Installation Guide

11. ADJUSTABLE LATCH FOR BOTTOM HANDLE LATCH
˙PULL SPINDLE CAM ALL THE WAY TO
RIGHT EDGE OF ADJUSTING HOLE.
˙THIS LATCH IS FOR 2-3/8" (60mm) BACKSET.
˙TO RE- SET 2-3/8" (60mm)
BACKSET JUST PUSH
SPINDLE CAM TO LEFT
EDGE OF ADJUSTING HOLE .
˙BE SURE THE 2-3/4" (70mm) STEM HOLE IS PROPERLY
ALIGNED.
˙YOUR LATCH IS NOW SET FOR A 2-3/4" (70mm) BACKSET.
SCREW HOLE
FOR 23/8" BACKSET
CHANGE LEVER
10. ADJUSTABLE LATCH FOR TOP DEADBOLT
LATCHBOLT
RETRACT
˙YOUR LATCH IS NOW SET FOR 2-3/4" (70mm) BACKSET.
LATCH CRANK
TORQUE PLATE
TORQUE SPRING
NOTE: BE SURE TO KEEP SPINDLE CAM SQUARE IN CORRECT
POSITION AS ILLUSTRATED BEFORE PUSHING SPINDLE
CAM TO LEFT. OTHERWISE YOU WILL HAVE DIFFICULTY
IN PUSHING SPINDLE CAM TO LEFT.
˙PUSH THE CHANGE LEVER AGAINST THE TOP.
˙HOLD TORQUE PLATE AND TORQUE SPRING,
THEN PULL EXTENSION PLATE ALL THE WAY OUT.
˙BE SURE THE 2-3/4"(70mm) SCREW HOLE IS
PROPERLY ALIGNED AND CHANGE LEVER JUMPS
DOWN TO ORIGINAL POSITION.
˙ROTATE LATCH CRANK TO RETRACT THE
LATCHBOLT TO THE UNLOCK POSITION.
˙LATCH MAY BE ADJUSTED BACK TO 2-3/8"(60mm)
BACKSET BY RETRACTING THE LATCHBOLT, PUSHING
UP THE CHANGE LEVER AND MOVING THE EXTENSION
PLATE BACK TO IT'S ORIGINAL POSITION.
NOTE: BE SURE THE 2-3/8"(60mm) SCREW HOLE IS
PROPERLY ALIGNED AND CHANGE LEVER
JUMPS DOWN TO ORIGINAL POSITION
AFTER ADJUSTMENT.
10B 11B
10A 11A
10D 11D
10C 11C
1
2
PULL
OUT
PUSH UP
1
2
PUSH
EXTENSION PLATE
PUSH UP
SCREW HOLE
FOR 2-3/4" BACKSET
CHANGE LEVER
EXTENSION PLATE
TORQUE SPRING
TORQUE PLATE
LATCH CRANK
PULL
SLIDING PLATE
SPINDLE CAM
SPINDLE CAM
SLIDING PLATE
SLIDING PLATE
ADJUSTING HOLE
RIGHT EDGE OF ADJUSTING HOLE
2-3/8" (60mm) STEM HOLE
2-3/4" (70mm) STEM HOLE
PUSH
SPINDLE CAM
LEFT EDGE OF ADJUSTING HOLE
"
"
4
8
2
3
/
/
3
2
"
"
4
8
2
3
/
/
3
2
"
"
4
8
2
3
/
/
3
2
1. SOME MODELS ARE SUPPLIED WITH ADJUSTABLE LATCH TO FITS 2-3/8" OR 2-3/4" (60mm OR 70mm) BACKSET.
ADJUSTABLE LATCH WAS PRESET AT FACTORY FOR 2-3/8" (60mm) BACKSET. IF A 2-3/4" (70mm) IS REQUIRED,
PLEASE FOLLOW STEP 10A THRU 10D FOR ADJUSTMENT.
2. SOME MODELS ARE SUPPLIED WITH 4-WAY LATCH FITS 2-3/8" OR 2-3/4" (60mm OR 70mm) BACKSET AND
ALSO FITS MORTISE IN OR DRIVE IN. TO CONVERT.
MORTISE IN TO DRIVE IN, JUST ROTATE LATCH FACE
CLOCKWISE 20 ° THEN PULL OUT LATCH FACE.
IF 2-3/4" (70mm) IS REQUIRED, PLEASE FOLLOW STEP.
10A THRU 10D FOR ADJUSTMENT.
