you enter the user code and press the lock button. The functioning of the Call our customer micro-switch is abnormal. service department. While the door is locked, you hear the latch bolt coming out when you press the lock button to lock the door; however, three short beeps are emitted.