Installation Guide

A. Close door until latch bolt touches door jamb to locate
strike placement.
Mark horizontal centerline of strike parallel with the
center of the latch bolt.
B. Measure one half of door thickness from door stop and
mark for the vertical centerline of strike.
C. Match screw holes on strike with centerlines on jamb.
Mark outline of strike plate and chisel out until strike is
flush with jamb.
D. Install both of deadlock reinforcement plate and strike
plates, tighten screws.
Adjustable tang on strike can be bent in or out to
eliminate loose fit between door and door stop.
Drill aperture
which is same as strike box 1-9/64" (29mm) deep at
intersection of horizontal and vertical center line of strike.
Put the cylinder tailpiece horizontally and get through the latch hole as illustration, then
tighten the machine screws to fix.
Secure and fasten the install interior mechanism firmly through the screws respectively as
shown in figure.
7. INSTALL INTERIOR MECHANISM 8. INSTALL STRIKEPLATES
H13 H13
H13 H13
ENTRANCE HANDLESET INSTALLATION INSTRUCTIONS
THIS INSTRUCTIONS IS PREPARED
TO PROVIDE YOU INFORMATION ON
HOW TO INSTALL YOUR LOCK
PROPERLY. READ THIS INSTRUCTION
CAREFULLY BEFORE ATTEMPTING TO
INSTALL LOCK.
BEFORE PROCEEDING:
1. CHECK BACKSET OF YOUR LOCK
BACKSET OF YOUR LOCK IS INDICATED ON
PACKAGING BOX, 2-3/8" OR 2-3/4" SOME
MODELS ARE SUPPLIED WITH ADJUSTABLE LATCH.
2. CHECK BACKSET OF YOUR DOOR
BACKSET IS A DISTANCE MEASURED FROM DOOR
EDGE TO CENTER OF LOCK, EITHER 2-3/8" OR 2-3/4".
3. MATCH BACKSET OF YOUR LOCK WITH BACKSET
OF YOUR DOOR
MAKE SURE YOUR LOCK HAS SAME BACKSET SIZE AS
YOUR DOOR. FOR LOCK SUPPLIED WITH ADJUSTABLE
LATCH, YOU MAY ADJUST THE BACKSET IF NECESSARY
ACCORDING TO STEP 1 IN THIS
INSTRUCTIONS.
TOOL REQUIRED FOR NEW INSTALLATION:
PHILLIPS HEAD SCREWDRIVER
˙ 3/8" ELECTRIC POWER DRILL
˙ 2" , 1", 1-5/8" AND 3/8" DRILL BITS
˙ 1" CHISEL
˙ HAMMER
TOOL REQUIRED FOR REPLACEMENT INSTALLATION:
˙ PHILLIPS HEAD SCREWDRIVER
˙
FOR USE ON DOORS 1-3/8" TO 2" (35mm~51mm)THICKNESS
A. Drill 2-1/8" (54mm) holes from both sides
of door to avoid splintering.
B. Drill 1" (25.4mm) latch holein door edge.
C. Drill 1" (25.4mm ) deadbolt hole
3-3/4" (95.26mm) deep.
D. Drill 3/8" (10mm) hole for
exterior handle mounting screw.
2-1/8"
(54mm)
Hole
1" (25.4mm)
Holes
3/8" (10mm)
Hole
2-1/8"
(54mm)
Hole
Make mark for 3/8" (10mm) hole
on door face.
Height 36" to 38" (914mm
~965mm) from floor
Use template enclosed to mark holes on door face.
Before proceeding:
Backset is the distance from the door edge to the center of lock, either 2-3/8" or 2-3/4" (60mm or 70mm).
Your latch backset was preset at the factory for 2-3/8" (60mm) backset.
If 2-3/4" (70mm) backset is required follow the adjustment instructions in Step 1A for latch and in 1D for deadbolt.
If 2-3/8" (60mm) backset is required.
1A. If 2-3/4" (70mm) backset is required, pull spindle
cam all the way to the right edge of adjusting hole.
1B. Be sure the 2-3/4" (70mm) cam
hole is properly aligned.
1C. Your latch is now set
for 2-3/4" (70mm) backset.
Deadlock Backset Adjustment :
Latch Backset Adjustment :
1D. If 2-3/4" (70mm) backset is required, rotate
latch cam to retract the latchbolt to the
unlock position.
1E. Push the change button up. Hold
torque plate and torque spring, pull
extension plate all the way out.
1. LATCH BACKSET ADJUSTMENT
1A 1B
1C
1F1D
1E
Right Wrong
1F. Your latch is now set for
2-3/4" (70mm) backset.
2. MARK DOOR
3. DRILL HOLES
Make mark for 1"
(25.4mm) hole on
center of door edge.
8-7/16"
(214mm)
5-1/2"
(139.7mm)
60
70
Chisel 5/32" (4mm)
Deep
Bottom
Handle
Latch
Top
Deadbolt
Latch
A. Insert latches in holes, keeping parallel to edge of door.
Mark outline and remove latch.
Note: cut out must be parallel to edges of door.
C. Insert bottom latch and secure with wood screws.
D. Repeat procedure for top deadbolt latch.
Note : watch the up mark stamped on deadbolt latch.
B. Chisel 5/32" (4mm) deep or until latch face is flush with door edge.
4. INSTALL LATCHES
Face plate will be flush with door
edge after tighten the screws.
A. B. C. D.
5. INSTALL EXTERIOR HANDLE
Place exterior handle with stems and torque spindle into
latch as shown. Press tightly against door face and fix with
inside mounting plate by screws as below.
Stems
Mounting plate
Bottom Screw
and Washer
6. CAM DIRECTION SETTING PROCEDURE
Install the mounting plate on the door
with screws.
Turn the turn-piece to a vertical
position.
Switch the Cam position to R if the door is right-sided
and vice versa.
Caution: Be sure the cam is turned to the correct
position.
If the cam is set to the wrong position, the latch
could not be retracted completely.
R L
Drill and
Point Center
For Strike
Vertical
Center line
of jamb
Door Stop
Mark Outline
of strike
Plates
A. B.
C.
D.
Center
Of Strike
Jamb
Exterior
Handle
Interior Lever
Machine
Screws
Cylinder
Interior Knob