1. SOME MODELS ARE SUPPLIED WITH ADJUSTABLE LATCH TO FITS 2-3/8" OR 2-3/4" (60mm OR 70mm) BACKSET.
ADJUSTABLE LATCH WAS PRESET 2-3/8" (60mm) AT FACTORY. IF A 2-3/4" (70mm) IS REQUIRED, PLEASE
FOLLOW STEP 11A THRU 11D FOR ADJUSTMENT.
2. SOME MODELS ARE SUPPLIED WITH 4-WAY LATCH WHICH CAN FIT 2-3/8" OR 2-3/4" (60mm OR 70mm) AND
ALSO CAN FIT MORTISE IN OR DRIVE IN. TO CONVERT
MORTISE IN TO DRIVE IN, JUST ROTATE LATCH FACE
CLOCKWISE 20 ° THEN PULL OUT LATCH FACE.
IF A 2-3/4" (70mm) IS REQUIRED, PLEASE FOLLOW
STEP 11A THRU 11D FOR THE ADJUSTMENT.
7. MARK JAMB 8. MARK OUTLINE OF STRIKES 9. DRILL HOLES AND INSTALL STRIKES
4. INSTALL EXTERIOR HANDLE 5. INSTALL INTERIOR MECHANISM 6. INSTALL CYLINDER DEADLOCK AND TRIM
3. INSTALL LATCHES
1. MARK DOOR
2. DRILL HOLES
VERTICAL
CENTRELINE
OF JAMB
DOOR
STOP
DRILL
POINT
CENTER
FOR
STRIKE
MARK
OUTLINE
OF STRIKE
PLATES
LATCH FACE
MORTISE IN
LATCH
2
3
8
/
/
4
3
2
"
"
LATCH FACE
MORTISE IN LATCH
PULL
OUT
DRIVE IN LATCH
ROTATE 20 °
ROTATE 20 °
CENTER
OF
STRIKE
JAMB
A. INSERT LATCHES IN HOLES,
KEEPING PARALLEL TO EDGE OF DOOR.
MARK OUTLINE AND REMOVE LATCH.
C. INSERT BOTTOM LATCH AND SECURE WITH
WOOD SCREWS.
D. REPEAT PROCEDURE FOR
TOP DEADBOLT LATCH.
NOTE: WATCH THE UP
MARK STAMPED
ON DEADBOLT
LATCH.
A. DRILL ( ) HOLE IN DOOR JAMB.
CAUTION: TO ASSURE PROPER LOCKSET FUNCTION.
HOLES IN DOOR JAMB MUST BE DRILLED
1" (25.4mm) DEEP.
B. CHISEL OUTLINE FOR STRIKE PLATES 1/16" (1.5mm) DEEP
OR UNTIL PLATES ARE FLUSH WITH DOOR JAMB.
C. INSTALL STRIKES PLATES AND SECURE WITH WOOD
SCREWS.
1" 25.4mm
A. CLOSE DOOR UNTIL LATCHBOLT
TOUCHES DOOR JAMB. MARK
DOOR JAMB AS SHOWN WITH
A PENCIL.
B. CENTER THE STRIKE PLATES ON
THE DOOR JAMB.
MEASURE ONE HALF OF DOOR
THICKNESS FROM DOOR STOP
AND VERTICALLY MARK DRILL
POINT CENTER FOR STRIKE.
PLACE STRIKES IN POSITION
AND MARK OUTLINE OF
STRIKE PLATES.
TAILPIECE
TAILPIECE
CYLINDER TRIM
INSIDE MATING TRIM
SCREW HOLES
MACHINE
SCREWS
MACHINE
SCREWS
BOTTOM SCREW
AND WASHER
SECURE AND FASTEN THE INSTALL INTERIOR MECHANISM FIRMLY
THROUGH THE SCREWS RESPECTIVELY AS SHOWN IN FIGURE.
FOR SINGLE CYLINDER
A. INSERT CYLINDER IN DECORATIVE TRIM AND
PRESS AGAINST DOOR. INSERT TAILPIECE
HORIZONTALLY THROUGH LATCH HOLE.
B. SLIDE INSIDE MATING TRIM ONTO
TAILPIECE AND SECURE WITH
MACHINE SCREWS.
PLACE EXTERIOR HANDLE WITH STEMS AND SQUARE SPINDLE INTO
LATCH AS SHOWN. PRESS TIGHTLY AGAINST DOOR FACE.
A. DRILL 2-1/8" (54mm)
HOLES FROM BOTH
SIDES OF DOOR.
