Installation Guide

ManualsBrandsDelaney ManualsDoor HardwareDelaney LP250 Black Digital Keypad Entry Door Lever

TEMPLATE

45 40 35

1-3/4" 1-9/16" 2" 1-3/8"

Fit here on door edge

FOR BACKSET 70mm (2-3/4”)

FOR BACKSET 60mm (2-3/8”)

Mark Ø1" (25.4mm) hole at

center of door edge.

Ø54mm (2-1/8")

K P

ELECTRONIC KNOB & LEVER LOCK

USER MANUAL

Product : KEYPAD ELECTRONIC KNOB & LEVER LOCK

Purchase Date :

Name & Address of Distributor :

Limited Warranty Statements

1. Warranty

Tong Lung Metal Industry Co., Ltd. (hereafter “TL”) warrants the Product to be free

from defects in material and workmanship for a period of 12 months

from the original date of purchase.

If you discover a defect in the Product covered by this warranty, we will repair or

replace the item at our option using new or refurbished components.

2. Exclusions

This warranty covers defects in manufacturing discovered while using the

Products as recommended by TL rather than occurred by the act of God,

and damages caused by misuse, abuse, and unauthorized modification.

3. Limited of Liability

TL will not be held liable for incidental or consequential losses or damages

to any act of God.

4. Reminder

Service requirement shall subject to the presentation of this warrant card

and defective parts to the manufacture TL.

The warranty card will not be reissued if lost.

TONG LUNG METAL INDUSTRY CO., LTD.

Attention : Please do not use the "electronic" screwdriver for installation.

Summary of content (7 pages)

PAGE 1
TEMPLATE Fit here on door edge 40 35 2" 1-3/4" 1-9/16" 1-3/8" 51 45 Mark Ø1" (25.4mm) hole at center of door edge. Limited Warranty Statements 1. Warranty Tong Lung Metal Industry Co., Ltd. (hereafter “TL”) warrants the Product to be free from defects in material and workmanship for a period of 12 months from the original date of purchase. If you discover a defect in the Product covered by this warranty, we will repair or replace the item at our option using new or refurbished components. 2.
PAGE 2
KEYPAD ELECTRONIC LEVER & KNOB INSTALLATION INSTRUCTION The BACKSET is the distance between the center of cross bore and edge bore of the door. Adjustable latch fits both BACKSET of 2-3/8” (60mm) and 2-3/4” (70mm). Please follow the steps shown below for BACKSET adjustment. b Face the door from outside, the door is left handed if the hinge is on the left-hand side of the door, whereas the door is right handed if the hinge is on the right-hand side of the door. Door (Left Handed) a.
PAGE 3
7. Install Inside Mounting Plate 5. Install Strike a b Mounting Pass the IC wire through the wire hole on the Plate mounting plate and fix the mounting plate with screws. If outside lock assembly is lopsided, IC wire please loosen the screws to adjust it's position Screws and tighten the screws again. c a. Half-close the door to lay the latchbolt against the door frame. Mark the position of faceplate as an indication. Place the strike against the door frame and mark it's erimeter.
PAGE 4
9. Change Lever Handing a. Be sure the levers are unlocked. Insert the provided pin wrench into the small hole on the neck of lever and apply pressure to depress the catch and pull out the lever from the stem. Follow the same steps to remove interior lever and exchange the position of inside and outside levers.      1 2 3 4 5 6 7 8 9 0    b. Remove the cylinder from lever and insert it into opposite lever.
PAGE 5
■ Specification/Function 6.User Code 1.Power 6V, four AA（1.5V）Alkaline batteries. 2.Low Battery 2-1 The batteries should be changed immediately once you see button1 flashes in red and hear 10 rapid beep sounds when press programming button. 2-2 All settings are retained in the memory and will not be affected even if the battery is completely dead. 2-3 The lock still can be operated by key even there is a power outage. 3.
PAGE 6
■ Pass Code & Function Set up 12.Unlock the door 12-1 The lockset will be unlocked by key or pressing User Code on keypad from outside or by interior turn-button. 12-2 To unlock the door on the keypad, enter the User Code and then press the Programming/Enter button. 13.Lock the door The lockset will be locked by key or pressing Programming Button on keypad from outside or by interior turn-button. 14.
PAGE 7
■ Function Programming Programming Code (PC) Programming Code (PC) USER Code (UC) USER Code (UC) Add New User Code Enter PC Toggle Mute On/Off 1 Enter New UC Enter PC Remark : Up to 6 sets of User Code can be saved. User Code should be 4-10 digits in length. Delete An Existing User Code Enter PC 2 Enter PC 3 Enter New PC 9 Enter new disposable UC Remark : Disposable code will be no longer valid once being used.