B. DRILL 1" (25.4mm)
HOLES IN DOOR EDGE
FOR LATCH.
C. DRILL 3/8" (10mm)
HOLE FOR EXTERIOR
HANDLE MOUNTING
SCREW.
D. TO AVOID SPLINTERING
DRILL HOLES FROM
BOTH SIDES.
BOTTOM
HANDLE
LATCH
EXTERIOR
HANDLE
INTERIOR
KNOB
TOP
DEADBOLT
LATCH
CHISEL
1/8" (3mm)
DEEP
2-1/8"
(54mm)
HOLE
2-1/8" (54mm)
HOLE
MAKE MARK
FOR 1" (25.4
mm ) HOLE
ON CENTER
OF DOOR
EDGE.
1" (25.4mm)
HOLES
MAKE MARK FOR 3/8"
(10mm) HOLE ON
DOOR FACE.
3/8" (10mm)
HOLE
HEIGHT 36" TO 38"
(914mm~965mm)
FROM FLOOR
USE TEMPLATE ENCLOSED TO MARK HOLES ON DOOR FACE.
THIS INSTRUCTIONS IS PREPARED
TO PROVIDE YOU INFORMATION ON
HOW TO INSTALL YOUR LOCK
PROPERLY. READ THIS INSTRUCTION
CAREFULLY BEFORE ATTEMPTING TO
INSTALL LOCK.
BEFORE PROCEEDING:
1. CHECK BACKSET OF YOUR LOCK
BACKSET OF YOUR LOCK IS INDICATED ON
PACKAGING BOX, 2-3/8" OR 2-3/4" SOME
MODELS ARE SUPPLIED WITH ADJUSTABLE LATCH.
2. CHECK BACKSET OF YOUR DOOR
BACKSET IS A DISTANCE MEASURED FROM DOOR
EDGE TO CENTER OF LOCK, EITHER 2-3/8" OR 2-3/4".
3. MATCH BACKSET OF YOUR LOCK WITH BACKSET
OF YOUR DOOR
MAKE SURE YOUR LOCK HAS SAME BACKSET SIZE AS
YOUR DOOR. FOR LOCK SUPPLIED WITH ADJUSTABLE
LATCH, YOU MAY ADJUST THE BACKSET IF NECESSARY
ACCORDING TO STEP 10 AND STEP 11 IN THIS
INSTRUCTIONS.
TOOL REQUIRED FOR NEW INSTALLATION:
PHILLIPS HEAD SCREWDRIVER
˙ 3/8" ELECTRIC POWER DRILL
˙ 2-1/8" , 1" AND 3/8" DRILL BITS
˙ 1" CHISEL
˙ HAMMER
TOOL REQUIRED FOR REPLACEMENT INSTALLATION:
˙ PHILLIPS HEAD SCREWDRIVER
˙
B. CHISEL 1/8" (3mm) DEEP OR UNTIL LATCH
FACE IS FLUSH WITH DOOR EDGE.
NOTE: CUT OUT MUST BE PARALLEL TO
EDGES OF DOOR
"
"
2
3
4
/
/
8
3
2
PULL
OUT
DRIVE IN LATCH
FOR DOUBLE CYLINDER
A. INSERT EXTERIOR CYLINDER IN DECORATIVE
TRIM AND PRESS AGAINST DOOR FACE.
INSERT TAILPIECE HORIZONTALLY INTO
LATCH HOLE.
NOTE: TAILPIECE OF EXTERIOR CYLINDER
SHOULD BE INSERTED HORIZONTALLY
THROUGH LATCH HOLE FIRST.
B. INSERT INTERIOR CYLINDER TAILPIECE
VERTICALLY THROUGH LATCH HOLE AND
SECURE WITH MACHINE SCREWS.
NOTE: THE INTERIOR TAILPIECE SHOULD
BE INSERTED VERTICALLY THROUGH
LATCH HOLE.
ENTRANCE HANDLESET INSTALLATION INSTRUCTIONS
H1 H1
H1 H1
8-7/16" (214mm)
5" (127mm)
SQUARE
SPINDLE
STEMS
MACHINE
SCREWS
CYLINDER TRIM
TAILPIECE
TAILPIECE
FOR SINGLE HANDLE
FOR DOUBLE HANDLE
"
/
8
3
2
"
/
4
3
2
"
/
8
3
2
"
/
4
3
2
"
/
8
3
2
"
/
4
3
2
"
/
8
3
2
"
/
4
3
2
"
/
8
3
2
"
/
4
3
2
"
/
8
3
2
"
/
4
3
2